半球谐振子疲劳寿命分析与仿真

半球谐振子的寿命和损伤是直接影响高精度半球谐振陀螺使用时长和安全性的重要因素。目前国内加工的半球谐振子所用的熔融石英玻璃材料主要依靠进口，采用传统的疲劳寿命实验确定方法成本过于昂贵，因此需要利用疲劳分析软件对半球谐振子的疲劳寿命进行分析。文章通过半球谐振陀螺应力分析，采用ANSYS软件对熔融石英半球谐振子进行应力分析仿真，确定因残余应力所引起的疲劳危险部位，并在疲劳部位进行裂纹扩展分析，得到 、 和 型应力强度因子，以使在半球谐振子结构设计和使用过程中对易疲劳的部位进行有效监控和预防。     

A two-step robust adaptive filtering algorithm for GNSS kinematic precise point positioning

In kinematic navigation and positioning, abnormal observations and kinematic model disturbances are one of the key factors affecting the stability and reliability of positioning performance. Generally, robust adaptive filtering algorithm is used to reduce the influence of them on positioning results. However, it is difficult to accurately identify and separate the influence of abnormal observations and kinematic model disturbances on positioning results, especially in the application of kinematic Precise Point Positioning (PPP). This has always been a key factor limiting the performance of conventional robust adaptive filtering algorithms. To address this problem, this paper proposes a two-step robust adaptive filtering algorithm, which includes two filtering steps: without considering the kinematic model information, the first step of filtering only detects the abnormal observations. Based on the filtering results of the first step, the second step makes further detection on the kinematic model disturbances and conducts adaptive processing. Theoretical analysis and experiment results indicate that the two-step robust adaptive filtering algorithm can further enhance the robustness of the filtering against the influence of abnormal observations and kinematic model disturbances on the positioning results. Ultimately, improvement of the stability and reliability of kinematic PPP is significant.     

横流中空心锥形喷雾的扩散特性与影响因素

为了更好地理解和认识空心锥形喷雾射流与横向气流的掺混过程，基于可视化实验测量，针对空心锥形喷雾的初始雾化状态、喷射角度和雾化锥角以及横流速度等因素对空心锥形喷雾射流在横流中的扩散特性进行了系统分析。研究结果表明，随着横流速度的提高，流场中对称反旋涡对（CVP）结构变小，但其稳定性及产生的卷吸气流则是先增强而后减小；提高喷雾初始液滴的动量和数流率，均可以增大射流剪切层的贯穿深度和射流尾迹的伸展高度，同时使流场中CVP的涡量强度增大。基于实验测量结果，建立了空心锥形喷雾垂直入射横流条件下掺混流场液滴群CVP结构特征尺寸和剪切层轨迹的预测关联式。另外针对喷嘴雾化锥角和喷射角度的分析表明，当喷雾初始雾化状态相近时，随着雾化锥角的减小，流场中CVP的水平尺度减小但竖直方向尺度增大且结构更为稳定，同时喷雾液滴的贯穿深度增大；相比喷雾垂直于横流入射，当喷嘴以一定角度逆向横流入射时，CVP结构稳定性减弱，流场剪切层涡结构变大且剪切层区域液滴富集现象减弱，射流尾迹紊乱程度增加，反之，则流场剪切层涡拟序结构变小，射流尾迹现象减弱，CVP结构变小。     

基于随机维纳过程的航空发动机性能衰退研究

针对发动机下发间隔预测的问题，研究了发动机性能衰退规律。基于发动机排气温度裕度（EGTM）数据，建立了随机维纳模型，并使用严酷度因子修正模型，表征不同的工作条件对发动机的影响。利用期望最大化（EM）算法结合贝叶斯定理，对模型参数求解，最终得到了基于性能衰退的发动机平均下发间隔。研究结果表明，在严酷度因子为1.2696的使用条件下，某型号航空发动机性能衰退平均下发间隔为8219循环；基于该模型预测的发动机平均下发间隔与厂商建议的下发时间之间的误差仅为1.7%。     

Two-stream instability generation in the lunar ionosphere

The Two-stream Instability (TSI) generation is studied analytically in the lunar ionosphere. The TSI is a tiny perturbation in the electron plasma density, due to which an electric field grows with time and this growth is facilitated by the electron plasma in the background. In lunar ionosphere, the TSI comes into existence when the solar wind interacts unhindered with the tenuous lunar electron plasma in the surface bound exosphere. In this study, the conditions which allow the TSI to form and the subsequent instability growth with time i.e. the growth factor, is estimated. Initially, the threshold condition for the TSI to take place is determined. Thereafter, the solar wind and lunar plasma parameter contribution to trigger TSI is investigated along with the effect of these parameters in the evolution of TSI. The plasma TSI evolution with the passage of time is also depicted in phase space diagram with Particle-In-Cell simulations.     

