面向建筑空间的OFDM信号定位性能分析

针对利用OFDM信号进行定位时信号非连续性问题,提出一种粗检测和精细检测结合的测距方法,将距离测量转换为不同尺度的时延样点,采用时域粗检测快速估算接收OFDM信号的最大相关峰值,然后对传输时延进行频域精细测量,提升了小数倍采样周期时延测量的精度。在此基础上,分析了OFDM信号的定位性能,仿真结果表明,当OFDM信号在信噪比-11dB的情况下测距误差由3m左右(子载波数512)降至1m(子载波数4096)。     

RTK model and positioning performance analysis using Galileo four-frequency observations

This paper proposes a real-time kinematic (RTK) model that uses one common reference satellite for the Galileo system with four frequency observations. In the proposed model, the double-differenced (DD) pseudorange and carrier phase biases among the different frequencies are estimated as unknown parameters to recover the integer features of the DD ambiguities among the different frequencies for ambiguity resolution and precise positioning. Analysis results show that the E5a, E5b, and E5 frequencies have virtually the same performance in terms of the positioning accuracy, observation residuals, and ratio values of ambiguity resolution. However, the E1 frequency performs worse than the E5a, E5b, and E5 frequencies. The RTK results for the combination of multiple frequencies are much better than those for a single-frequency observation, the coordinates’ standard deviation is improved about 20–30%, and the ambiguity fix time is improved about 10%.     

Estimating inter-system biases for tightly combined Galileo/BDS/GPS RTK

The overlapping carrier frequencies L1/E1, L5/E5a and B2/E5b from GPS/Galileo/BDS allow inter-system double-differencing of observations, which shows a clear advantage over differencing of the observations of each constellation independently. However, the inter-system biases destroy the integer nature of the inter-system double-differencing ambiguities. Two methods of direct rounding and parameter estimation are used to determine the ISB value. By analyzing data collected from Curtin University from 2015 to 2018, the phase and code inter-system bias (ISB) are related to the receiver type, firmware version and the selected overlapping frequency. Upgrade of receiver firmware version results in changes of ISB values. For example, the upgrade of Javad firmware in Dec, 15, 2017 causes the difference of 0.5 cycles ISB between BDS GEO and non-GEO satellites. By comparing the three dynamic models which include white noise process, random walk process, and random constant in the parameter estimation method, the ISB determined by the random constant model is consistent with the value obtained by the direct rounding method. After the calibration of ISBs, the performances of tightly combined positioning are assessed. The success rate of ambiguity resolution and accuracy of positioning for the tight combination (TC) are significantly improved in comparison with that for the loose combination (LC) over short baselines. For L5/E5a, on which only few satellites can be observed, the maximum increase in success rates of ambiguity resolution can reach 31.7%, i.e., from 54.9% of LC to larger than 86.6% of TC, and the positioning accuracies can even be increased by 0.13 m, i.e., from 0.208 of LC to 0.074 m of TC in East direction for the mix-receiver TRIMBLE NETR9-SEPT POLARX4 in 2018.     

A two-step robust adaptive filtering algorithm for GNSS kinematic precise point positioning

In kinematic navigation and positioning, abnormal observations and kinematic model disturbances are one of the key factors affecting the stability and reliability of positioning performance. Generally, robust adaptive filtering algorithm is used to reduce the influence of them on positioning results. However, it is difficult to accurately identify and separate the influence of abnormal observations and kinematic model disturbances on positioning results, especially in the application of kinematic Precise Point Positioning (PPP). This has always been a key factor limiting the performance of conventional robust adaptive filtering algorithms. To address this problem, this paper proposes a two-step robust adaptive filtering algorithm, which includes two filtering steps: without considering the kinematic model information, the first step of filtering only detects the abnormal observations. Based on the filtering results of the first step, the second step makes further detection on the kinematic model disturbances and conducts adaptive processing. Theoretical analysis and experiment results indicate that the two-step robust adaptive filtering algorithm can further enhance the robustness of the filtering against the influence of abnormal observations and kinematic model disturbances on the positioning results. Ultimately, improvement of the stability and reliability of kinematic PPP is significant.     

微分法在定位误差分析与计算中的应用

介绍了微分法分析计算定位误差的原理和适用范围,通过生产实例分析,证明了该方法在解决多误差因素定位误差分析与计算中的简便与快捷,从而有效简化了复杂定位方案定位误差的分析与计算,提高了夹具的设计效率。     

载波相位辅助的GPS动态单点定位算法综述

对载波相位辅助条件下应用于全球定位系统（Global Positioning System，GPS）动态单点定位的各种算法进行了综合分析与比较。首先简要介绍定位算法中的基本公式与观测模型；然后分别对周跳修复与滤波解算两部分所应用的各种算法进行详细介绍并比较其性能与适用范围；最后对尚待解决的问题及可能的发展方向进行了总结。     

Carrier phase prediction method for GNSS precise positioning in challenging environment

