PMSM电流预测控制参数误差量化分析方法

交流永磁同步电机（PMSM）电流环控制性能是制约交流伺服系统性能的关键。电流预测控制拥有更快的动态响应、更低的电流谐波和优良的转矩响应，但该算法依赖精确的电机模型，参数失配会引发稳态电流误差，无法输出额定转矩，进而导致电机转矩输出效率降低。根据永磁同步电机电流预测模型，详细分析了d、q轴电流静差产生的原因，以及电流预测控制对电机参数误差的敏感性，提出了一种参数误差量化分析方法。该方法引入了电机参数偏差因子，量化描述了电机电感、磁链参数误差与电流静差之间的制约关系。通过仿真分析，验证了所提方法的合理性，为高性能永磁伺服电流预测数字控制技术打下了良好基础。     

弹载变转速定量泵高动态压力控制特性分析

传统弹载电液伺服系统的液压能源采用有刷直流电机驱动恒压变量泵的方式，泵源压力在导弹飞行过程中设定值恒定，但在平飞段过程长、负载小，对能源压力需求低，造成弹上能源总利用率不高的问题，提出无刷直流电机驱动小排量液压泵的压力控制泵源的设计，在低气动负载阶段适当降低系统压力，进而降低节流损失与泄漏量，提高能量利用率。分析了变转速定量泵的流量压力特性曲线，通过建立基于变转速压力控制泵源的位置电液伺服系统数学模型与仿真模型，分析了变转速定量泵压力控制系统在典型工况下的位置跟踪、系统压力变化与能量利用效率，验证了压力控制系统能够在导弹平飞段保证位置伺服系统跟踪正常的前提下，能有效提高系统效率，证明了变转速定量泵压力控制系统的有效性与可行性。     

高背压等离子点火器及其液体燃料点火特性实验研究

航天应用的液体火箭发动机及燃烧型加热器燃烧室室压高、燃料流量大、温度低、有重复启动需求，实现安全可靠点火的难度较大。针对这些需求，研究了一种采用高背压设计的电弧等离子体点火器。实验研究了Ar，N₂气体工质在高进气压力下的伏安特性，发现N₂在宽压力范围内适用于点火。发射光谱分析表明，在高达数MPa的进气压力下，Ar，N₂等离子体射流电子密度符合局部热力学平衡判据（LTE判据），点火能量集中。N₂等离子体整体温度低于Ar，但阳极喷口附近温度高于Ar，N₂等离子体射流火焰长，卷吸沿程空气造成射流平均温度偏低，但有助于低温液体推进剂的蒸发混合和强化点火。等离子体射流引起了臭氧和氮氧化物的形成，具有促进点火和化学反应的作用。背压提高引起电源输出电压升高，提高供气压力和电流，有助于点火器在高背压环境中稳定电压。燃烧型空气加热器燃烧室的点火实验发现，采用N₂等离子体喷注面中心点火，可以在短时间内完成酒精-空气和酒精-液氧-空气的点火，最高燃烧室室压接近5MPa时，点火器仍能稳定工作，多次使用电极烧蚀不明显，在液体火箭发动机的重复可靠点火方面具有很好的应用前景。     

An empirical solar radiation pressure model for satellites moving in the orbit-normal mode

We present a family of empirical solar radiation pressure (SRP) models suited for satellites orbiting the Earth in the orbit normal (ON) mode. The proposed ECOM-TB model describes the SRP accelerations in the so-called terminator coordinate system. The choice of the coordinate system and the SRP parametrization is based on theoretical assumptions and on simulation results with a QZS-1-like box-wing model, where the SRP accelerations acting on the solar panels and on the box are assessed separately. The new SRP model takes into account that in ON-mode the incident angle of the solar radiation on the solar panels is not constant like in the yaw-steering (YS) attitude mode. It depends on the elevation angle of the Sun above the satellite’s orbital plane. The resulting SRP vector acts, therefore, not only in the Sun-satellite direction, but has also a component normal to it. Both components are changing as a function of the incident angle. ECOM-TB has been used for precise orbit determination (POD) for QZS-1 and BeiDou2 (BDS2) satellites in medium (MEO) and inclined geosynchronous Earth orbits (IGSO) based on IGS MGEX data from 2014 and 2015. The resulting orbits have been validated with SLR, long-arc orbit fits, orbit misclosures, and by the satellite clock corrections based on the orbits. The validation results confirm that—compared to ECOM2—ECOM-TB significantly (factor 3–4) improves the POD of QZS-1 in ON-mode for orbits with different arc lengths (one, three, and five days). Moderate orbit improvements are achieved for BDS2 MEO satellites—especially if ECOM-TB is supported by pseudo-stochastic pulses (the model is then called ECOM-TBP). For BDS2 IGSOs, ECOM-TB with its 9 SRP parameters appears to be over-parameterized. For use with BDS2 IGSO spacecraft we therefore developed a minimized model version called ECOM-TBMP, which is based on the same axis decomposition as ECOM-TB, but has only 2 SRP parameters and is supported by pseudo-stochastic parameters, as well. This model shows a similar performance as ECOM-TB with short arcs, but an improved performance with (3-day) long-arcs. The new SRP models have been activated in CODE’s IGS MGEX solution in Summer 2018. Like the other ECOM models the ECOM-TB derivatives might be used together with an a priori model.     

