石英玻璃的等离子体抛光技术研究现状

具有耐腐蚀、热膨胀系数低等诸多优良物理化学特性的石英玻璃在高性能光学系统中被广泛使用。要求元件达到纳米级别的表面粗糙度，而且没有损伤层和残余应力，因此精加工之后的超精密抛光工序尤为重要。本文介绍了气囊、磁流变、弹性发射、离子束等几种石英玻璃的精密抛光方法，侧重阐述了国内外等离子体的抛光技术，包括等离子体辅助化学刻蚀、等离子体喷射加工、等离子化学蒸发加工研究进展及取得的成果；且对等离子体的未来发展进行概述。     

动力涡轮转子结构系统力学特性稳健设计方法

航空涡轴/涡桨发动机动力涡轮转子是典型多支点支承、具有连接界面、质量/刚度分布不均匀的高速柔性转子系统，其连接结构力学特性和支承刚度的分散性可导致转子系统动力特性恶化。针对典型动力涡轮转子结构系统，指出不可恢复滑移、疲劳、摩擦等连接界面接触损伤是连接结构力学特性产生分散性的内在原因，提出了接触状态系数、接触应力、不可恢复变形能和接触摩擦功等工程适用的定量评估参数。通过对多支点柔性转子-支承系统临界转速分布及其对各支点支承刚度敏感度的影响规律分析，提出了基于支承刚度低敏感区择优的动力特性稳健设计方法，所提方法提高了转子结构系统的稳健性。      

Inertial parameter estimation and control of non-cooperative target with unilateral contact constraint

In this paper, the relative sliding motion between the target and the manipulator’s end-effector is considered and characterized as a unilateral contact constraint. A new possible solution is presented to estimate the inertial parameters of a non-cooperative target while the relative sliding motion exists. First, the detailed analysis of the dynamical model is presented, and a parameter-explicit linear time-varying model is obtained. Then, an extended state observer is constructed based on the new model, which can effectively estimate the unknown inertial parameters of the target when relative sliding motion exists. As the modified reactionless controller requires the knowledge of inertial parameters, a hybrid post-capture control scheme is also established based on the switch law between different controllers. The correctness and efficiency of the proposed algorithm are validated by numerical simulation, which proves a potential framework for the non-cooperative target post-capture operation.     

Energy principle and material removal sequence optimization method in machining of aircraft monolithic parts

In the machining process of aircraft monolithic parts, the initial residual stress redistribution and structural stiffness evolution often lead to unexpected distortions. On the other hand, the stress redistribution and stiffness reduction during the machining process depend on the material removal sequence. The essence of the stress redistribution is releasing the initial elastic strain energy. In the present study, the influence of the material removal sequence on the energy release is studied. Moreover, a novel optimization method is proposed for the material removal sequence. In order to evaluate the performance of the proposed method, the mechanism of the machining distortion is firstly analyzed based on the energy principle. Then a calculative model for the machining distortion of long beam parts is established accordingly. Moreover, an energy parameter related to the bending distortion and the procedure of the material removal sequence optimization is defined. Finally, the bending distortion analysis and material removal sequence optimization are performed on a long beam with a Z-shaped cross-section. Furthermore, simulation and experiments are carried out. The obtained results indicate that the optimized sequence results in a low distortion fluctuation and decreases the bending distortion.     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

超高强高韧马氏体时效钢热变形及航天应用研究

对于航天用超高强高韧C300马氏体时效钢来说,热加工过程中获得等轴细小的再结晶晶粒是实现该钢强韧性最佳匹配的关键环节。采用Gleeble-3800热模拟试验机在温度为850～1 150℃、应变速率为0.01～10 s~(-1)的条件下,对超高强高韧C300马氏体时效钢进行高温轴向压缩变形试验,获得了高温流变曲线,并观察变形后的金相组织。结果表明:C300马氏体时效钢的流变应力和峰值应变随着变形温度的升高和应变速率的降低而减小;试验钢在真应变为0.92、应变速率为0.01～10 s~(-1)的条件下,随着变形速率的提高,其发生完全动态再结晶的温度也逐渐升高,最佳热变形温度区间为1 050～1 150℃;测得试验钢的热变形激活能Q值为391.2 kJ/mol,建立了其热变形本构方程。结果能为C300马氏体钢的数值模拟和热加工工艺的制定提供理论基础。     

电动汽车牵引用水冷异步电机耦合场分析

基于Ansys多物理场仿真分析平台,对1台车用异步电机进行多物理场耦合分析。仿真电机连续运行在额定工况和峰值工况下的温升和热应力,对电机各部分温度场分布进行深入分析,预测电机峰值工况的最长允许时间。通过热-结构的有限元仿真分析电机内部结构的热应力分布,深入分析转子导条端部与端环焊接位置和机壳与铁心过盈配合面的热应力,校核转子导条端部是否存在开焊的风险,并通过热仿真和应力分析计算机壳与铁心在最高温升工况下不发生滑移或涨开的过盈配合量取值。     

超静超稳卫星碰振动力学建模

针对分离式卫星载荷模块(PM)受到扰动时可能与服务模块(SM)发生碰撞的问题，综合音圈电机反电动势(back-EMF)和柔性线缆动力学的效应，基于牛顿欧拉法建立了分离式卫星(DFP)载荷模块动力学模型。基于Hertz接触理论，推导了分离式卫星碰撞过程中连续接触力模型，并分析了碰撞过程中产生的接触力对载荷模块指向精度和指向稳定度的影响。数值仿真结果表明，碰撞使得载荷模块指向精度和指向稳定度下降5个数量级，碰撞后载荷模块可再次恢复到超静超稳工作状态，恢复时间超过1400 s。本文建立的碰撞模型对研究分离式卫星碰撞规避和碰撞控制具有重要意义。     

复合材料层合板单搭接机械连接横向力研究

在复合材料单搭接连接结构中,由于载荷的偏心作用,在搭接处产生沿板厚度方向的横向力,使得接头产生横向位移并使螺栓偏转。采用试验及有限元方法对复合材料双钉单搭接机械连接中螺栓、螺母在静载荷作用下的应力进行研究,并进行结果分析。结果表明:单搭接中偏心矩在螺栓上的螺纹位置产生较大的应力,使螺栓发生断裂破坏;在螺母中产生较大的弯曲应力,使螺母发生破坏;在连接区两端对层合板施加横向约束能够有效降低螺栓、螺母中的应力幅值;计算结果与试验破坏模式吻合。     

柔性接头结构应力经验公式适用性

设计了接头球半径为8cm的柔性接头及其增强件环向应力电测系统，测试了不同燃烧室压强和摆角条件下增强件的环向应力，并与现有经验公式、有限元分析结果进行了对比，基于有限元分析研究了接头球半径变化对增强件环向压缩应力的影响，提出了新的接头球半径在6~10cm范围内增强件环向压缩应力估算公式，另外研究了喷管喉径对柔性接头结构应力的影响，讨论了冷试容器压强和热试车发动机燃烧室压强换算公式的适用性。结果表明:增强件环向压缩应力试验测试结果和有限元计算结果吻合较好，现有增强件环向压缩应力经验公式估算结果值得商榷，柔性接头冷试结构应力与热试结构应力是不同的，冷试容器压强和热试车发动机燃烧室压强换算公式对于增强件环向压缩应力是适用的，但是对弹性件切应力不适用。