半球谐振子疲劳寿命分析与仿真

半球谐振子的寿命和损伤是直接影响高精度半球谐振陀螺使用时长和安全性的重要因素。目前国内加工的半球谐振子所用的熔融石英玻璃材料主要依靠进口，采用传统的疲劳寿命实验确定方法成本过于昂贵，因此需要利用疲劳分析软件对半球谐振子的疲劳寿命进行分析。文章通过半球谐振陀螺应力分析，采用ANSYS软件对熔融石英半球谐振子进行应力分析仿真，确定因残余应力所引起的疲劳危险部位，并在疲劳部位进行裂纹扩展分析，得到 、 和 型应力强度因子，以使在半球谐振子结构设计和使用过程中对易疲劳的部位进行有效监控和预防。     

基于DOA聚类算法的ARM抗有源诱偏技术研究

有源诱偏技术是雷达对抗反辐射导弹的一种重要手段,可以大大降低反辐射导弹的作战效能。为提高对敌目标的精确打击能力,在分析闪烁诱饵诱偏原理的基础上,针对有源诱偏干扰下被动雷达测角精度与稳定度不高的问题,通过对有源诱偏信号的时域特征进行分析,提出一种基于脉冲前沿检测的DOA聚类分选算法,找出前沿超前的辐射源信号,实现了高性能抗有源诱偏干扰和高精度抗干扰测向。仿真结果表明,该技术可以有效对抗四点源有源诱偏干扰。     

Validation of non-linear split window algorithm for land surface temperature estimation using Sentinel-3 satellite imagery: Case study; Tehran Province,Iran

In recent years, land surface temperature (LST) has become critical in environmental studies and earth science. Remote sensing technology enables spatiotemporal monitoring of this parameter on large scales. This parameter can be estimated by satellite images with at least one thermal band. Sentinel-3 SLSTR data provide LST products with a spatial resolution of 1 km. In this research, direct and indirect validation procedures were employed to evaluate the Sentinel-3 SLSTR LST products over the study area in different seasons from 2018 to 2019. The validation method was based on the absolute (direct) evaluation of this product with field data and comparison (indirect) evaluation with the MODIS LST product and the estimated LST using the non-linear split-window (NSW) algorithm. Also, two emissivity estimation methods, (1) NDVI thresholding method (NDVI-THM) and (2) classification-based emissivity method (CBEM), were used to estimate the LST using the NSW method according to the two thermal bands of Sentinel-3 images. Then, the accuracy of these methods in estimating LST was evaluated using field data and temporal changes of vegetation, which the NDVI-THM method generated better results. For indirect evaluation between the Sentinel-3 LST product, MODIS LST product, and LST estimated using NSW, four filters based on spatial and temporal separates between pairs of pixels and pixel quality were used to ensure the accuracy and consistency of the compared pairs of a pixel. In general, the accuracy results of the LST products of MODIS and Sentinel-3, and LST estimated using NSW showed a similar trend for LST changes during the seasons. With respect to the two absolute and comparative validations for the Sentinel-3 LST products, summer with the highest values of bias (?1.24 K), standard deviation (StDv = 2.66 K), and RMSE (2.43 K), and winter with the lowest ones (bias of 0.14 K, StDv of 1.13 K, and RMSE of 1.12 K) provided the worst and best results for the seasons in the period of 2018–2019, respectively. According to both absolute and comparative evaluation results, the Sentinel-3 SLSTR LST products provided reliable results for all seasons on a large temporal and spatial scale over our studied area.     

A novel framework for liquid propellant engine’s cooling system design by sensitivity analysis based on RSM and multi-objective optimization using PSO

One of the challenges of combustion chamber and nozzle design in a Liquid Propellant Engine (LPE) is to predict the behavior and performance of the cooling system. Therefore, while designing, the optimization of the cooling system is always of great importance. This paper presents the multi-objective optimization of the LPE’s cooling system. To this end, a novel framework has been developed, resulting from the application of the Response Surface Method (RSM) and the correlation coefficients matrix, sensitivity analysis and the The Particle Swarm Optimization (PSO). based on this method, the input variables, constraints, objective functions, and their surfaces were identified. In terms of multi-optimization algorithms, RSM and PSO are utilized to get global optimum. In conclusion, the methodology capability is to optimize the LPE’s cooling system, 6 percentage increase in total heat transfer and 7 bar decrease cooling system pressure loss, which resulted in a 1.2-seconds increase in the specific impulse of the engine.     

