连续式风洞二喉道调节马赫数控制策略

为了降低连续式跨超声速风洞压力波动,提高马赫数稳定性,需要对二喉道调节马赫数控制方式进行研究,针对现有文献鲜少对该控制策略描述等问题,以0.6m连续式跨声速风洞为例,对二喉道控制马赫数的原理进行分析,基于运动控制器加伺服驱动器双PID(proportion-integral-derivative)控制模式实现二喉道位置精确控制,提出了二喉道和压缩机转速的组合控制流程,并采用分段变参数模糊PID加串级控制的算法实现马赫数精确控制,最后进行了试验验证。结果表明马赫数控制精度优于0.001,且每个马赫数极曲线(9个攻角阶梯)的时间可控制在4min以内,证明所提出的控制策略是有效的,可为连续式跨超声速风洞的设计调试提供参考。      

Ground experiments of Chang’e-5 lunar regolith penetrating radar

The Lunar Regolith Penetrating Radar (LRPR) is an Ultra-Wideband (UWB) array-based Ground penetrating radar (GPR) onboard the lander of Chang’e-5 (CE-5) mission. The primary scientific objectives of the LRPR are to probe the thickness and structure of lunar regolith of the landing site, and support the drilling and sampling process. In order to evaluate the performance of the LRPR, a series of ground experiments are performed using the LRPR prototype mounted on a CE-5 lander model. The performance of the LRPR is evaluated by comparing the experimental data with the simulated data. Data processing and imaging method are verified, and the interferences from the lander and other aspects are analyzed. The results of the ground experiments and simulation demonstrate that the LRPR is able to meet the design requirement of 2-m detection depth. They also indicate that the upper and lower interfaces of the stratified structure in the lunar regolith can be well distinguished by the LRPR when the dielectric constant difference is greater than 0.3, and the imaging effect of the location under the dense antennas is better than that of other positions. However, the identification capability of the LRPR to the independent blocky objects is relatively poor mainly due to the clutters caused by the lander, the sparsity of the antenna elements compared to the size of the basalt block, the limited aperture of the antenna array, and the tail of the transmitted waveform.     

全模颤振风洞试验三索悬挂系统多体动力学分析

全模颤振风洞试验需要通过软支撑系统模拟飞行器的自由飞行状态并调整模型姿态达到配平状态。参考NASA双索悬挂方案，提出了一种两电机驱动的三索悬挂系统，利用后方两索的同向/反向联动实现模型俯仰和滚转姿态的调整，利用弹簧刚度以及钢绳张力设计实现支撑频率要求。基于柔性多体动力学方法，建立了包括飞行器刚体模型、柔性索、滑轮、弹簧、气动力模型、伺服电机控制在内的复杂系统动力学模型，其中，利用任意拉格朗日-欧拉（ALE）变长度索单元描述钢绳，利用不约束物质坐标的索结点约束描述钢绳与滑轮相互作用，利用索结点物质输运速度约束描述伺服电机绞盘，利用飞行力学的气动力模型描述吹风下的气动力。基于该模型，通过小扰动响应辨识研究了弹簧刚度、钢绳张力、连接点位置等因素对支撑频率的影响规律，并分析了系统姿态调整能力，俯仰调整范围达到-12.5°~12.5°，滚转调整范围达到-45°~45°。采用滑轮处电位计测量的钢绳相对位移作为反馈信号，基于设计的控制律利用多体动力学求解器与Simulink对风洞吹风下的姿态调整过程进行仿真，模型达到配平状态，获得了吹风下的索拉力和伺服电机功率，为系统设计提供基础。     

Remote-controlled flexible pose measurement system and method for a moving target in wind tunnel

The measurement of position and attitude parameters for the isolated target from a high-speed aircraft is a great challenge in the field of wind tunnel simulation technology. This paper proposes a remote-controlled flexible pose measurement system in wind tunnel conditions for the separation of a target from an aircraft. The position and attitude parameters of a moving object are obtained by utilizing a single camera with a focal length and camera orientation that can be changed based on different measurement conditions. Using this proposed system and method, both the flexibility and efficiency of the pose measurement system can be enhanced in wind tunnel conditions to meet the measurement requirements of different objects and experiments, which is also useful for the development of an intelligent position and attitude measurement system. The position and the focal length of the camera also can be controlled remotely during measurements to enlarge both the vertical and horizontal measurement range of this system. Experiments are conducted in the laboratory to measure the position and attitude of moving objects with high flexibility and efficiency, and the measurement precision of the measurement system is also verified through experiments.     

