叶片式预旋喷嘴出口流场实验研究

叶片式预旋喷嘴具有尺寸小,落后角大的特点。为了详细研究小尺寸预旋喷嘴的预旋性能,采用五孔探针对叶片式预旋喷嘴的出口流场进行了实验研究。测量了Ma=0.2,0.3时喷嘴出口的压力分布、速度分布和出口气流角度分布,实验获得了喷嘴的落后角和预旋效率,并进行了与实验工况相同的数值计算。通过实验获得的总压云图以及速度云图,可以发现叶片式预旋喷嘴的端壁二次流损失、尾迹损失严重,有明显的边界层分离现象。Ma=0.2时,喷嘴Re数为5.76×104,落后角2.84°,实验测得的预旋效率为0.73;Ma=0.3时,喷嘴Re数为1.06×105,预旋效率提高至0.77。实验模型端壁的影响使预旋效率实验结果偏低6.5%左右。数值结果与实验测得各参数符合较好:数值结果与测得的喷嘴出口截面平均总压、静压偏差在1%以内;出气速度、周向速度以及出气角度与实验结果偏差在4%以内。数值计算表明,叶片式预旋喷嘴的预旋效率基本不受压比影响,随Re数增大先增大后基本不变,最后基本稳定在0.85。     

逆向进气复合角发散冷却孔流量系数试验

针对回流燃烧室外环壁面冷气与燃气流动方向相反的情况,试验研究了发散孔进气方向与环腔通道气流流动方向相反的条件下,复合角发散冷却孔流量系数随发散孔倾角(25°~55°)、偏角(90°~180°)及压降系数等参数的变化规律。研究结果表明:复合角发散孔的流量系数随倾角的增大而增大,随偏角的增大而减小；随着压降系数的增大,复合角发散孔的流量系数先呈近似线性增长,当压降系数大于0.95后,呈非线性增长且增长速度减缓。      

基于双环滑模控制的直/气复合控制系统设计

直/气复合控制导弹具有强干扰、强非线性以及强耦合等特点，传统的姿态控制器难以适用于该种复杂干扰并存的情况，文章提出了基于双环滑模控制的直/气复合控制器。首先采用有限时间收敛趋近律分别构造内外环滑模控制器，并将角速度回路的滑模变量量化为直接力指令，以解决空气舵与姿控发动机之间的耦合问题。接着使用非线性扩张状态观测器估计综合干扰，从而设计控制器补偿侧向喷流干扰及模型不确定性等综合干扰的影响。然后基于李雅普诺夫方法证明了控制系统闭环稳定，分析了干扰补偿对控制器收敛域的影响。最后仿真结果表明，该方法跟踪速度快，动态过程平稳，具有较强的干扰抑制能力，具有很强的鲁棒性。     

考虑捷联导引头最小视场角约束的制导策略

针对高超声速飞行器捷联导引头，提出导引头最小视场角（FOV）约束问题。首先分析了导引头视线角变化规律，指出在攻击固定目标时，导引头最小视场角约束在弹道末段无法被满足，导引头将丢失目标。在此基础上，基于缩短导引头丢失目标距离的目标，提出一种满足导引头最小视场角约束的制导策略。该策略不依赖于末制导律形式，当最小视场角约束无法被满足时，改变原有制导指令，主动改变弹道轨迹以增加弹体视线角，避免超出视场范围。其次，针对飞行器过载约束，设计了制导策略切换点，在到达切换点时该制导策略将结束工作，避免末端过载过大超出约束。通过对比仿真验证了所提出制导策略有效性，能够大幅度减少导引头丢失目标距离，工程上有利于提高末端命中精度。     

Application of improved active disturbance rejection control algorithm in tilt quad rotor

The Tilt Quad Rotor (TQR) has complex dynamics characteristics, especially in conversion mode. It is difficult to build the dynamic model of the TQR and the environmental factors have a great influence on it. To solve the problem of control in conversion mode of TQR, this paper carries out the design of the controller based on improved Active Disturbance Rejection Control (ADRC). According to the characteristics of flight in conversion mode, Tracking Differentiator (TD) with explicit model is used to solve the problem of multiple integrals when the system is high-order system. Extended State Observer (ESO) with Radial Basis Function (RBF) neural network is used to estimate and compensate for internal and external uncertainties, and the adaptive sliding mode control in Nonlinear State Error Feedback (NLSEF) is used to improve the response speed of the controller and reduce the parameters which should be tuned. Through the flight control simulation of the TQR, the validity and rationality of the control system are verified.     