无刷双馈电机静止坐标系数学模型的研究

由于没有电刷和滑环,提高了运行的可靠性,降低了维护成本,因此无刷双馈电机(BDFM)在变速恒频发电领域有着广阔的应用前景。由于特殊的结构和工作原理,BDFM数学模型十分复杂。从BDFM多回路空间矢量数学模型出发,推导出了两个静止坐标系之间的坐标变换关系以及功率绕组静止坐标系数学模型和控制绕组静止坐标系数学模型,推导过程简洁明了。所得结果为BDFM理论分析和不同控制策略的研究提供了理论基础。MATLAB/Simulink环境下的仿真结果验证了数学模型及坐标变换关系的正确性。     

复杂动态环境下无人飞行器动态避障近似最优轨迹规划

针对复杂动态环境下无人飞行器的动态障碍规避问题，基于合理假设建立了无人飞行器和动态障碍的运动学模型，并综合考虑无人飞行器飞行过程中的终端约束、控制输入约束、安全避障约束等，以能量最少为性能指标构建动态避障问题数学描述。之后，针对终端约束和控制输入约束，依据优化模型预测静态规划算法(OMPSP)生成初始轨迹；针对动态避障问题的不等式约束，引入松弛变量并结合滑模变结构控制方法设计松弛变量动力学，实现对一个、多个或同时多个动态障碍的安全规避；最后，依据有限时间微分动态规划(RHDDP)算法进行轨迹优化，获得满足上述各种约束并能规避动态障碍的近似最优轨迹。     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

The adjusted optical properties for Galileo/BeiDou-2/QZS-1 satellites and initial results on BeiDou-3e and QZS-2 satellites

Solar Radiation Pressure (SRP) is the dominant non-gravitational perturbation for GNSS (Global Navigation Satellite System) satellites. In the absence of precise surface models, the Empirical CODE Orbit Models (ECOM, ECOM2) are widely used in GNSS satellite orbit determination. Based on previous studies, the use of an a priori box-wing model enhances the ECOM model, especially if the spacecraft is a stretched body satellite. However, so far not all the GNSS system providers have published their metadata. To ensure a precise use of the a priori box-wing model, we estimate the optical parameters of all the Galileo, BeiDou-2, and QZS-1 (Quasi Zenith Satellite System) satellites based on the physical processes from SRP to acceleration. Validation using orbit prediction proves that the adjusted parameters of Galileo and QZS-1 satellites exhibit almost the same performance as the corresponding published and “best guess” values. Whereas, the estimated parameters of BeiDou-2 satellites demonstrate an improvement of more than 60% over the initial “guess” values. The resulting optical parameters of all the satellites are introduced into an a priori box-wing model, which is jointly used with ECOM and ECOM2 model in the orbit determination. Results show that the pure ECOM2 model exhibits better performance than the pure ECOM model for Galileo, BeiDou-2 GEO and QZS-1 orbits. Combined with the a priori box-wing model the ECOM model (ECOM+BW) results in the best Galileo, BeiDou-2 GEO and QZS-1 orbits. The standard deviation (STD) of satellite laser ranging residuals reduce by about 20% and 5% with respect to the pure ECOM2 model for Galileo and BeiDou-2 GEO orbits, while the reductions are about 40% and 60% for QZS-1 orbits in yaw-steering and orbit-normal mode respectively. BeiDou-2 IGSO and MEO satellite orbits do not benefit much from the a priori box-wing model. In summary, we suggest setting up a unified SRP model of ECOM+BW for Galileo, QZS-1, and BeiDou-2 orbits based on the adjusted metadata. In addition, we estimate the optical parameters of BeiDou-3e and QZS-2 satellites using a limited number of tracking stations. Results regarding the unified SRP model indicate the same advantages, the STD of satellite laser ranging residuals reduces by about 30% and 20% for QZS-2 and BeiDou-3e orbits respectively over orbit products without a priori model. The estimation procedure is effective and easy to apply to the new emerging satellites in the future.     

工艺模型驱动的物料动态精准配送技术

针对飞机装配车间传统“领料式”物料配送存在的弊端,提出了一种工艺模型驱动的物料动态精准配送方法,构建了飞机装配车间物料精准配送管理系统,阐述了系统构建涉及的关键技术难点,采用基于模型的三维可视化消耗式BOM重构方式,建立与设计了模型动态同步精准的MBOM工艺模型,利用RFID技术的优点实时获取物料信息,通过iGPS系统引导AGV物料运输平台来实现装配站位物料的高精度配送。     

熔融沉积成型连续碳纤维增强尼龙蜂窝芯材的压缩特性

采用熔融沉积成型方法成形了连续碳纤维增强尼龙复合材料蜂窝芯材,并对不同测试方向的静态单轴压缩特性进行了表征分析,着重关注不同测试方向熔融沉积成形蜂窝芯材平面静态压缩破碎行为和能量吸收行为,并与纯聚合物基体进行对比。结果表明:X_1方向的压缩平台区域的力-位移曲线更加平滑稳定,且载荷值稍高于X_2方向,因此X_1方向更适用于能量吸收应用;此外,连续纤维的增强作用可使蜂窝芯材的平台载荷值得到明显提升。研究结果为连续纤维增强聚合物复合材料的空间增材制造提供理论基础。