高马赫数层流摩阻数值计算精度

飞行器在高空高速飞行时黏性效应显著，摩阻预示精度对飞行器的关键气动性能意义重大。目前，摩阻预示主要依赖数值计算，但高马赫数层流摩擦阻力计算与试验测量结果仍存在差距。以具有高速飞行器典型部件特征的球锥、三角翼为对象，结合风洞试验摩阻测量结果，使用国家数值风洞（NNW）数值计算软件和自研CFD程序研究了数值计算中影响摩阻计算精度的格式数值耗散及壁面温度边界条件等重要因素。研究结果表明：数值耗散越小，表面摩阻的计算精度越高；在速度较低的边界层近壁区内关闭熵修正，将有助于提高表面摩阻的预示精度。此外，在高马赫数流动问题的数值模拟中，壁面温度条件对表面摩阻计算同样具有重要影响。最后，基于分析结果和工程需要提出了对高精度摩阻数值预示的研究需求。     

S弯收扩喷管流动特性数值研究

为了研究S弯收扩喷管的流动机理，数值模拟了不同喷管落压比（NPR）和S形收敛管道出口面积比（A₇₂/A₈）对S弯收扩喷管内流动的影响。结果表明：当S弯收扩喷管处于高度过膨胀状态时，随着NPR升高，非对称分离逐渐转变为对称分离，λ型激波转变为马赫盘结构，气动性能下降，推力矢量角减小；随着NPR继续上升，激波从喷管内移动到喷管出口边缘，并逐渐转变为膨胀波，气动性能上升，推力矢量角减小至0°后保持不变。在完全遮挡高温部件的低可探测准则的约束下，出口面积比A₇₂/A₈的变化主要对S弯收扩喷管收敛段的流动特性产生显著影响，体现在S弯收扩喷管内的局部加速及二次流分布。S弯收扩喷管的气动性能随着A₇₂/A₈增大而提高，但当A₇₂/A₈增大至1.8时，第一弯管道出口上壁面发生流动分离，气动性能显著下降。     

基于惯性定位定向的高铁轨检仪研究

根据高铁轨道静态检测的测量需求，设计了一种利用定位定向技术的0级轨检仪，详细阐述了其构成和工作原理，介绍了其特点。通过对比性分析论证，优选了一种测量精度高、操作方法简单且可大幅度提高测量效率的设计方案。理论仿真表明，本系统测量精度能够达到优于13mm/km水平。根据理论仿真结果搭建了原理简易验证设备，结合高铁测控网的测量基准，在一段高铁的弯道铁轨上进行了验证测试。从测试结果看，样机测量精度的重复性可以到达1mm/500m（1σ）的水平，10次测量效率优于500m/2h，表明采用定位定向技术的0级轨检仪具备实际工程化的潜力，以及提高测量效率和精度的能力。     

双流制窄轨电力机车用异步牵引电机设计

将牵引电机应用于双流制窄轨电力机车时,由于窄轨机车轨距小,所以牵引电机安装空间异常狭小,比一般牵引电机在安装空间、电机结构、电磁负荷等方面的要求更加苛刻。针对窄轨双流制电力机车的运用特点和特殊要求进行了分析,提出了牵引电机的设计要求和关键技术难点,并对关键技术难点给出了相应的分析和解决措施。对该牵引电机的制造过程及电机试验测试情况进行了论述。试验结果表明,该牵引电机达到了设计预期,完全能满足设计要求。     

Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.     

高温存储对Sn-Pb-Ni凸点界面金属间化合物生长的影响

倒装焊工艺由于具有信号处理速度快、封装密度高、可靠性高等特点，已广泛应用于高密度集成电路封装工艺中。高可靠倒装焊器件的互连焊点通常采用10Sn90Pb等高铅焊料，该焊料具有剪切强度高、可靠性高等优点，但其熔点高、回流工艺窗口窄等特性给封装工艺带来一定难度，此外该焊料在高温存储环境的可靠性有待进一步提高。本文采用Ni元素对10Sn90Pb焊料进行改性，研究高温存储下Sn-Pb-Ni体系凸点的力学性能以及金属间化合物（Intermetallic compound,IMC）的生长演变规律，以此评估Ni元素对10Sn90Pb凸点可靠性的影响。主要结果如下：适量添加Ni元素可以细化10Sn90Pb焊点界面处IMC晶粒，降低高温存储条件下的IMC生长速度，但在一定程度上会降低凸点的剪切强度。0.05%~0.1%含量的Ni元素添加对10Sn90Pb凸点综合性能提升较为显著。     

