全文获取类型
收费全文 | 158篇 |
免费 | 22篇 |
国内免费 | 45篇 |
专业分类
航空 | 156篇 |
航天技术 | 30篇 |
综合类 | 22篇 |
航天 | 17篇 |
出版年
2023年 | 1篇 |
2022年 | 3篇 |
2021年 | 7篇 |
2020年 | 10篇 |
2019年 | 10篇 |
2018年 | 10篇 |
2017年 | 9篇 |
2016年 | 18篇 |
2015年 | 13篇 |
2014年 | 12篇 |
2013年 | 7篇 |
2012年 | 16篇 |
2011年 | 22篇 |
2010年 | 10篇 |
2009年 | 13篇 |
2008年 | 13篇 |
2007年 | 15篇 |
2006年 | 10篇 |
2005年 | 3篇 |
2004年 | 4篇 |
2003年 | 2篇 |
2002年 | 1篇 |
2001年 | 5篇 |
2000年 | 1篇 |
1999年 | 1篇 |
1997年 | 1篇 |
1994年 | 1篇 |
1993年 | 3篇 |
1992年 | 1篇 |
1991年 | 1篇 |
1990年 | 1篇 |
1988年 | 1篇 |
排序方式: 共有225条查询结果,搜索用时 15 毫秒
1.
航空航天难加工材料直纹面构件的高精度高表面完整性加工已经成为制造领域普遍关注和亟需解决的难题,电解线切割加工在高表面完整性要求加工场合上具有原理性优势。建立脉冲电流电解线切割加工模型,分析了工件厚度变化带来的影响。试验结果表明:随着工件厚度增加,电解液电阻减小,工件两端极间电压减小,加工缝宽变窄;双电层时间常数增大,脉宽时间内充电所能达到的电位降低,有效加工时间变短,平均电流密度较低;脉冲频率大于20 kHz时,最大进给速度随频率增加而快速减小,低于20 kHz时,最大加工速度差别较小。最后,采用脉冲频率20 kHz,以进给速度4 μm/s稳定加工出20 mm厚榫头/榫槽结构,表面粗糙度约为0.449 4 μm,表面质量、加工效率明显高于100 kHz加工效果。 相似文献
2.
为解决小半径弯管内侧起皱、外侧减薄的成形缺陷,提出了一种弯胀复合成形的方法。通过几何关系解析了初始弯曲半径和初始管坯直径与最终管径和最终弯曲半径之间的关系,确定了初始弯曲半径的取值范围。采用有限元与实验相结合的方式研究了不同初始弯曲半径对零件壁厚分布的影响,分析了胀形过程中零件弯曲处及直壁处的变形规律。最终发现:初始弯曲半径越大,零件的最终减薄越小,胀形过程中弯曲处内外侧发生均匀减薄,直壁处内侧减薄明显大于外侧减薄。 相似文献
3.
分析了在胶粘剂剪切强度检测过程中,胶接材料表面处理方法、胶层的厚度、测试时加的垫片厚度和试样的夹距距离、涂胶时的晾置时间等因素对检测结果影响。研究结果表明,上述因素不仅直接影响了胶粘剂粘接强度的大小,而且关系到胶粘剂剪切强度检测试验的测试结果。 相似文献
4.
5.
6.
7.
8.
CHEN Guodinga SUN Hengchaoa WANG Junb aSchool of Mechanical Engineering Northwestern Polytechnical University Xi’an China bAVIC Commercial Aircraft Engine Co. Ltd Shanghai China 《中国航空学报》2011,(3):355-362
The lubrication design and heat transfer determination of bearing chambers in aeroengine require a sufficient understanding of the oil droplet-film interaction and physical characteristic in an oil/air two-phase flow state.The analyses of oil droplet movement,mass and momentum transfer during the impingement of droplet/wall,as well as wall oil film thickness and flow velocity are very important for the bearing chamber lubrication and heat transfer calculation.An integrated model in combination with droplet movement,droplet/wall impact and film flow analysis is put forward initially based on the consideration of droplet size distribution.The model makes a contribution to provide more practical and feasible technical approach,which is not only for the study of droplet-film interaction and physical behavior in bearing chambers with oil/air two-phase flow phenomena,but also useful for an insight into the essence of physical course through droplet movement and deposition,film formation and flow.The influences of chamber geometries and operating conditions on droplet deposition mass and momentum transfer,and wall film thickness and velocity distribution are discussed.The feasibility of the method by theoretical analysis is also verified by the existing experimental data.The current work is conducive to expose the physical behavior of wall oil film configuration and flow in bearing chamber,and also significant for bearing chamber lubrication and heat transfer study under oil/air two-phase flow conditions. 相似文献
9.
连续体结构拓扑优化方法评述 总被引:8,自引:2,他引:6
连续体结构拓扑优化在优化中能产生新的构型,对实现自动化智能结构设计具有重要意义。目前,连续体结构拓扑优化方法主要有:均匀化方法、变厚度法、变密度法、渐进结构优化方法、水平集法、独立连续映射方法。本文首先系统回顾了以上方法的发展历程,介绍了它们的研究现状。其次,通过对比以上拓扑优化方法对若干典型算例的优化结果,表明以上方法都有较好的减重效果。最后,对以上方法进行了总结,列出了它们的优缺点和发展方向。 相似文献
10.