仿壁虎刚毛阵列对卫星表面吸附能力模型与计算

壁虎脚的粘着机理对航天机器人脚掌的研制和开发具有重要启发意义.通过单根刚毛与光滑表面黏着力模型与计算、卫星粗糙表面分布模型与接触概率与计算、刚毛阵列与卫星粗糙表面黏着力模型与计算等，分析仿壁虎刚毛阵列对卫星表面的吸附能力，发现在一定条件下仿壁虎刚毛阵能够在太空失重环境中黏着在卫星表面，对航天舱内爬行机器人、管道机器人的研制和开发具有重要的启示意义.     

Evaluation of SARAL/AltiKa performance using GNSS/IMU equipped buoy in Sajafi,Imam Hassan and Kangan Ports

Performance of SARAL/AltiKa mission has been evaluated within 2016 altimeter calibration/validation framework in Persian Gulf through three campaigns conducted in the offshore waters of Sajafi, Imam Hassan and Kangan Ports, while the altimeter overflew the passes 470, 111 and 25 on 13 Feb, 7 March and 17 June 2016, respectively. As the preparation, a lightweight buoy was equipped with a GNSS receiver/choke-ring antenna and a MEMS-based IMU to measure independent datasets in the field operations. To obtain accurate sea surface height (SSH) time series, the offset of the onboard antenna from the equilibrium sea level was predetermined through surveying operations as the buoy was deploying in the onshore waters of Kangan Port. Accordingly, the double-difference carrier phase observations have been processed via the Bernese GPS Software v. 5.0 so as to provide the GNSS-derived time series at the comparison points of the calibration campaigns, once the disturbing effects due to the platform tilt and heave have been eliminated. Owing to comparing of the SSH time series and the associating altimetry 1?Hz GDR-T datasets, the calibration/validation of the SARAL/AltiKa has been performed in the both cases of radiometer and ECMWF wet troposphere corrections so as to identify potential land contamination. An agreement of the present findings in comparison with those attained in other international calibrations sites confirms the promising feasibility of Persian Gulf as a new dedicated site for calibration/validation of ongoing and future altimetry missions.     

Six sigma robust design optimization for thermal protection system of hypersonic vehicles based on successive response surface method

Lightweight design is important for the Thermal Protection System(TPS) of hypersonic vehicles in that it protects the inner structure from severe heating environment. However, due to the existence of uncertainties in material properties and geometry, it is imperative to incorporate uncertainty analysis into the design optimization to obtain reliable results. In this paper, a six sigma robust design optimization based on Successive Response Surface Method(SRSM) is established for the TPS to improve the reliability and robustness with considering the uncertainties. The uncertain parameters related to material properties and thicknesses of insulation layers are considered and characterized by random variables following normal distributions. By employing SRSM, the values of objective function and constraints are approximated by the response surfaces to reduce computational cost. The optimization is an iterative process with response surfaces updating to find the true optimal solution. The optimization of the nose cone of hypersonic vehicle cabin is provided as an example to illustrate the feasibility and effectiveness of the proposed method.     

Validation of non-linear split window algorithm for land surface temperature estimation using Sentinel-3 satellite imagery: Case study; Tehran Province,Iran

In recent years, land surface temperature (LST) has become critical in environmental studies and earth science. Remote sensing technology enables spatiotemporal monitoring of this parameter on large scales. This parameter can be estimated by satellite images with at least one thermal band. Sentinel-3 SLSTR data provide LST products with a spatial resolution of 1 km. In this research, direct and indirect validation procedures were employed to evaluate the Sentinel-3 SLSTR LST products over the study area in different seasons from 2018 to 2019. The validation method was based on the absolute (direct) evaluation of this product with field data and comparison (indirect) evaluation with the MODIS LST product and the estimated LST using the non-linear split-window (NSW) algorithm. Also, two emissivity estimation methods, (1) NDVI thresholding method (NDVI-THM) and (2) classification-based emissivity method (CBEM), were used to estimate the LST using the NSW method according to the two thermal bands of Sentinel-3 images. Then, the accuracy of these methods in estimating LST was evaluated using field data and temporal changes of vegetation, which the NDVI-THM method generated better results. For indirect evaluation between the Sentinel-3 LST product, MODIS LST product, and LST estimated using NSW, four filters based on spatial and temporal separates between pairs of pixels and pixel quality were used to ensure the accuracy and consistency of the compared pairs of a pixel. In general, the accuracy results of the LST products of MODIS and Sentinel-3, and LST estimated using NSW showed a similar trend for LST changes during the seasons. With respect to the two absolute and comparative validations for the Sentinel-3 LST products, summer with the highest values of bias (?1.24 K), standard deviation (StDv = 2.66 K), and RMSE (2.43 K), and winter with the lowest ones (bias of 0.14 K, StDv of 1.13 K, and RMSE of 1.12 K) provided the worst and best results for the seasons in the period of 2018–2019, respectively. According to both absolute and comparative evaluation results, the Sentinel-3 SLSTR LST products provided reliable results for all seasons on a large temporal and spatial scale over our studied area.     

