A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

Alfvén gravity waves in viscous solar plasma: Effect of the background flow

We study the Propagation and damping properties of Alfvén gravity waves in the presence of the vertical magnetic field in the viscous solar plasma under influence of the background flow by deriving a fourth order dispersion relation in terms of the Doppler shifted frequency. We derive the dispersion relation under WKB and Boussinesq approximation. We study the damping of Alfvén gravity waves for the wave frequencies less than and greater than the Brunt-Väisälä frequency. We find that the Brunt-Väisälä frequency divides the frequency ranges where the weakly or strongly damped oscillations occur. The background flow exhibits a strong effect on weakly damped oscillations and a weak effect on the strongly damped oscillations. We also notice that the damping of both the strong and weakly damped oscillations depend on the Brunt-Väisälä frequency and wave number. The effect of the background flow is also being governed by the Brunt-Väisälä frequency and wave number. We also study the properties of gravity wave mode after filtering the Alfvén wave mode by minimizing the magnetic field and noticed that the background flow shows a very strong effect on the gravity wave mode.     

反推装置对翼身融合分布式推进系统气动性能影响数值模拟

为了研究新型反推装置对翼身融合分布式推进系统气动性能的影响,将机身简化为二维模型,利用数值模拟的手段来研究攻角、反推开度,以及风扇打开或关闭对飞行参数的影响,为翼身融合分布式推进系统的反推装置设计提供初步的意见和建议。结果显示:反推闭合和风扇打开之后该机型的升力系数和俯仰力矩系数都会有较大增加;随着反推开度的增加,升力系数和俯仰力矩系数也随之增加;来流攻角对翼身融合分布式推进系统的气动性能也有较大影响。      

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

基于HHT的航空直流串行电弧特征提取方法

由于飞机内部布线空间有限、电弧故障存在发生时间地点随机以及特征不明显等问题，导致检测困难。本文基于航空270 V高压直流（HVDC）系统开展直流串行电弧故障特征提取方法研究，采用希尔伯特黄变换（HHT）提取电弧电流交流分量的时域和频域特征量。选择HHT的固有模态函数IMF5瞬时幅值的峰峰值和标准差作为识别电弧故障的时域特征，与原始信号中提取的时域特征量对比，正常和电弧特征量的区分度更大；选择HHT的固有模态函数IMF1+IMF2、一定频带范围内的瞬时幅值计算得到的谐波功率和作为区分正常和电弧情况的频域特征量。与常用的快速傅里叶变换（FFT）方法相比，HHT三维时频谱能够反映信号的局部特征，HHT方法计算得到的正常和电弧特征量之间的区分度更大，电弧和正常特征量的比值最高可达346。基于HHT的电弧故障特征提取方法能够更好地区分正常和电弧情况，有助于提高电弧故障的检测率，降低虚警率，具有重要的工程应用价值。     

逆向进气复合角发散冷却孔流量系数试验

针对回流燃烧室外环壁面冷气与燃气流动方向相反的情况,试验研究了发散孔进气方向与环腔通道气流流动方向相反的条件下,复合角发散冷却孔流量系数随发散孔倾角(25°~55°)、偏角(90°~180°)及压降系数等参数的变化规律。研究结果表明:复合角发散孔的流量系数随倾角的增大而增大,随偏角的增大而减小；随着压降系数的增大,复合角发散孔的流量系数先呈近似线性增长,当压降系数大于0.95后,呈非线性增长且增长速度减缓。      

基于新型丝状电极等离子体激励器的前体涡控制

本文首次将新型丝状暴露电极DBD等离子激励器应用于大迎角下细长体非对称涡控制。丝状暴露电极的材料的选择对DBD推力以及推力效率至关重要,通过地面精细推力测量对丝状暴露电极等离子体激励器进行了优化,结果表明,本文研究材料中采用钨丝作为暴露电极,其推力效率最优;且随着电极直径从d=0.3 mm减小到d=0.08 mm,DBD推力效率显著提升。基于优化后的DBD激励器,将其应用于前体非对称涡控制:未施加等离子体控制时,压力测量以及PIV结果均表明细长体背风区流场为明显的非对称涡结构;在等离子体激励下,该非对称涡结构可变为对称甚至反向非对称,且非稳态激励控制能力明显优于稳态激励。研究发现,大迎角下细长体非对称涡控制与背风区原始涡系结构有关,其中包含对称涡系和非对称涡系。本文研究为大迎角下细长体非对称涡控制提供了一种新思路,同时也为丝状暴露电极DBD等离子体激励器的应用提供参考。     

基于变马赫数的五孔探针三维插值方法

探讨了五孔探针气动数据的插值方法,为提高插值精度,开发了基于传统线性插值法的三维线性插值法。该方法把同一探针在不同马赫数下的校准图形成三维数据库,将实验数据通过三维图进行插值。并使用改进前后的两种插值方法分别对校准风洞测得的数据进行整理,对比结果证明:在实验工况连续变化的情况下,三维线性插值法在插值精度上要优于传统线性插值法。特别是在来流马赫数变化较大时,该方法可以改善单一校准文件处理造成的数据精度问题,可用于自动化流场采集系统,为流场高速高精度采集奠定基础。     

Implementation of tactical maneuvers with maneuver libraries

This study creates and combines the general maneuver libraries for fixed-wing aircraft to implement tactical maneuvers. First, the generalized maneuver libraries are established by analyzing the characteristics of tactical maneuvers required in battlefields. The 7th order polynomial is applied to both the creation of the maneuver libraries and the generation of the trajectories or flight paths for modal inputs. To track the desired trajectory, we design the Attitude Command Attitude Hold (ACAH) system and the Rate Command Rate Hold (RCRH) system using Model Following Controller (MFC). Moreover, the Line-of-Sight (LOS) guidance law is designed. In particular, the CONDUIT® is employed to optimize the gains so that the control systems meet the aircraft Handling Qualities (HQ) criteria. Finally, flight simulations are performed for the longitudinal loop, immelmann-turn, and climb-slalom-descent maneuvers to verify that tactical aggressive maneuvers are realizable via the combination of maneuver libraries. This study can contribute to the development of flight techniques for aircraft tactical maneuvers and to the revision of air force operational manuals.     

不同迎角下脊形前体绕流数值模拟研究

脊形前体有较强的背风涡流场,不同的前体形状对前体涡流场和气动力有很大的影响。本文针对脊形前体飞行器大迎角湍流大分离流动计算的困难,采用IDDES混合湍流模型,以及与之匹配的非定常算法,研究了不同来流迎角下脊形前体的气动特性,以及背风涡非定常演化、破裂的细致流动结构。选取了不同脊形角,以及不同上、下高宽比的脊形前体进行计算。计算结果表明,在迎角较小时,随着迎角的增大,前体主涡会逐渐增强,在迎角较大时,前体主涡破裂;在相同迎角下,脊形角较小时,前体涡较强,涡升力也更大;对于相同脊形角的前体,当上半截面高宽比较小时,前体主涡强度较大,前体涡破裂临界迎角较小,即会提前破裂。