首页 | 本学科首页   官方微博 | 高级检索  
文章检索
  按 检索   检索词:      
出版年份:   被引次数:   他引次数: 提示:输入*表示无穷大
  收费全文   165篇
  免费   88篇
  国内免费   48篇
航空   242篇
航天技术   9篇
综合类   10篇
航天   40篇
  2022年   20篇
  2021年   21篇
  2020年   21篇
  2019年   14篇
  2018年   15篇
  2017年   20篇
  2016年   18篇
  2015年   10篇
  2014年   15篇
  2013年   12篇
  2012年   18篇
  2011年   21篇
  2010年   10篇
  2009年   13篇
  2008年   11篇
  2007年   10篇
  2006年   3篇
  2005年   8篇
  2004年   4篇
  2003年   9篇
  2002年   5篇
  2001年   3篇
  2000年   6篇
  1999年   4篇
  1998年   1篇
  1997年   2篇
  1995年   3篇
  1993年   1篇
  1992年   1篇
  1989年   2篇
排序方式: 共有301条查询结果,搜索用时 15 毫秒
1.
减压腔宽度对刷式密封泄漏特性和滞后效应的影响   总被引:1,自引:0,他引:1  
对减压腔轴向宽度分别为0、04 mm和06 mm的基本型和两种低滞后刷式密封结构进行了静态和动态下压差升降和转子转速升降循环试验,并对其泄漏特性和滞后效应进行了研究。研究结果表明:压差大于02 MPa后,同一压差下的动态泄漏系数比静态降低约14%~20%;低滞后结构的密封性能优于基本型,其泄漏系数最高比基本型降低约20%;静态压差升降循环中,减压腔轴向宽度为06 mm的低滞后结构的滞后效应最强;动态的压差升降循环中,基本型结构的滞后效应最强。转子转速升降循环前后,w为06 mm结构泄漏系数减小约15%,滞后效应最强,减压腔轴向宽度为04 mm结构几乎不存在滞后效应;三种结构中,减压腔轴向宽度为04 mm的结构密封性能最优,滞后效应也最弱。  相似文献   
2.
膜盒式端面密封在低温液体火箭发动机涡轮泵中有着广泛的应用,作为直接影响密封工作稳定性及涡轮泵工作可靠性的重要参数,端面比压、膜盒平衡直径等如何选取一直是密封设计的重要工作。以某型低温液体火箭发动机涡轮泵的膜盒式端面密封为研究对象,研究压缩量、工作压力对膜盒应力分布、平衡直径、载荷系数和端面比压的影响。应用有限元法建立了膜盒应力分析模型,得到了不同压缩量和充压压力下膜盒的应力分布和端面压紧力,分析膜盒平衡直径随压力增大而显著下降的机理。结合理论分析,开展比压测量装置设计和测量,验证数值仿真得出的规律,并发现现有产品的实际平衡直径比理论计算要小。最后基于仿真和测试结果对现有端面密封方案进行改进,通过台架运转试验验证仿真、测量以及改进方案的准确性,为低温液体火箭发动机涡轮泵用密封端面比压的选取提供了更为合理可行的方法。  相似文献   
3.
《中国航空学报》2020,33(3):893-901
In this paper, the effect of different amount of protrusion on various parameters in rotor–stator system was experimentally studied by measuring CO2 concentration and pressure, in order to obtain the optimal protrusion amount. The parameters of different dimensionless sealing flow were measured under the condition that the annulus Reynolds number was 4.39 × 105 and the rotating Reynolds number was 1.05 × 106. The results show that the change of the amount of protrusions has little effect on the static pressure in the cavity, and the static pressure change near the sealing ring is almost negligible. But the total pressure and sealing efficiency increase first and then decrease with the increase of the amount of protrusion. The variation of power consumption is the same. A complex vortex structure will appear at the high radius region when the protrusion is installed. On the other hand, the protrusion can effectively reduce the minimum sealing flow of the rotor–stator cavity. Furthermore, considering the sealing efficiency and power consumption, the best range of the protrusion amount is about 36. The ratio near this range can optimally balance the alleviation of the gas ingestion and the reduction of the power consumption.  相似文献   
4.
