A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

A multi-stage regulation strategy of space manipulators with a free-swinging joint failure

To ensure tasks can be completed after a free-swinging joint failure occurs, a multi-stage regulation strategy of space manipulators is proposed. Considering all terms of the dynamics equation, an evaluation model of the regulation ability (EMRA) of active joints over the fault joint is established based on the fuzzy entropy. And then a multi-stage regulation strategy based on the EMRA is designed to regulate the fault joint. The strategy divides the regulation process into several stages, and select a certain active joint to regulative the fault joint in every stage. With this multi-stage regulation strategy, the fault joint can be regulated to the desired angle without huge torque on regulative joints. The simulation is carried out with a 7-DOF space manipulator, verifying the correctness and effectiveness of the multi-stage regulation strategy. The strategy has three advantages: Coriolis and centrifugal terms are both considered for the first time in selecting the regulative joint, making the selection result more in line with the actual regulation process; The influence of the model uncertainty is eliminated in establishing the EMRA, making the evaluation of regulative ability more precise; The fault joint is successfully regulated to the desired angle without huge torque on regulative joints.     

飞秒激光系统图像调焦装置以及方法

飞秒激光直写技术在复杂三维微结构加工领域具有显著优势，而调焦是否精准直接影响了所加工结构的完整度.提出了在光路中临时置入调焦光源和物的图像调焦技术，通过调节物的位置使其成像面与激光聚焦面一致，从而通过清晰可分辨的成像状态间接反映激光聚焦状态.利用Zemax软件模拟分析了原飞秒激光光路与加入调焦光源和物的调焦光路，二者可实现相同加工物镜后工作距离与良好成像质量，证明了该方法的可行性.通过分析得到该过程的成像误差主要由成像镜头焦深(3.9 μm)引起，我们获得的理想调焦精度可达到1/2焦深以内.设计了单层高度为5 μm的二层圆柱结构，通过多次实验验证了所加工元件高度误差在1.5 μm范围以内，与理论分析一致，满足飞秒激光系统的调焦要求.     

Alfvén gravity waves in viscous solar plasma: Effect of the background flow

We study the Propagation and damping properties of Alfvén gravity waves in the presence of the vertical magnetic field in the viscous solar plasma under influence of the background flow by deriving a fourth order dispersion relation in terms of the Doppler shifted frequency. We derive the dispersion relation under WKB and Boussinesq approximation. We study the damping of Alfvén gravity waves for the wave frequencies less than and greater than the Brunt-Väisälä frequency. We find that the Brunt-Väisälä frequency divides the frequency ranges where the weakly or strongly damped oscillations occur. The background flow exhibits a strong effect on weakly damped oscillations and a weak effect on the strongly damped oscillations. We also notice that the damping of both the strong and weakly damped oscillations depend on the Brunt-Väisälä frequency and wave number. The effect of the background flow is also being governed by the Brunt-Väisälä frequency and wave number. We also study the properties of gravity wave mode after filtering the Alfvén wave mode by minimizing the magnetic field and noticed that the background flow shows a very strong effect on the gravity wave mode.     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

Evasion guidance algorithms for air-breathing hypersonic vehicles in three-player pursuit-evasion games

In practical combat scenario, the cooperative intercept strategies are often carefully designed, and it is challenging for the hypersonic vehicles to achieve successful evasion. Based on the analysis, it can be found that if several Successive Pursuers come from the Same Direction (SPSD) and flight with a proper spacing, the evasion difficulty may increase greatly. To address this problem, we focus on the evasion guidance strategy design for the Air-breathing Hypersonic Vehicles (AHVs) under the SPSD combat scenario. In order to avoid the induced influence on the scramjet, altitude and speed of the vehicle, the lateral maneuver and evasion are employed. To guarantee the remnant maneuver ability, the concept of specified miss distance is introduced and utilized to generate the guidance command for the AHV. In the framework of constrained optimal control, the analytical expression of the evasion command is derived, and the constraints of the overload can be ensured to be never violated. In fact, by analyzing the spacing of the pursers, it can be classified whether the cooperative pursuit is formed. For the coordination-unformed multiple pursers, the evasion can be achieved lightly by the proposed strategy. If the coordination is formed, the proposed method will generate a large reverse direction maneuver, and the successful evasion can be maintained as a result. The performance of the proposed algorithms is tested in numerical simulations.     

基于新型丝状电极等离子体激励器的前体涡控制

本文首次将新型丝状暴露电极DBD等离子激励器应用于大迎角下细长体非对称涡控制。丝状暴露电极的材料的选择对DBD推力以及推力效率至关重要,通过地面精细推力测量对丝状暴露电极等离子体激励器进行了优化,结果表明,本文研究材料中采用钨丝作为暴露电极,其推力效率最优;且随着电极直径从d=0.3 mm减小到d=0.08 mm,DBD推力效率显著提升。基于优化后的DBD激励器,将其应用于前体非对称涡控制:未施加等离子体控制时,压力测量以及PIV结果均表明细长体背风区流场为明显的非对称涡结构;在等离子体激励下,该非对称涡结构可变为对称甚至反向非对称,且非稳态激励控制能力明显优于稳态激励。研究发现,大迎角下细长体非对称涡控制与背风区原始涡系结构有关,其中包含对称涡系和非对称涡系。本文研究为大迎角下细长体非对称涡控制提供了一种新思路,同时也为丝状暴露电极DBD等离子体激励器的应用提供参考。     

电铸镍Wolter I型光学系统制造技术发展综述

摘要： 为满足未来脉冲星导航和空间天文观测任务对X射线望远镜的载荷需求，Wolter I光学系统的研制正逐渐成为新的研究热点，电铸镍方案是当前国内外X射线光学系统镜筒制造的主要技术方案.文章对电铸镍X射线光学系统制造工艺、国内外研制现状、未来应用需求进行了介绍和整理，梳理了电铸镍X射线光学系统研制遇到的关键技术和难点，提出了后续研究发展建议，以促进中国在 X射线脉冲星自主导航、空间探测领域的快速发展.     

直线模拟加载系统的研究进展与发展趋势

直线模拟加载系统是一种用于在实验室条件下模拟承载对象工作时所受直线负载力的半实物仿真系统，可用于模拟各类飞行器关键部件在工作过程中所受的气体阻力载荷。针对目前常用的机械式、电液式和电动式直线模拟加载系统，分析其基本加载原理和研究进展，结合自行研制的电动式直线模拟加载系统进行了深入探讨。针对多余力抑制方法的关键问题，详细论述了直线负载模拟器的结构补偿方法和控制策略。最后，展望了直线模拟加载系统的发展趋势，归纳了电动式直线模拟加载系统的高精度、大载荷发展方向。     

基于EM‑EKF的深空光学自主导航系统光轴偏差补偿算法

在深空探测任务中,光学自主导航的精度受导航敏感器件安装精度的影响较大。提出了一种基于期望最大化-扩展卡尔曼滤波(EM-EKF)的光学自主导航系统光轴偏差补偿算法。算法基于条件概率的思想,预先设定状态变量和观测量的统计特性参数,通过不断地最大化条件期望,得到出现概率最大的状态变量估值和光轴偏差参数估值。该算法可分为4步:EKF、固定区间平滑、求解条件期望和期望最大化,不断迭代即可得到光轴偏差估计值。以火星探测近火段为例进行仿真验证,经光轴偏差补偿后,导航精度由100 km提升至20 km以内。