Gd2SiO5纳米粉体的并流化学共沉淀法合成

以Gd₂O₃和正硅酸乙酯(TEOS)为原材料,采用并流化学共沉淀法合成Gd₂SiO₅粉体材料。研究Gd₂SiO₅前驱体的热响应特征、Gd₂SiO₅粉体的物相组成和微观形貌,并对Gd₂SiO₅粉体的合成机理进行初步探讨。结果表明:前驱体的低Gd/Si摩尔比和反应体系的高pH值会导致Gd₂SiO₅粉体生成Gd_9.33(SiO₄)₆O₂杂质相,相反则会导致生成Gd2O3杂质相。当Gd/Si摩尔比为20∶11、pH值为9~10、合成温度为1000~1300℃时,合成的粉体纯度较高,Gd₂SiO₅颗粒呈不规则形貌特征,平均粒度为100~200 nm。Gd₂SiO₅合成过程中,前驱体以一种—[Si—O—Gd]—网络结构存在,在煅烧过程中逐渐转化为Gd₂SiO₅晶体以及Gd_9.33(SiO₄)₆O₂和Gd₂O₃杂相。     

弹载变转速定量泵高动态压力控制特性分析

传统弹载电液伺服系统的液压能源采用有刷直流电机驱动恒压变量泵的方式，泵源压力在导弹飞行过程中设定值恒定，但在平飞段过程长、负载小，对能源压力需求低，造成弹上能源总利用率不高的问题，提出无刷直流电机驱动小排量液压泵的压力控制泵源的设计，在低气动负载阶段适当降低系统压力，进而降低节流损失与泄漏量，提高能量利用率。分析了变转速定量泵的流量压力特性曲线，通过建立基于变转速压力控制泵源的位置电液伺服系统数学模型与仿真模型，分析了变转速定量泵压力控制系统在典型工况下的位置跟踪、系统压力变化与能量利用效率，验证了压力控制系统能够在导弹平飞段保证位置伺服系统跟踪正常的前提下，能有效提高系统效率，证明了变转速定量泵压力控制系统的有效性与可行性。     

Laser-induced oxidation assisted micro milling of high aspect ratio microgroove on WC-Co cemented carbide

Severe tool wear and poor surface quality are the main problems during micro machining of cemented carbide. In this work, an innovative hybrid process of laser-induced oxidation assisted micro milling (LOMM) was proposed to solve the problems. A nanosecond laser was utilized to induce oxidation of the WC-20%Co material, producing loose oxide which was easy to remove. The micro machinability of the material was improved by laser-induced oxidation. The oxidation mechanisms of cemented carbide were studied. A microgroove with a depth of 2.5 mm and aspect ratio of 5 was fabricated successfully. The milling force, surface quality and tool wear mechanisms were investigated. For comparison, a microgroove was also fabricated with conventional micro milling (COMM) using identical milling parameters. Results revealed that in LOMM the milling force and tool wear rate were extremely low during removing the oxide. The machined surface quality and dimensional accuracy achieved by LOMM were superior to those obtained by COMM. The surface roughness S_a of the microgroove bottom reached 88 nm in LOMM, while the cross-sectional geometry of the microgroove was a trapezoid. Perpendicularity of the microgroove sidewall machined by LOMM was better than that by COMM. The tool wear forms in LOMM were coating spalling and slight tool nose breakage. Compared with COMM, the tool life in LOMM was prolonged significantly. It indicates that the proposed hybrid process is an effective and efficient way to fabricate high aspect ratio micro-features with high dimensional accuracy.     

高温铝合金电磁超声检测回波特性及因素分析

针对高温铝合金在线检测条件下，温度对铝合金电磁超声检测回波特性的影响规律尚不明确、高温检测时缺陷定量/定位补偿困难这一难题，以螺旋线圈电磁超声换能器（EMAT）为例，建立了高温铝合金EMAT检测过程的场路耦合有限元模型；研究了温度对EMAT激励/接收换能效率、EMAT激励/接收电路的功率分配特性、超声传播过程中的扩散/介质衰减特性、回波幅值和超声声速等因素的影响规律；研制了耐高温EMAT探头，对20~500℃高温铝合金试样进行了检测实验，并测定了高温铝合金的超声介质衰减系数和超声声速。在仿真和实验相结合的基础上，分析了高温检测时超声回波幅值变化特性及其影响因素。结果表明：对于铝合金这类非铁磁性金属材料，导致高温时超声回波幅值下降的主要原因是超声介质衰减系数随着温度的升高而增大，其次为高温时EMAT激励/接收电路的功率分配特性的改变。在激励EMAT在试样表面形成的洛伦兹力不变的条件下，其所激励的超声波回波幅值具有随着温度的增加而增加的特点，可以有效减缓超声回波幅值下降的趋势。