Fault mode probability factor based fault-tolerant control for dissimilar redundant actuation system

This paper presents a Fault Mode Probability Factor (FMPF) based Fault-Tolerant Control (FTC) strategy for multiple faults of Dissimilar Redundant Actuation System (DRAS) composed of Hydraulic Actuator (HA) and Electro-Hydrostatic Actuator (EHA). The long-term service and severe working conditions can result in multiple gradual faults which can ultimately degrade the system performance, resulting in the system model drift into the fault state characterized with parameter uncertainty. The paper proposes to address this problem by using the historical statistics of the multiple gradual faults and the proposed FMPF to amend the system model with parameter uncertainty. To balance the system model precision and computation time, a Moving Window (MW) method is used to determine the applied historical statistics. The FMPF based FTC strategy is developed for the amended system model where the system estimation and Linear Quadratic Regulator (LQR) are updated at the end of system sampling period. The simulations of DRAS system subjected to multiple faults have been performed and the results indicate the effectiveness of the proposed approach.     

改进的离心压气机滑移因子模型

建立一种基于Qiu模型的改进的离心压气机滑移因子模型。该模型在Qiu模型的基础上，增添二次流项来修正滑移因子，同时考虑了出口叶片角与最大叶片角的差值及相应位置。采用亚声速叶轮Krain4、跨声速叶轮Krain6和IET200叶轮对该改进模型进行CFD验证，并对模型二次流项中常系数c的取值进行讨论。结果表明:与Qiu模型及其他传统滑移因子模型相比，该改进模型的精度较高，平均相对误差在2%以下，适用于亚声速及跨声速离心压气机。      

基于波长控制的光纤陀螺标度因数温度性能提高方法

光纤陀螺的标度因数与光纤环的长度、直径及光源的平均波长有关。在温度条件下，光纤环的长度、直径及光源的平均波长均会发生变化，进而导致光纤陀螺在高低温下的标度因数不同，影响温度环境下的光纤陀螺标度因数的重复性。提出了一种基于光纤陀螺波长控制的标度因数温度性能提高方法，该方法在光源驱动电路的桥式回路中增加了铂电阻组件，从而可自动调节光纤陀螺光源的管芯温度，进而控制光源平均波长的变化，以抵消光纤环有效面积因温度变化而对标度因数产生的影响，提高温度环境下光纤陀螺的标度因数重复性。试验表明，该方法将未补偿情况下光纤陀螺全温范围内的标度因数重复性(1σ)由271×10-6~280×10-6减小到了32.5×10-6~43.5×10-6，标度因数重复性误差减小了84%~88%，并验证了该方法的有效性。     

用于叶片减振的压电材料分布拓扑优化

提出一种可用于实际叶盘结构的压电分支阻尼器拓扑优化方法,可以给出总质量受约束的压电材料在叶片上的最佳分布,达到尽可能大的模态阻尼比。通过理论推导说明:压电阻尼器所产生的模态阻尼比仅取决于模态机电耦合系数,且该系数只与压电材料的几何形状以及模态应力场有关。进一步结合压电本构关系,基于应力分量的线性加权给出了有限的压电材料在叶片上铺设位置“优先级”的判断指标。给出了基于叶盘结构有限元模型的压电材料拓扑优化方法,通过替换单元类型和材料参数的方式对压电材料进行布置,并给出了多模态族优化、极化方向设置、电极铺设等问题的解决方案。在一个接近真实的叶盘模型上应用了此优化方法。结果表明,仅使用质量占叶片质量10%的压电材料,就可以为多个模态提供约12%的阻尼比。      

基于改进准则法的复合壳阻尼结构拓扑减振动力学优化

针对复合壳阻尼结构的拓扑减振优化问题，以约束阻尼层的有限单元为设计变量，采用体积比、模态频率和振型为优化约束条件，构建以多模态权重系数的结构模态损耗因子数值关系为优化目标函数的拓扑减振优化模型。为了拓展优化目标灵敏度具有不局限于某一变密度法插值模型的形式，推导了数值表达式的一般函数式。动力学优化中优化目标灵敏度正、负数集共存，使得非凸性的目标函数设计变量出现负值或优化函数寻优于局部极值点。为此，推导出复合壳阻尼结构的全域灵敏度改进优化准则法迭代格，以确保每次迭代域均为全域设计变量集。结合有限单元法编程实现了复合壳阻尼结构改进准则法，并对复合壳结构进行拓扑减振优化分析。结果表明：在敷设体积减为全覆盖的50%时，复合壳结构的模态损耗因子增减偏差为10%，具有提升减振的轻量化设计目的；各阶目标函数和拓扑构型所需的迭代次数少，中间密度区域较小，多阶优于单阶模态优化函数，易于获得全域寻优的有效减振。