Since the signals of global navigation satellite system (GNSS) are blocked frequently in challenging environments, the discontinuous carrier phases seriously affect the application of GNSS precise positioning. To improve the carrier phase continuity, this paper proposes a carrier phase prediction method based on carrier open-loop tracking. In the open-loop tracking mode, the carrier numerically controlled oscillator (NCO) is controlled by the predicted Doppler, but not by the loop filter output. To improve the phase prediction effective time, accurate receiver clock drift estimation is studied in the prediction method. The phase prediction performance is tested on GNSS software receiver. In the phase prediction effective time tests, open-loop processes were set for the tested channel. The test results show that, when some satellite signals are blocked in 15?s, the probability of carrier phase error less than quarter cycles is more than 94%. In the real time kinematic (RTK) positioning tests, some satellite signals are blocked in 10–15?s repeatedly. The test results show that, the carrier phase continuity is basically not affected by the signal interruption, and the RTK can almost keep continuous centimeter-level positioning accuracy without re-fixing the integer ambiguity.     

Real-time clock comparison and monitoring with multi-GNSS precise point positioning: GPS,GLONASS and Galileo

The precise point positioning (PPP) technique is widely used in time and frequency applications. Because of the real-time service (RTS) project of the International GNSS Service, we can use the PPP technique for real-time clock comparison and monitoring. As a participant in the RTS, the Centre National d’Etudes Spatiales (CNES) implements the PPPWIZARD (Precise Point Positioning with Integer and Zero-difference Ambiguity Resolution Demonstrator) project to validate carrier phase ambiguity resolution. Unlike the Integer-PPP (IPPP) of the CNES, fixing ambiguities in the post-processing mode, the PPPWIZARD operates in the real-time mode, which is also called real-time IPPP (RT-IPPP). This paper focuses on applying the RT-IPPP for real-time clock comparison and monitoring. We review the principle of real-time clock comparison and monitoring, and introduce the methodology of the RT-IPPP technique. The observations of GPS, GLONASS and Galileo were processed for the experiments. Five processing modes were provided in the experiment to analyze the benefits of ambiguity resolution and multi-GNSS. In the clock comparison experiment, the average reduction ratios of standard deviations with respect to the G PPP mode range from 9.7% to 35.0%. In the clock monitoring experiment, G PPP mode can detect clock jumps whose magnitudes are larger than 0.9 ns. The RT-IPPP technique with GRE PPP AR (G) mode allows for the detection of any clock jumps larger than 0.6 ns. For frequency monitoring, G PPP mode allows detection of frequency changes larger than 1.1 × 10⁻¹⁴. When the RT-IPPP technique is applied, monitoring with GRE PPP AR (G) mode can detect frequency changes larger than 6.1 × 10⁻¹⁵.     

Evaluation of a regional real-time precise positioning system based on GPS/BeiDou observations in Australia

The performance of real-time (RT) precise positioning can be improved by utilizing observations from multiple Global Navigation Satellite Systems (GNSS) instead of one particular system. Since the end of 2012, BeiDou, independently established by China, began to provide operational services for users in the Asia-Pacific regions. In this study, a regional RT precise positioning system is developed to evaluate the performance of GPS/BeiDou observations in Australia in providing high precision positioning services for users. Fixing three hourly updated satellite orbits, RT correction messages are generated and broadcasted by processing RT observation/navigation data streams from the national network of GNSS Continuously Operating Reference Stations in Australia (AUSCORS) at the server side. At the user side, RT PPP is realized by processing RT data streams and the RT correction messages received. RT clock offsets, for which the accuracy reached 0.07 and 0.28?ns for GPS and BeiDou, respectively, can be determined. Based on these corrections, an accuracy of 12.2, 30.0 and 45.6?cm in the North, East and Up directions was achieved for the BeiDou-only solution after 30 min while the GPS-only solution reached 5.1, 15.3 and 15.5?cm for the same components at the same time. A further improvement of 43.7, 36.9 and 45.0 percent in the three directions, respectively, was achieved for the combined GPS/BeiDou solution. After the initialization process, the North, East and Up positioning accuracies were 5.2, 8.1 and 17.8?cm, respectively, for the BeiDou-only solution, while 1.5, 3.0, and 4.7?cm for the GPS-only solution. However, we only noticed a 20.9% improvement in the East direction was obtained for the GPS/BeiDou solution, while no improvements in the other directions were detected. It is expected that such improvements may become bigger with the increasing accuracy of the BeiDou-only solution.     

导管装焊精确定位柔性辅助系统的设计与开发

针对运载火箭增压输送系统中的拼焊型管路产品，以实现管路产品焊接的柔性装配为最终目标，开展了装焊精确定位柔性辅助系统的设计与开发。根据拼焊型管路的传统制造模式，焊接装配是采用专用装焊工装保证导管的空间走向和总体尺寸，因而每项导管对应一套专用装焊工装，管路结构的调整将导致原工装的返修甚至报废，造成生产成本高且严重影响导管的研制周期，该问题在研制型号中尤为突出。随着型号越来越多，专用装焊工装数量也显著增多，给工装管理也带来了极大的挑战。本文通过装焊精确定位柔性辅助系统的设计与开发，以导管特征点的坐标为控制指令实现柔性装配系统按照装配要求进行精确走位和定位，以柔性化的装配系统实现不同规格、不同空间走向的拼焊型管路产品的焊接装配。