Statistical characteristics of low latitude Pc4s: Influence of solar wind and IMF parameters

Pc4 signatures for the year 2013, extracted from geomagnetic north–south and east–west components of induction coil magnetometer (LEMI 30) from low latitude station Desalpar (DSP), operated by Institute of Seismological Research (ISR), India have been investigated vis-à-vis the prevalent interplanetary parameters (IMF) as well as the geomagnetic activity indices. A clear dominance of Pc4-5 (467 events) over Pc3 (17 events) is observed. Local time variation of Pc4 shows a peak in the noon sector in both X and Y components. Our investigations show that the dominant peak frequency is 10 mHz at low latitude region. Correlations with solar wind and IMF parameters illustrate highest occurrence of Pc4 for a solar wind speed of 300–400 km/s and average IMF B field of 3–6 nT. The amplitude of Pc4s at DSP shows an increase with increasing solar wind speed, plasma density, solar wind dynamic pressure and average B field which is also reflected in the trend of frequency variation of these pulsations. We report that IMF clock angle at low latitude does not have influence on Pc4 occurrence. Based on the characteristics of these events, detected in latitudinally distributed stations from low and mid-latitudes from northern and southern hemisphere, we infer that modes were compressional, which could be driven by K-H instability or solar wind dynamic pressure, as compressional modes can propagate to low latitude with little attenuation.     

基于微型涡喷发动机热喷流的无源流体推力矢量喷管的控制规律

流体推力矢量喷管型面固定、活动部件少、结构重量轻，能够为高机动飞行器提供有效的飞行控制手段，但无源流体推力矢量喷管热喷流的偏转控制规律尚未完全掌握。为了推进无源流体推力矢量技术的实用化，本文设计研制了适用于微型涡喷发动机的耐高温喷管模型，对该喷管在微型涡喷发动机热喷流状态下的控制规律进行研究。利用非接触光学显示和测量手段——红外热成像拍摄和粒子图像测速（PIV）技术对主射流流动特性进行研究，获得流动矢量角随二次流控制阀门闭合度变化的控制规律；利用六分量盒式天平测力实验研究无源流体推力矢量喷管的力学特性，获得推力矢量角随二次流控制阀门闭合度变化的控制规律。研究结果表明：该构型喷管在微型涡喷发动机热喷流下主射流连续可控偏转，最大流动矢量角为-12.3°/12.3°，最大推力矢量角为-12.9°/12.8°，控制规律接近线性，不存在主射流偏转突跳问题。     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

先进战斗机过失速机动大气数据融合估计方法

可控的过失速机动是先进战斗机超机动性能的重要标志，飞机飞行包线的扩大已超出传统的大气数据系统测量范围，可靠的迎角、侧滑角、总压、静压等飞行大气数据是制约先进战斗机过失速机动中飞行控制的关键因素。以中国推力矢量验证机为对象，基于过失速机动飞行试验的数据，开展大气参数估计与验证研究。结合过失速机动的时间与空间特性，研究了基于风速、地速、空速矢量和惯性姿态、导航参数的大气参数融合计算方法；针对过失速大迎角状态下飞机周围气流非定常、模型非线性导致的融合大气参数误差的复杂特性，进一步构建深度神经网络，对机动状态融合迎角、侧滑角的强非线性误差进行拟合。仿真和飞行试验表明：该方法可在大迎角飞行状态下实现主要大气参数的融合估计，过失速机动过程中融合迎角误差优于2.3°，融合得到的大气参数可为过失速大迎角机动飞行控制提供可靠的大气参数状态反馈。