超临界CO2技术对空心/实心石英混编纤维表面改性

采用热处理+溶剂浸洗+超临界CO2技术对空心/实心石英混编纤维表面进行预处理,同时利用超临界流体的携带与渗透作用,将KH-560偶联剂引入纤维表面进行改性。采用接触角测试、表/界面张力测试、树脂吸附量测试、力学性能测试、扫描电镜等分别测试纤维表面能、胶液表面张力与接触角、胶液与纤维浸润性,观察纤维表面形貌结构,分析复合材料的力学与介电性能。结果表明:采用热处理+溶剂浸洗+超临界CO2技术可有效去除空心/实心石英混编纤维表面浸润剂,提高纤维表面能,促进胶液与纤维的完全浸润,最终改善复合材料力学与介电性能。     

永磁同步电机最优滑模控制

为了减少永磁同步电机调速中的动态误差,提出了一种积分性能最优的滑模控制方法。该方法以滑模控制中的动态误差为性能指标,在此基础上建立最优切换函数,并采用最优控制理论对滑模控制器进行设计。用该方法设计的滑模控制系统,通过滑模面斜率的连续变化,能够加速系统状态变量到达滑模面的过程,极大地提高对参数摄动和外部干扰的鲁棒性。仿真结果表明,该时变滑模面控制方法使系统具有无超调、快速、稳定等优点,提高了系统的鲁棒性。     

基于双变量预测控制的表贴式永磁同步电机直接转矩控制系统

基于电压矢量幅值和相角为变量的表贴式永磁同步电机(SPMSM)定子磁链幅值和转矩表达式,给出了9个不同幅值和相角的备选电压矢量,采用预测控制计算得出施加不同电压矢量下一时刻的定子磁链幅值和转矩值,建立了基于磁链和转矩误差的目标函数,并选择使目标函数最小的电压矢量为作为下一时刻施加的最优电压矢量。仿真结果表明:在双变量预测控制下,SPMSM直接转矩控制系统运行良好,定子磁链轨迹为理想圆,磁链和转矩均符合控制要求,转速跟踪良好,定子电流波形正弦。进一步对比分析表明:与开关表和固定电压矢量选择策略相比,双变量预测控制能显著减小转矩和磁链脉动。与开关表相比,转矩脉动均方根误差降低了62.92%,磁链脉动均方根误差降低了45.05%,评价函数均值降低了60.30%；与固定电压矢量选择策略相比,转矩脉动均方根误差降低了22.40%,磁链脉动均方根误差降低了3.85%,评价函数均值降低了15.93%。     

表贴式永磁同步电机直接转矩控制变幅值预测控制研究

基于以电压矢量幅值为变量的表贴式永磁同步电机(SPMSM)磁链和转矩方程,采用预测控制计算得出施加不同电压矢量幅值的下一时刻磁链和转矩值,选择使磁链和转矩误差目标函数最小的电压矢量幅值作为最优值,从而确定下一时刻施加的电压矢量。仿真结果表明:在电压矢量变幅值预测下,SPMSM直接转矩控制(DTC)系统运行良好,定子磁链轨迹为理想圆,磁链和转矩均符合控制要求,转速跟踪良好,定子电流波形正弦。预测控制需要从备选电压矢量幅值集合中选择最优幅值。理论上,备选电压矢量幅值个数越多,系统优化效果越好,但也带来更大的计算负担。研究了9种等分电压矢量情况下变幅值预测控制系统的控制效果。根据控制效果和计算负担,提出变幅值预测控制将电压矢量幅值三等分较为理想。     

Electrochemical micromachining of micro-dimple arrays on cylindrical inner surfaces using a dry-film photoresist

The application of surface textures has been employed to improve the tribological performance of various mechanical components. Various techniques have been used for the application of surface textures such as micro-dimple arrays, but the fabrication of such arrays on cylindrical inner surfaces remains a challenge. In this study, a dry-film photoresist is used as a mask during through-mask electrochemical micromachining to successfully prepare micro-dimple arrays with dimples 94 lm in diameter and 22.7 lm deep on cylindrical inner surfaces, with a machining time of 9 s and an applied voltage of 8 V. The versatility of this method is demonstrated, as are its potential low cost and high efficiency. It is also shown that for a fixed dimple depth, a smaller dimple diameter can be obtained using a combination of lower current density and longer machining time in a passivating sodium nitrate electrolyte.     

三维攻击角度约束部分制导控制一体化设计

针对侧滑转弯(STT)导弹带有攻击角度约束的机动目标拦截问题，提出一种基于自适应终端滑模动态面控制的三维部分制导控制一体化(PIGC)设计方法。首先，建立了针对机动目标拦截的侧滑转弯导弹三维部分制导控制一体化设计模型，且不需要导弹速度微分体轴系分量信息。然后，使用终端滑模控制理论构建误差向量与虚拟控制量，达成精确拦截与攻击角度约束的控制目的；引入有限时间非线性收敛扩张状态观测器(ESO)来在线估计系统不确定性；设计自适应算子与自适应更新律对观测器的估计误差进行补偿，以提高方法的鲁棒性。最后，三维空间拦截仿真校验了方法在提高拦截精度与增强角度约束收敛性能的有效性。