半球谐振子疲劳寿命分析与仿真

半球谐振子的寿命和损伤是直接影响高精度半球谐振陀螺使用时长和安全性的重要因素。目前国内加工的半球谐振子所用的熔融石英玻璃材料主要依靠进口，采用传统的疲劳寿命实验确定方法成本过于昂贵，因此需要利用疲劳分析软件对半球谐振子的疲劳寿命进行分析。文章通过半球谐振陀螺应力分析，采用ANSYS软件对熔融石英半球谐振子进行应力分析仿真，确定因残余应力所引起的疲劳危险部位，并在疲劳部位进行裂纹扩展分析，得到 、 和 型应力强度因子，以使在半球谐振子结构设计和使用过程中对易疲劳的部位进行有效监控和预防。     

石英玻璃的等离子体抛光技术研究现状

具有耐腐蚀、热膨胀系数低等诸多优良物理化学特性的石英玻璃在高性能光学系统中被广泛使用。要求元件达到纳米级别的表面粗糙度，而且没有损伤层和残余应力，因此精加工之后的超精密抛光工序尤为重要。本文介绍了气囊、磁流变、弹性发射、离子束等几种石英玻璃的精密抛光方法，侧重阐述了国内外等离子体的抛光技术，包括等离子体辅助化学刻蚀、等离子体喷射加工、等离子化学蒸发加工研究进展及取得的成果；且对等离子体的未来发展进行概述。     

不同流速比超声速混合层气动光学效应研究

针对不同流速比混合层流场气动光学效应问题，首先采用大涡模拟数值方法进行了数值仿真，其次用光线追迹方法进行了气动光学效应仿真，最后对混合层的气动光学效应进行了评价。结果表明，混合层流场涡结构与光程差极小值存在一一对应关系，并且其流速比低的混合层气动光学效应更加严重。同时，研究了不同光学参数对斯特列尔比的影响，得到了相应的规律。     

纵向波纹隔热屏气膜冷却特性实验

针对加力燃烧室纵向波纹隔热屏气膜冷却效果开展了细致的实验研究,利用红外热像仪测量了隔热屏壁面的温度分布,分析了隔热屏板型、吹风比、开孔率等参数对气膜冷却效率的影响。实验中板型选取了平板和纵向波纹隔热屏,吹风比变化范围是0.5~3.0,开孔率变化范围是1.4%~3.7%。结果表明:相比于平板隔热屏的气膜冷却效率沿程逐渐增加,纵向波纹隔热屏的气膜冷却效率随波纹板的起伏而起伏且大于平板隔热屏;随着吹风比的增加气膜冷却效率逐渐加大,在吹风比为3.0时达到最大值;气膜冷却效率在波峰处低,波谷处高,整体上随波纹板的起伏而波动,吹风比越小,气膜冷却效率随波纹板的起伏变化越明显;高吹风比(吹风比为2.0~3.0)下,气膜冷却效率沿程变化与增幅较为缓慢;整体上,随着开孔率的增加气膜冷却效率逐渐加大,小开孔率(开孔率为1.4%、2.7%)下的气膜冷却效率相差不大,但在次流背风侧,开孔率小的气膜冷却效率要小于开孔率大的气膜冷却效率。      

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

一种高动态低信噪比卫星导航信号捕获方法

为提升高动态低信噪比环境下卫星导航信号的捕获性能,提出了一种基于分数阶傅里叶变换(FrFT)及部分匹配滤波(PMF)的捕获方法。在该方法中,接收机首先利用PMF对接收信号做分段相干积分,随后借助快速傅里叶变换(FFT)对分段积分结果做离散快速FrFT,最后通过检测FrFT输出的峰值完成信号的捕获。由于具有多普勒频率变化率的卫星导航信号在FrFT后呈现能量聚焦特性,所提方法能够显著提高信号的长时间相干积分增益。同时对所提算法的捕获概率、平均捕获时间以及算法复杂度等性能指标进行了理论分析及计算机仿真验证。仿真表明,与传统的PMF-FFT方法相比,所提方法能够通过延长相干积分时间的方式有效提升高动态低信噪比卫星导航信号的捕获概率、降低捕获时间。     

