不同舵翼操纵面形式的水动力及艇后流场特性数值模拟研究

为研究共翼型舵和非共翼型舵两种操纵面形式的艇后流场特性及螺旋桨推进特性，基于SST(Menter)湍流模型建立了SUBOFF标准潜艇模型尾流场数值预报模型。经试验结果验证，所建立数值模型进行潜艇尾流场及螺旋桨推进性能预报具有较高精度。将SUBOFF潜艇模型的水平舵改进为共翼型舵及非共翼型舵，对艇后流场及水动力性能进行了预报。数值结果表明：在舵角小于10°时，共翼型舵使潜艇的俯仰力矩和垂向力相对非共翼型舵提升20%以上；在舵角超过10°时，共翼型舵的水动力优势随着舵角增大而减小。尾部流场预报显示：共翼型舵在小舵角时可以有效的消除舵翼结合处的涡流，同时共翼型舵可以有效的降低桨盘面伴流的不均匀性，对尾流品质的改善效果优于非共翼型舵。螺旋桨计算结果显示：共翼型舵螺旋桨推进系数在大部分舵角下都小于非共翼型舵，在舵角为20°时，共翼型舵相对非共翼型舵推力系数下降3.5%，扭矩系数下降2.4%；同时共翼型舵的桨盘面流场均匀度要优于非共翼型舵，舵角为5°时，共翼型舵桨盘面处流场不均匀度相对于非共翼型舵要降低7.1%，舵角为25°时则降低25.1%。     

基于有向图模型的民机航空电子系统故障诊断

结合民机航电系统外场可更换单元或模块（LRU/LRM）的故障模式及影响分析（FMEA）、故障树 分析和实时性要求，设计了基于时间故障传播图（TFPG）的系统故障诊断元模型和领域模型，研究了基于逻 辑和时间一致性检验的故障诊断算法，使用后向推理和可信度度量列出候选故障集。以飞行管理系统为例，构 造了其功能失效的TFPG 模型，并通过仿真验证了基于TFPG 的诊断在滤除级联效应和关联驾驶舱效应中的有 效性。     

Time delay compensation in lateral-directional flight control systems at high angles of attack

The previous studies of time delay compensation in flight control systems are all based on the conventional aerodynamic derivative model and conducted in longitudinal motions at low angles of attack. In this investigation, the effects of time delay on the lateral-directional stability augmentation system in high-α regime are discussed based on the $\dot{\beta }$ model, which is proposed in our previous work and proved as a more accurate aerodynamic model to reveal the lateral-directional unsteady aerodynamic characteristics at high angles of attack. Both the $\dot{\beta }$ model and the quasi-steady model are used for simulating the effects of time delay on the flying qualities in high-α maneuvers. The comparison between the simulation results shows that the flying qualities are much more sensitive to the mismatch of feedback gains than the state errors caused by time delay. Then a typical adaptive controller based on the conventional dynamic derivative model and a gain-prediction compensator based on $\dot{\beta }$ model are designed to address the time delay in different maneuvers. The simulation results show that the gain-prediction compensator is much simpler and more efficient at high angles of attack. Finally, the gain-prediction compensator is combined with a linearized $\dot{\beta }$ model reference adaptive controller to compensate the adverse effects of very large time delay, which exhibits excellent performance when addressing the extreme conditions at high angles of attack.     

垂直起降运载火箭返回轨迹不确定性优化

针对垂直起降运载火箭一子级在返回着陆的过程中存在的参数不确定性，提出了一种基于非侵入式多项式混沌展开的序列优化和可靠度评估的返回轨迹不确定性优化方法。首先，建立了返回多飞行段轨迹在确定性条件下的优化模型。然后，为同时兼顾轨迹的鲁棒性和可靠性，建立了由鲁棒最优目标函数、基于可靠度的路径约束和鲁棒等式约束组成的不确定性返回轨迹优化模型。最后，基于非侵入式多项式混沌展开方法对鲁棒目标函数和等式约束进行量化处理，将原随机鲁棒优化问题转化为高维状态空间中的等价确定性优化问题；为提高路径约束的可靠度评估效率，基于非侵入式多项式混沌展开方法对最可能点法进行改进，进一步发展了序列优化和可靠度评估策略。数值仿真结果表明，所提出的不确定性优化方法具有较好的鲁棒性，可以满足工程可靠性指标要求，同时还具有较高的精度和计算效率。     

几何尺寸约束的超燃冲压发动机推力喷管设计

针对机体/推进系统一体化要求，提出了一种几何尺寸约束的超燃冲压发动机推力喷管设计方法，以实现在满足几何约束条件下优化喷管的气动性能。采用数值模拟对提出的设计方法展开了研究，在此过程中，首先校核了数值方法有效性并确定了网格分辨率。进一步就喷管设计过程中2个关键设计因子——比例因子和非对称因子开展了影响研究。最后为验证本文提出的设计方法的有效性和优越性，将其与典型截短设计方法进行对比分析。结果表明，相比截短方法，本文提出的设计方法不仅能够获得满足几何约束的喷管，同时可使喷管推力系数、升力和俯仰力矩分别提升33.36%、265.75%和37.21%。此外，本文提出的设计方法还可以通过调整设计因子来获得不同气动性能的喷管，进而满足应用过程中的实际需求。     

