半球谐振子疲劳寿命分析与仿真

半球谐振子的寿命和损伤是直接影响高精度半球谐振陀螺使用时长和安全性的重要因素。目前国内加工的半球谐振子所用的熔融石英玻璃材料主要依靠进口，采用传统的疲劳寿命实验确定方法成本过于昂贵，因此需要利用疲劳分析软件对半球谐振子的疲劳寿命进行分析。文章通过半球谐振陀螺应力分析，采用ANSYS软件对熔融石英半球谐振子进行应力分析仿真，确定因残余应力所引起的疲劳危险部位，并在疲劳部位进行裂纹扩展分析，得到 、 和 型应力强度因子，以使在半球谐振子结构设计和使用过程中对易疲劳的部位进行有效监控和预防。     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

一种地月转移轨道中途修正的制导算法

针对地月转移轨道中途修正问题，提出了一种求解修正速度增量的制导算法。该算法由初值设计和精确解求解两部分组成。首先，利用伪状态理论，通过简单迭代设计中途修正的初值，并通过Vinti预报方法修正了地球扁率的影响。然后，在求解精确解时，提出了一种基于伪状态理论的状态转移矩阵解析算法。该算法通过设计高精度的初值，降低了求解地月转移轨道中途修正问题的难度，而且避免了传统数值方法计算状态转移矩阵的复杂性。数值仿真结果表明，该算法可有效求解中途修正问题。     

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

离心压缩机密封及空腔流动的一维/三维耦合建模研究

为了在保证数值预测精度的同时降低离心压缩机的建模复杂度,以一维密封泄漏计算替代完整的密封及空腔建模,开展了离心压缩机盖盘密封及空腔流动的源项建模方法研究。结果表明:基于源项方法的密封及空腔简化建模仅需在主流道建模基础上施加泄漏质量流量、总温和摩擦损失源项边界条件,即可较高精度地还原完整的盖盘密封及空腔建模的性能和关键流动细节。与完整建模相比,在全工况下源项建模预测的等熵效率的绝对偏差小于0.65%,总压比和等熵效率的相对性能偏差小于1%。该方法可在满足下游部件匹配设计精度需求的同时,减少50%以上的网格数量,并显著提高计算的经济性和收敛性。泄漏流量的计算精确度是影响源项建模法性能预测准确性的最关键因素,耦合建模可以采用一维计算中推荐的密封泄漏系数值。      

低排放燃烧室NO_x排放试验及预测方法研究

为了研究中心分级贫油低排放燃烧室的排放特性和排放预测方法,针对一个低排放头部方案,在单头部燃烧室试验件上,在不同的温度、压力、油气比、供油模式和分级比条件下,测量其排放性能。以Lefebvre排放经验预测公式为基础,采用经验分析方法拟合排放试验数据,归纳出适用于本头部方案的排放预测公式。表征预测好坏的判定系数R2在小工况下和大工况下分别为0.95和0.93,表明预测结果与试验结果符合度较好。小工况和大工况排放特性不同,对仅预燃级喷油的小工况工作模式,NO_x排放主要受化学恰当燃烧温度和预燃级局部当量比的影响;对预燃级和主燃级同时喷油的大工况工作模式,NO_x排放主要受燃烧区温度和主燃级燃油比例的影响。     

比例与非比例加载下30CrMnSiA钢多轴高周疲劳失效分析

为了分析比例与非比例加载下,30CrMnSiA钢的多轴高周疲劳的失效规律。通过对30CrMnSiA钢材料开展比例与非比例(δ=90°)加载下的多轴高周疲劳试验,研究了应力幅比和相位差对疲劳寿命、断口特征及裂纹起裂角度的影响。试验结果表明,对于比例与非比例加载,随着应力幅比的增大,多轴疲劳寿命逐渐增加。对疲劳断口分析发现,裂纹萌生于试件表面,断口有明显的疲劳源区、扩展区和瞬断区,不同加载路径下的试件断口形式有明显差异。通过对起裂角度的分析发现,应力幅比大于0.25时表面裂纹有明显的第Ⅰ阶段向第Ⅱ阶段的转变,且第Ⅰ阶段沿着接近最大剪应力幅值平面方向扩展,第Ⅱ阶段沿着接近最大正应力平面方向扩展。此外,对典型试件的疲劳断口及表面扩展路径进行了分析,研究表明多轴疲劳试验试件裂纹的特征比值在0.3~0.5之间,且裂纹沿深度方向扩展至300 μm时占总寿命的85%以上。      

基于IPSO-Elman神经网络的飞机客舱能耗预测

为了提高飞机客舱使用地面空调制冷时客舱能耗的预测精度，提出了一种改进的粒子群优化（IPSO）Elman神经网络的飞机客舱能耗预测模型。依据对算法中惯性权重与学习因子的收敛域分析，得出了二者合理的取值范围，将粒子到全局最优位置间距离与参数的取值范围相结合，构造了惯性权重与学习因子的动态调节函数，对其进行非线性的动态调节，并引入了变异因子，提出了一种跳出局部最优的策略，防止粒子群优化（PSO）陷入局部最优。将IPSO-Elman应用于Boeing738飞机客舱能耗预测中，与PSO-Elman、Elman算法进行性能比较，仿真结果表明基于IPSO-Elman的客舱能耗预测模型在预测精度和收敛速度方面均有一定的提升。该研究结果为飞机客舱能耗预测模型的建立提供了理论依据，对飞机地面空调的节能与机场电能合理调配提供了支持。     

基于图像识别的机械振动信号特征提取与寿命预测方法研究

滚动轴承作为许多机械设备的关键组件,被广泛应用于机械制造、航空航天等领域,其健康状态直接影响了相应设备的剩余寿命,因此在设备故障预测与健康管理(Prognostics and Health Management, PHM)领域,滚动轴承寿命预测具有很高的研究价值。目前基于数据驱动的轴承寿命预测方法主要利用特征提取并构造健康因子(Health Indicator, HI),然而在这一过程中特征的选择与融合依然依赖于专家先验知识,并且健康因子也很难从复杂的时序数据中进行提取。因此,提出了一种新型的数据驱动寿命预测算法,在特征提取方面,通过连续小波变换(Continuous Wavelet Transform,CWT)将传感器振动信号转换为时频谱图,再通过深度残差网络(Deep residual network, ResNet)结合时空卷积网络(Temporal Convolutional Network, TCN)将时频谱图中的时域频域特征构造成为健康因子,最后完成剩余寿命预测。本研究在PRONOSTIA数据集上与现有的数据驱动算法进行了对比,证明了该算法可以更准确地完成剩余寿命预测。     

基于TLE的弹道系数计算方法及应用分析

针对仅使用两行要素（Two Line Element，TLE）作为数据源的应用需求，研究了基于TLE轨道衰减的弹道系数计算方法。介绍了一种常用的基于两组TLE的直接计算法，分析TLE选取间隔对结果精度的影响；提出了一种基于多组TLE的迭代计算方法，以降低异常TLE对计算结果的影响；从弹道系数计算效果、在再入预报中的应用等方面对这两种方法进行比较分析。结果表明，两种方法各有优劣，基于多组TLE的迭代计算法稳定性更高、受TLE精度的影响更小；由于数据区间更短，基于两组TLE的计算结果对短期轨道衰减特性反应得更准确，用于临近再入时的预报效果更好。