《中国航空学报》2020,33(8):2162-2175
The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.  相似文献   
5.
A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal's dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.  相似文献   
6.
《中国航空学报》2020,33(4):1192-1205
Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.  相似文献   
7.
离心压缩机密封及空腔流动的一维/三维耦合建模研究   总被引:1,自引:0,他引:1  
为了在保证数值预测精度的同时降低离心压缩机的建模复杂度,以一维密封泄漏计算替代完整的密封及空腔建模,开展了离心压缩机盖盘密封及空腔流动的源项建模方法研究。结果表明:基于源项方法的密封及空腔简化建模仅需在主流道建模基础上施加泄漏质量流量、总温和摩擦损失源项边界条件,即可较高精度地还原完整的盖盘密封及空腔建模的性能和关键流动细节。与完整建模相比,在全工况下源项建模预测的等熵效率的绝对偏差小于0.65%,总压比和等熵效率的相对性能偏差小于1%。该方法可在满足下游部件匹配设计精度需求的同时,减少50%以上的网格数量,并显著提高计算的经济性和收敛性。泄漏流量的计算精确度是影响源项建模法性能预测准确性的最关键因素,耦合建模可以采用一维计算中推荐的密封泄漏系数值。   相似文献   
8.
为揭示流阻元件的流动损失机理,本文从热力学理论出发,建立了流阻元件的质量流量模型和熵产模型,分析了质量流量与熵产之间的关系,研究了熵产随系统压比和进口总压的变化情况,并通过预旋喷嘴和篦齿封严的实验结果对两个模型进行了分析评估。结果表明,质量流量模型与实验结果的最大偏差不超过2.8%;熵产模型与实验结果的最大偏差不超过1.9%。系统熵产随系统压比的增加而增大,随进口总压的增加而减小。当系统的进口总压,进口总温和出口静压不变时,模型中的参数a是衡量不同元件熵产大小的唯一量度。  相似文献   
9.
黄镜玮  付维亮  马国骏  王国杰  高杰 《航空学报》2021,42(7):124549-124549
为探究动叶上游不同轮缘密封结构封严出流对1.5级涡轮端区流场及轮缘密封间流动干扰的影响区别,通过Shear Stress Transport (SST)湍流模型对无密封腔室,上游密封结构分别为简单斜向、简单径向,下游密封腔室为简单轴向的1.5级涡轮进行了非定常数值模拟。结果表明:轮缘密封间干扰使带径向密封结构模型的下游轮缘腔室内封严效率偏低,并增强了固有的非定常不稳定特性。上游密封结构变化对动叶和第2级静叶流动的影响差异分别位于35%、65%叶高范围内;径向密封结构增加了上游静叶的堵塞效应、动叶入口气流的欠偏转程度、叶根吸力面负荷与14%叶高以上的轮毂通道涡强度,并在第2级静叶入口处产生更多低频压力波动,使其尾缘脱落涡尺度增大但13%叶高以上的轮毂通道涡强度较弱。与无密封腔室相比,通入封严气体总量为主流流量的0.8%时,带斜向密封结构的1.5级涡轮气动效率降低了0.94%,且带径向密封结构的1.5级涡轮气动损失额外增加了0.17%。  相似文献   
10.
为了获取篦齿封严鼓筒齿腔内的压力分布,掌握鼓筒气动特性情况,建立了带封严篦齿鼓筒的三维流场通道模型,计算转静子同心和不同偏心量条件下鼓筒表面静压,分析气动载荷作用下鼓筒的力学特性.仿真结果表明:偏心量的变化使表面静压出现复杂变化,周向静压幅值变动明显,最大偏心量下的静压幅值比无偏心时增长3倍;偏心引起的周向静压波动使鼓筒应力幅值最大浮动3%左右.  相似文献   
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号