Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

FOD缺口型损伤对TC4疲劳极限强度的影响

针对TC4钛合金风扇/压气机叶片前缘常遭受的外物损伤(FOD)缺口型损伤,进行了不同冲击角度下高速弹道冲击试验研究、损伤特征与应力集中分析,开展了冲击后不处理和冲击后去残余应力退火试样的高循环疲劳试验和疲劳极限强度预测。结果表明:随着冲击角度的增大入射侧损伤尺寸和应力集中系数基本保持不变,出射侧缺口损伤深度和损伤长度减小。损伤深度范围为0.6~1.5mm,应力集中系数范围为2.6~3.4。缺口型损伤试样的疲劳极限强度下降为光滑试样的27%~53%,与应力集中系数并不是呈反比关系。退火试样的高循环疲劳(HCF)性能或略微下降或基本不变,表明残余应力影响较小,残余应力对疲劳极限强度的影响程度不足光滑试样的10%。缺口型损伤试样的HCF性能与损伤底部半径的相关性不明显,随着最大损伤深度和损伤长度的增加而下降,表明制定维修手册时应着重考虑缺口型损伤的最大深度和损伤长度。Peterson经验公式对HCF性能的预测精度不理想,误差最大为45%,需要发展高精度的FOD缺口型损伤构件HCF性能预测方法。      

串联式TBCC发动机风车冲压模态性能模拟

建立了基于部件低转速特性匹配的串联式涡轮基组合循环（TBCC）发动机风车冲压模态性能计算模型，提出了压气机低转速大流量特性扩展方法，由换算扭矩代替等熵效率表示旋转部件特性，解决了低转速部件效率不连续相关问题。分析了冲压外涵面积变化和涡轮功率提取对风车冲压模态性能及部件匹配的影响规律，并基于推力、流量连续准则设计了涡轮模态至冲压模态转换过程（含风车冲压模态）的参数调节规律。计算结果表明:在风车冲压模态下，冲压外涵面积变化对风扇工作状态有显著影响，对压气机影响较小；涡轮可提取功率随着风车转速的减小先增加后降低，比冲随提取功率的增加基本呈线性降低趋势，功率提取位置（高、低压涡轮）对部件匹配有显著影响。      

大型飞机机身垂直入水冲击特性数值研究

针对带有中央翼盒的某型飞机的机身,数值研究了不同入水速度、姿态角和尾翘角对入水过程中机身压强和冲击力的影响规律。数值模拟中,控制方程选为非定常可压缩流动的雷诺时均Navier-tokes方程(RANS)和实现的k-ε模型,使用体积分数(VOF)方法捕捉水气交界面的变化,采用整体动网格技术来模拟机身相对于水面的运动。结果分析表明:机身入水过程中压强峰值首先出现在喷溅根部,随后转移至机身底部;入水初期机身冲击力系数迅速增大,而后略有回落,入水后期由于中央翼盒冲击水面会导致冲击力系数再次迅速增大,而后小幅震荡。速度越大、姿态角越大、尾翘角越小,机身冲击力系数越小。     

不同密度弹丸对水冰的超高速撞击成坑实验

为了研究冰冻天体表面撞击坑的形成与演化，开展了水冰的超高速撞击成坑实验。使用二级轻气炮发射1.0 mm直径的球形弹丸，以3 km/s、5 km/s和7 km/s速度对圆柱状冰块进行撞击。弹丸材料包括聚碳酸酯和不锈钢两种，冰块温度为253 K。实验观察到了不同弹丸和不同速度条件下，冰块中撞击坑的形貌特征。对撞击坑直径、深度和剖面形状进行了测量，并与文献中铝弹丸对水冰的撞击坑进行了比较分析。获得了水冰撞击坑特征随撞击参数的变化规律，结果表明：撞击坑直径和深度的主导机制不同，坑深主要由弹丸侵彻作用形成，而坑径主要由冰块的剥落所致；坑深比坑径具有更强的对于弹丸密度的依赖性，高密度弹丸撞击坑直径具有比低密度弹丸更强的对于撞击速度的依赖性；撞击坑体积与撞击能量成正比，高密度弹丸形成的撞击坑直径表现出“能量缩比”行为，而低密度弹丸形成的撞击坑直径表现出“动量缩比”行为。     

数字全息测量超高速撞击碎片云实验研究

在中国空气动力研究与发展中心(CARDC)超高速碰撞中心(HIRC)7.6 mm超高速碰撞设备的基础上，搭建纳秒级脉冲激光数字全息系统。提出滤波片和衰减片组合布置，减弱超高速碰撞等离子体自发光、提高信噪比的方法。实验获得了2.25 mm铝球弹丸以4.0 km/s的速度撞击0.5 mm厚铝板形成碎片云的全息图。采用小波变换算法对碎片云全息图进行重建，得到超高速撞击碎片云的三维结构和碎片大小。碎片云的轮廓呈椭球型，分为碎片云的前端、核心和外壳，碎片主要分布在弹丸破碎形成的碎片云核心，存在大碎片，且分布较集中，对后板的损伤也严重     

类蛛网状盘式谐振微陀螺的抗冲击性能与结构误差仿真分析

具有导航级潜能的盘式谐振微陀螺是国际研究最热门的一类微机械陀螺,在此基础上设计了一款频率裂解小的类蛛网状盘式谐振微陀螺。通过有限元仿真软件进行了模态分析和冲击分析,仿真结果表明类蛛网状盘式谐振微陀螺工作模态与寄生模态最小频差为3.9kHz,可承受的冲击载荷加速度高达25000g。此外,开展了晶向误差和工艺误差等结构误差对频率裂解影响的仿真研究,结果表明,其比圆环状盘式谐振陀螺在频率裂解上具有更低的结构误差敏感度。综上说明该结构能有效抑制寄生模态干扰、抗冲击性能强且结构误差鲁棒性好,具有较好的发展前景。     

极低压下两相流挤压油膜阻尼器油膜参数特性

针对极低供油压力工况开展实验研究,以考察气液两相流对挤压油膜阻尼器(SFD)油膜参数特性的影响。结果表明:当SFD入口气体体积分数小于0.9时,油膜阻尼随着入口气体体积分数的增加而减小,直至气体体积分数增大到0.9时,油膜阻尼是纯油状态时阻尼的60%;当气体体积分数大于0.9时,油膜阻尼大幅减小至几乎可以忽略不计。现有理论模型并不适用于极低供油压力工况。基于实验结果,找到了最符合SFD两相流动的等效黏度模型,其理论预测的油膜阻尼与不同供油压力下的实验数据吻合较好,为SFD两相流研究的模型选择提供了依据。     

基于纯比例导引的拦截碰撞角约束制导策略

拦截碰撞角约束制导是当前导弹制导研究的关键问题之一。首先基于理想比例导引（IPN）律拦截非机动目标的解析解,推导了纯比例导引律（PPN）拦截固定目标的解析解,得到了弹目相对距离、制导指令加速度和导弹前置角的显示表达式,并进一步得到了拦截碰撞角与弹目相对运动状态和比例导引系数之间的解析表达式。其次,基于该解析表达式,提出了基于PPN的拦截碰撞角约束制导策略（PPNIACG）,并探讨了在铅垂面内进行落角约束打击和水平面内进行拦截碰撞角约束打击的2种实现方式。最后,以弹道成型制导律（TSG）和最优碰撞角约束制导律（OIACG）为参考,通过数值仿真算例,对PPNIAC的拦截性能进行了对比分析,验证了所提出制导策略的有效性和正确性。