航天器运输包装箱仿真验证平台技术研究

针对数量有限的物理跑车试验无法满足减振与保温性能测试需求的问题，提出一套航天器运输包装箱动力学与热学仿真验证方法，包括：建立适用于包装箱系统的刚柔耦合多体动力学系统，通过结合线路条件测试生成的动力学系统外部激励，实现减振性能虚拟跑车测试；建立基于计算流体力学的包装箱热学模型，通过模拟自然对流和空调控制，实现包装箱保温性能虚拟跑车测试；基于C/S架构和导航式流程设计思想，建立航天器运输包装箱仿真验证平台，通过实际案例证明该平台仿真结果与实际跑车测试数据具有较高的一致性。     

Evaluation of SARAL/AltiKa performance using GNSS/IMU equipped buoy in Sajafi,Imam Hassan and Kangan Ports

Performance of SARAL/AltiKa mission has been evaluated within 2016 altimeter calibration/validation framework in Persian Gulf through three campaigns conducted in the offshore waters of Sajafi, Imam Hassan and Kangan Ports, while the altimeter overflew the passes 470, 111 and 25 on 13 Feb, 7 March and 17 June 2016, respectively. As the preparation, a lightweight buoy was equipped with a GNSS receiver/choke-ring antenna and a MEMS-based IMU to measure independent datasets in the field operations. To obtain accurate sea surface height (SSH) time series, the offset of the onboard antenna from the equilibrium sea level was predetermined through surveying operations as the buoy was deploying in the onshore waters of Kangan Port. Accordingly, the double-difference carrier phase observations have been processed via the Bernese GPS Software v. 5.0 so as to provide the GNSS-derived time series at the comparison points of the calibration campaigns, once the disturbing effects due to the platform tilt and heave have been eliminated. Owing to comparing of the SSH time series and the associating altimetry 1?Hz GDR-T datasets, the calibration/validation of the SARAL/AltiKa has been performed in the both cases of radiometer and ECMWF wet troposphere corrections so as to identify potential land contamination. An agreement of the present findings in comparison with those attained in other international calibrations sites confirms the promising feasibility of Persian Gulf as a new dedicated site for calibration/validation of ongoing and future altimetry missions.     

Assessment of between-floor structural and topological properties on cognitive map development in multilevel built environments

The present study investigated cognitive map development in multilevel built environments. Three experiments were conducted in complex virtual buildings to examine the effects of five between-floor structural factors that may impede the accuracy of humans’ ability to build multilevel cognitive maps. Results from Experiments 1 and 2 (of three experiments) revealed that difficulties in developing multilevel cognitive maps are not solely caused by the z-axis offset, as is suggested in the literature, but are due to the factorial combination of a between-floor overlap and a z-axis offset. Results from Experiment 2 showed that this process becomes substantially more difficult when the reference directions between different floors have an angular offset from each other. Finally, results from Experiment 3 demonstrated that confusing between-floor heading shifts in aligned buildings did not make it reliably harder to build multilevel cognitive maps. The implications of these findings are discussed in terms of theories of mental representations in multilayered three-dimensional spaces, as well as for architectural design.     

Kalman弹道滤波器的快速收敛性研究

在弹道修正过程中，需根据一段实测弹道参数，准确地估算常规弹箭的飞行弹道。工程中，常应用Kalman滤波方法，结合质点弹道模型建立六状态滤波弹道模型。速度初值估计的准确性，是对滤波过程造成影响的主要因素。为改善这一状况，采用多项式拟合用以对速度状态进行估计并以此作为滤波初始值。在此种估计下滤波，速度滤波过程可快速收敛，位置滤波过程收敛速度大幅度提高，可使最优弹道诸元参数获取时间缩短30%。     

基于惯性定位定向的高铁轨检仪研究

根据高铁轨道静态检测的测量需求，设计了一种利用定位定向技术的0级轨检仪，详细阐述了其构成和工作原理，介绍了其特点。通过对比性分析论证，优选了一种测量精度高、操作方法简单且可大幅度提高测量效率的设计方案。理论仿真表明，本系统测量精度能够达到优于13mm/km水平。根据理论仿真结果搭建了原理简易验证设备，结合高铁测控网的测量基准，在一段高铁的弯道铁轨上进行了验证测试。从测试结果看，样机测量精度的重复性可以到达1mm/500m（1σ）的水平，10次测量效率优于500m/2h，表明采用定位定向技术的0级轨检仪具备实际工程化的潜力，以及提高测量效率和精度的能力。