前缘缝翼构型平尾直升机气动特性分析

使用数值模拟方法研究了前缘缝翼翼型气动特性,并将该前缘缝翼翼型应用于直升机平尾,分析了该直升机全机气动特性,最后通过风洞试验对数值模拟结果进行验证。结果表明,前缘缝翼构型平尾能有效改善直升机的纵向静稳定性。     

基于单应性矩阵的模型迎角单目视频测量方法

风洞试验中模型迎角的精准测量是降低阻力系数误差的重要途径之一，为此，提出了基于单应性矩阵的模型迎角单目视频测量方法。该方法通过两个单应性矩阵，获取试验过程中相机实时位姿和标记点物方空间位置坐标，应用坐标旋转关系，完成试验模型的迎角测量。数值仿真试验结果表明：迎角测量误差与待测标记点到风洞壁板间的距离偏差近似为线性关系，因此，当标记点不满足共面条件时，可根据该特点进行测量误差修正。静态标定和风洞迎角测量试验结果表明：修正系统误差后，迎角实测数据的测量准度在0.01°以内，精度不超过0.012°。本文方法易于实施，工程实用价值强。     

高超声速圆锥边界层失稳条纹结构实验研究

边界层转捩的准确预测是高超声速飞行面临的关键气动问题之一。为研究高超声速边界层失稳和转捩机理,以前缘半径1.6mm、半锥角7°的圆锥模型为研究对象,在FD-07高超声速风洞中采用红外热图技术开展边界层转捩实验测量。通过与工程计算结果对比,确认模型表面边界层流态。实验结果表明:有迎角条件下,模型表面中后段出现条纹结构,条纹结构的起始位置随着周向角的增加而向上游移动;随着迎角的增加,条纹起始位置向上游移动,条纹强度差异和条纹与模型中心线的夹角越来越大。实验获得的条纹结构与不同频率扰动波相互作用直接数值模拟获得的条纹结构现象一致。通过对比分析,认为边界层内不同频率扰动波相互作用是产生条纹结构的一种机制。     

某飞行器推力矢量试验测力装置研制

为满足某飞行器推力矢量试验的测试要求,采用两台六分量应变天平和一个空气桥组成测力装置来实现飞机全机气动力和喷管推进特性同时分别测量。基于有限元软件,对天平的应变及空气桥对天平的干扰进行了分析。结果表明:空气桥对天平力分量的干扰值优于5%,对力矩(滚转力矩除外)分量的干扰值优于15%,达到了设计指标。通过校准获得了单独天平、天平带空气桥(充压、不充压)状态下的校准公式,校准结果表明:两台天平各分量的综合加载误差均优于0.3%,天平带空气桥(充压、不充压)状态下各分量的综合加载误差优于0.5%,空气桥对天平的干扰量值与有限元分析结果一致。理论分析与实测结果证明:研制的天平及空气桥达到了预定目标,它的测量精准度高,满足推力矢量风洞试验需求。     

民机飞行结冰参数的模拟与校准

结冰问题的研究对于民用飞机设计十分重要,采用结冰风洞试验是主要的方法之一,欧美国家有很多成熟的结冰风洞用于型号研究。结冰风洞中需要对很多参数进行控制,其中水雾参数精确控制的难度很大,而且一般通过间接方法来进行测试校准,往往误差较大,导致不同结冰风洞试验结果往往有所差异。文章介绍了在意大利宇航中心的IWT 结冰风洞完成的冰风洞校准试验,对结冰风洞水雾参数校准方法进行了阐述,为民机结冰风洞研究提供参考。     

等离子体对翼型流动分离控制历程的PIV试验研究

采用粒子图像测速（Particle Image Velocimetry,PIV）技术,研究了介质阻挡放电等离子体激励对NA—CA0015翼型表面流动分离的控制特性及控制效果随时间历程的变化规律。结果表明,激励电压存在一个阈值,当电压小于阈值时,控制无效或效果不明显;当电压接近阈值时,控制表现出不稳定性并最终趋于稳定;当电压大于阈值时,控制效果稳定且显著,气流能够很好地重附在翼型表面。