A multi-stage regulation strategy of space manipulators with a free-swinging joint failure

To ensure tasks can be completed after a free-swinging joint failure occurs, a multi-stage regulation strategy of space manipulators is proposed. Considering all terms of the dynamics equation, an evaluation model of the regulation ability (EMRA) of active joints over the fault joint is established based on the fuzzy entropy. And then a multi-stage regulation strategy based on the EMRA is designed to regulate the fault joint. The strategy divides the regulation process into several stages, and select a certain active joint to regulative the fault joint in every stage. With this multi-stage regulation strategy, the fault joint can be regulated to the desired angle without huge torque on regulative joints. The simulation is carried out with a 7-DOF space manipulator, verifying the correctness and effectiveness of the multi-stage regulation strategy. The strategy has three advantages: Coriolis and centrifugal terms are both considered for the first time in selecting the regulative joint, making the selection result more in line with the actual regulation process; The influence of the model uncertainty is eliminated in establishing the EMRA, making the evaluation of regulative ability more precise; The fault joint is successfully regulated to the desired angle without huge torque on regulative joints.     

基于有向图模型的民机航空电子系统故障诊断

结合民机航电系统外场可更换单元或模块（LRU/LRM）的故障模式及影响分析（FMEA）、故障树 分析和实时性要求，设计了基于时间故障传播图（TFPG）的系统故障诊断元模型和领域模型，研究了基于逻 辑和时间一致性检验的故障诊断算法，使用后向推理和可信度度量列出候选故障集。以飞行管理系统为例，构 造了其功能失效的TFPG 模型，并通过仿真验证了基于TFPG 的诊断在滤除级联效应和关联驾驶舱效应中的有 效性。     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

基于HHT的航空直流串行电弧特征提取方法

由于飞机内部布线空间有限、电弧故障存在发生时间地点随机以及特征不明显等问题，导致检测困难。本文基于航空270 V高压直流（HVDC）系统开展直流串行电弧故障特征提取方法研究，采用希尔伯特黄变换（HHT）提取电弧电流交流分量的时域和频域特征量。选择HHT的固有模态函数IMF5瞬时幅值的峰峰值和标准差作为识别电弧故障的时域特征，与原始信号中提取的时域特征量对比，正常和电弧特征量的区分度更大；选择HHT的固有模态函数IMF1+IMF2、一定频带范围内的瞬时幅值计算得到的谐波功率和作为区分正常和电弧情况的频域特征量。与常用的快速傅里叶变换（FFT）方法相比，HHT三维时频谱能够反映信号的局部特征，HHT方法计算得到的正常和电弧特征量之间的区分度更大，电弧和正常特征量的比值最高可达346。基于HHT的电弧故障特征提取方法能够更好地区分正常和电弧情况，有助于提高电弧故障的检测率，降低虚警率，具有重要的工程应用价值。     

基于自适应Kriging代理模型的交叉熵重要抽样法

对于复杂失效域和小失效概率耦合的可靠性分析问题，本文提出了一种交叉熵重要抽样（CE-IS）方法结合自适应Kriging （AK）代理模型的求解方法（CE-IS-AK）。所提方法基于交叉熵原理，用混合高斯模型逐步逼近最优重要抽样密度函数，并采用AK模型协助逼近过程中混合高斯模型的参数的更新，从而提高了CE-IS方法的计算效率。另外，本文还改进了CE-IS方法的收敛准则，避免了方法的冗余迭代，扩大了方法的适用范围。由于在CE-IS方法中引入了AK模型，因此，本文方法所构建的重要抽样函数在保证精度的基础上提高了效率。相较于AK-MCS方法，本文方法中引入了重要抽样的思想，因此在Kriging训练点数目基本相同的情况下，大幅缩减小失效概率计算时样本池规模，并且由于利用了混合高斯模型，因而对多失效域具有较好的适用性。算例分析也证明了本文所提方法的优越性。     