比例与非比例加载下30CrMnSiA钢多轴高周疲劳失效分析

为了分析比例与非比例加载下,30CrMnSiA钢的多轴高周疲劳的失效规律。通过对30CrMnSiA钢材料开展比例与非比例(δ=90°)加载下的多轴高周疲劳试验,研究了应力幅比和相位差对疲劳寿命、断口特征及裂纹起裂角度的影响。试验结果表明,对于比例与非比例加载,随着应力幅比的增大,多轴疲劳寿命逐渐增加。对疲劳断口分析发现,裂纹萌生于试件表面,断口有明显的疲劳源区、扩展区和瞬断区,不同加载路径下的试件断口形式有明显差异。通过对起裂角度的分析发现,应力幅比大于0.25时表面裂纹有明显的第Ⅰ阶段向第Ⅱ阶段的转变,且第Ⅰ阶段沿着接近最大剪应力幅值平面方向扩展,第Ⅱ阶段沿着接近最大正应力平面方向扩展。此外,对典型试件的疲劳断口及表面扩展路径进行了分析,研究表明多轴疲劳试验试件裂纹的特征比值在0.3~0.5之间,且裂纹沿深度方向扩展至300 μm时占总寿命的85%以上。      

平板表面薄圆柱绕流摩擦力矢量场全局测量

针对壁面摩擦力矢量场测量问题,基于剪切敏感液晶(SSLC)涂层技术建立了一种测量平板表面摩擦力矢量场的方法。该方法基于多视角测量原理,采用六台同步相机从不同方向同时采集SSLC涂层在摩擦力作用下的颜色变化,与采用单台相机相比能够降低测量噪声,并且具有测量非定常流动的摩擦力场的潜力。应用该方法测量了平板表面薄圆柱绕流的摩擦力矢量场,结果表明:(1)SSLC涂层能够以彩色方式定性显示壁面摩擦力信息;(2)通过对不同方向观测的SSLC涂层颜色进行分析处理,该方法能够高分辨率测量薄圆柱绕流的摩擦力矢量场,详细地捕获了流动特征;(3)同一份SSLC涂层可以重复使用并且可用于测量不同的摩擦力矢量场。     

超高强高韧马氏体时效钢热变形及航天应用研究

对于航天用超高强高韧C300马氏体时效钢来说,热加工过程中获得等轴细小的再结晶晶粒是实现该钢强韧性最佳匹配的关键环节。采用Gleeble-3800热模拟试验机在温度为850～1 150℃、应变速率为0.01～10 s~(-1)的条件下,对超高强高韧C300马氏体时效钢进行高温轴向压缩变形试验,获得了高温流变曲线,并观察变形后的金相组织。结果表明:C300马氏体时效钢的流变应力和峰值应变随着变形温度的升高和应变速率的降低而减小;试验钢在真应变为0.92、应变速率为0.01～10 s~(-1)的条件下,随着变形速率的提高,其发生完全动态再结晶的温度也逐渐升高,最佳热变形温度区间为1 050～1 150℃;测得试验钢的热变形激活能Q值为391.2 kJ/mol,建立了其热变形本构方程。结果能为C300马氏体钢的数值模拟和热加工工艺的制定提供理论基础。     

A user-friendly yield criterion for metals exhibiting tension-compression asymmetry

The aim of this paper is to model the yielding asymmetry of pressure-insensitive metals, including but not limited to Ni₃Al alloys. The main focuses are put on the flexibility and manipulative convenience. The parameters of theory are kept to a minimum and can be determined by as few tests as possible. These requirements are fulfilled by constructing a yield function using the second and third-invariants of a linearly transformed stress tensor. The proposed yield criterion has a simple mathematical form and has only seven parameters when used in three-dimensional stresses. Compared with existing theories, the new yield criterion has much fewer parameters, which makes it very convenient for practical applications. The coefficients of the criterion are identified by an error minimization procedure. Applications to a Ni₃Al based intermetallic alloy as well as a Cu-Al-Be shape memory alloy and comparison to other criteria show that the proposed criterion has nearly the same predictive ability and flexibility with other criteria. The proposed yield criterion can estimate the coefficients by using less data, which is a big advantage compared with other similar theories, especially when there is a limited number of experimental data.