高背压等离子点火器及其液体燃料点火特性实验研究

航天应用的液体火箭发动机及燃烧型加热器燃烧室室压高、燃料流量大、温度低、有重复启动需求，实现安全可靠点火的难度较大。针对这些需求，研究了一种采用高背压设计的电弧等离子体点火器。实验研究了Ar，N₂气体工质在高进气压力下的伏安特性，发现N₂在宽压力范围内适用于点火。发射光谱分析表明，在高达数MPa的进气压力下，Ar，N₂等离子体射流电子密度符合局部热力学平衡判据（LTE判据），点火能量集中。N₂等离子体整体温度低于Ar，但阳极喷口附近温度高于Ar，N₂等离子体射流火焰长，卷吸沿程空气造成射流平均温度偏低，但有助于低温液体推进剂的蒸发混合和强化点火。等离子体射流引起了臭氧和氮氧化物的形成，具有促进点火和化学反应的作用。背压提高引起电源输出电压升高，提高供气压力和电流，有助于点火器在高背压环境中稳定电压。燃烧型空气加热器燃烧室的点火实验发现，采用N₂等离子体喷注面中心点火，可以在短时间内完成酒精-空气和酒精-液氧-空气的点火，最高燃烧室室压接近5MPa时，点火器仍能稳定工作，多次使用电极烧蚀不明显，在液体火箭发动机的重复可靠点火方面具有很好的应用前景。     

详细化学反应机理对预混丙烷钝体熄火模拟影响

航空发动机熄火预测是重要关键问题之一，湍流和化学反应的非线性相互作用使预测非常困难。本文采用大涡模拟（LES）对湍流进行高精度模拟，采用概率密度函数输运方程湍流燃烧模型（TPDF）耦合JL4、Z66和H73三种化学反应机理，对预混丙烷钝体熄火现象和规律进行研究。JL4的反应机理最简单，反应释热快，局部放热高，火焰宽度大，火焰两侧温度梯度大，燃烧更加趋于稳定，无法模拟出熄火状态。H73机理绝热火焰温度低，火焰温度低，回流区中部OH含量高；在近熄火状态，大量CO被氧化，释放热量过高导致无法模拟出熄火现象。Z66机理可以模拟出火焰正常状态，在低当量比下也可以模拟出熄火状态。本文算例中，局部Da数大于1的区域超过35%则会发生熄火。     

Study of ionospheric D region changes during solar flares using MF radar measurements

During solar flares, the X-ray radiation suddenly increases, resulting in an increase in the electron density of the atmospheric D region and a strong absorption of short-wave radio waves. Based on Langfang medium frequency (MF) radar, this paper analyzed the variation characteristics of D region in the lower ionosphere from 62 km to 82 km. The analysis focused on multiple C-level and M-level solar flare events before and after the large-scale flare event at 11:53 (UT) on September 6, 2017. The results show that it is difficult to detect the electron density over 70 km in Langfang during solar flares, but the electron density value can be obtained as low as 62 km, and the stronger the flare intensity, the lower the detectable electron density height. Besides, the equal electron density height, the received power of X and O waves will also be significantly reduced during the flares, and the reduction of equal electron density height has a weak linear relationship with flare intensity.     

Thermosphere densities derived from Swarm GPS observations

After the detection of many anomalies in the Swarm accelerometer data, an alternative method has been developed to determine thermospheric densities for the three-satellite mission. Using a precise orbit determination approach, non-gravitational and aerodynamic-only accelerations are estimated from the high-quality Swarm GPS data. The GPS-derived non-gravitational accelerations serve as a baseline for the correction of the Swarm-C along-track accelerometer data. The aerodynamic accelerations are converted directly into thermospheric densities for all Swarm satellites, albeit at a much lower temporal resolution than the accelerometers would have been able to deliver. The resulting density and acceleration data sets are part of the European Space Agency Level 2 Swarm products.To improve the Swarm densities, two modifications have recently been added to our original processing scheme. They consist of a more refined handling of radiation pressure accelerations and the use of a high-fidelity satellite geometry and improved aerodynamic model. These modifications lead to a better agreement between estimated Swarm densities and NRLMSISE-00 model densities. The GPS-derived Swarm densities show variations due to solar and geomagnetic activity, as well as seasonal, latitudinal and diurnal variations. For low solar activity, however, the aerodynamic signal experienced by the Swarm satellites is very small, and therefore it is more difficult to accurately resolve latitudinal density variability using GPS data, especially for the higher-flying Swarm-B satellite. Therefore, mean orbit densities are also included in the Swarm density product.     

不同强度磁暴期间热层大气密度响应特征分析

利用CHAMP卫星数据，对2002-2008年12个不同强度磁暴事件期间的热层大气密度变化特征进行分析，并研究对应磁暴期间大气模式NRLMSISE-00分布特征.结果表明，大磁暴期间日侧大气密度峰值从高纬到低纬的时间延迟为2h，中小磁暴期间的延迟时间为3～4h；春秋季暴时大气密度分布基本呈南北对称分布，而夏冬季大气密度的分布是夏半球大于冬半球，春秋季暴时大气密度大于夏冬季；NRLMSISE-00大气模式得到的热层大气密度很好的体现了半球分布以及季节分布的特征，但模式模拟结果偏小；Dst指数峰值比ap指数峰值更能反应大气密度的变化情况.      

模块化永磁直线游标电机等效磁网络及漏磁分析

在模块化永磁直线游标电机的初始设计及优化设计中,使用有限元方法(FEM)计算漏磁系数时需要耗费大量的建模和计算时间。针对这一问题,建立该种电机的等效磁网络模型,在建模期间,考虑气隙中的边缘效应,并计算永磁体组与定子齿在不同相对位置时的等效磁导,得到该种电机在一个周期内不同相对位置时的漏磁磁导和漏磁系数的数学解析表达式。采用FEM验证了该数学解析表达式的准确性。研究结果为模块化永磁直线游标电机的设计提供了理论依据。