期望状态序列导向的深空探测器规划修复方法

Aiming at the challenges caused by the persistence, concurrency and energy consumption of probe actions, a plan repair method of deep space probe based on the expected state sequence is proposed. In this method, the expected state sequence is formed of the expected effect of the unfinished action and the expected precondition of the unexecuted action in the pre designed plan, according to the execution status of the action. The expected state sequence is an ordered set of states with mixed logic and energy, providing subgoals for plan repair and also transforming the plan repair problem into the state transition path searching problem. During the search, the plan repair strategy with energy supply priority is proposed, which separates the logic repair from energy repair to reduce the difficulty of solving the problem. And this method enables the probe to recover from plan failure autonomously. Finally, the effectiveness and rationality of the proposed method are verified through simulation by taking the Mars Orbiter as an example.     

叠层穿刺CF/Al复合材料准静态拉伸力学行为与失效机制

针对新型的叠层穿刺碳纤维织物增强铝基复合材料（CF/Al复合材料），通过细观力学数值模拟与实验结合的方法研究了其在准静态拉伸载荷作用下的渐进损伤与断裂力学行为。复合材料经向拉伸弹性模量、极限强度与断裂应变的实验结果分别为129.61 GPa、630.14 MPa和0.75%，细观力学模型预测误差分别为-9.41%、7.57%和1.33%，均匀化计算的宏观应力-应变曲线与实验曲线总体上相符。经向拉伸变形初期首先出现经/纬纱交织处基体合金的局部损伤，随着拉伸应变量的增大依次发生纬纱和穿刺纱的横向开裂，拉伸变形后期基体合金与经纱失效引起宏观应力-应变曲线的急剧下降，复合材料拉伸断口表现为经纱轴向断裂及纬纱和穿刺纱横向开裂共存的形貌特征，纤维拔出和基体断裂导致的经纱轴向断裂是诱发复合材料最终失效的主要机制。     

Adaptive fuzzy terminal sliding mode control for the free-floating space manipulator with free-swinging joint failure

Space manipulator with free-swinging joint failure simultaneously contains kinematic and dynamic coupling relationships, so it belongs to a new underactuated system. To allow the manipulator to carry on tasks, an effective robust underactuated control method for the space manipulator with free-swinging joint failure is studied in this paper. Considering the effect of model uncertainty and joint torque disturbance, a robust underactuated control system based on the Terminal Sliding Mode Controller (TSMC) is designed, but two drawbacks are discussed: (A) Robustness depraves with eliminating chattering. (B) Control parameters are difficult to be determined under unknown uncertainty and disturbance. To improve the TSMC, the adaptive fuzzy controller is introduced to estimate the real effect of unknown uncertainty and disturbance according to deviations of sliding mode and its reaching law. The estimated result is directly compensated into active joints torque. In simulation, the space manipulator with free-swinging joint executes tasks based on the TSMC and the Adaptive Fuzzy Terminal Sliding Mode Controller (AFTSMC) respectively. Same tasks can be finished with smaller joints torque and stronger robustness based on the AFTSMC. Therefore, AFTSMC can serve as an effective robust control method for the space manipulator with free-swinging joint failure under unknown model uncertainty and torque disturbance.     

Implementation of tactical maneuvers with maneuver libraries

This study creates and combines the general maneuver libraries for fixed-wing aircraft to implement tactical maneuvers. First, the generalized maneuver libraries are established by analyzing the characteristics of tactical maneuvers required in battlefields. The 7th order polynomial is applied to both the creation of the maneuver libraries and the generation of the trajectories or flight paths for modal inputs. To track the desired trajectory, we design the Attitude Command Attitude Hold (ACAH) system and the Rate Command Rate Hold (RCRH) system using Model Following Controller (MFC). Moreover, the Line-of-Sight (LOS) guidance law is designed. In particular, the CONDUIT® is employed to optimize the gains so that the control systems meet the aircraft Handling Qualities (HQ) criteria. Finally, flight simulations are performed for the longitudinal loop, immelmann-turn, and climb-slalom-descent maneuvers to verify that tactical aggressive maneuvers are realizable via the combination of maneuver libraries. This study can contribute to the development of flight techniques for aircraft tactical maneuvers and to the revision of air force operational manuals.