逆向进气复合角发散冷却孔流量系数试验

针对回流燃烧室外环壁面冷气与燃气流动方向相反的情况,试验研究了发散孔进气方向与环腔通道气流流动方向相反的条件下,复合角发散冷却孔流量系数随发散孔倾角(25°~55°)、偏角(90°~180°)及压降系数等参数的变化规律。研究结果表明:复合角发散孔的流量系数随倾角的增大而增大,随偏角的增大而减小；随着压降系数的增大,复合角发散孔的流量系数先呈近似线性增长,当压降系数大于0.95后,呈非线性增长且增长速度减缓。      

针栓式推力室冷却特性试验研究

针栓式发动机具有推力调节简单、声学燃烧稳定性好和成本低廉等一系列优点,但目前对针栓式推力室的冷却特性掌握还不够深入,研制过程中曾多次出现因推力室冷却组织不好而烧蚀的问题。采用针栓式推力室试验件,对身部的冷却特性进行了深入研究,结果表明:推力室圆柱段前端的温度较低,无需采用专门的冷却措施;末端内侧气壁温度会达到约1650℃,局部存在明显的烧蚀现象,必须采取有效的热防护措施;下游冷却液膜量的变化对圆柱段的冷却特性影响较小。     

Flow mechanism between purge flow and mainstream in different turbine rim seal configurations

The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.     

高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

为了研究高主流湍流度下二次流密度比对涡轮导叶全气膜冷却特性的影响,使用热色液晶测量了在主流湍流度为15%,二次流密度比为1.0和1.5下三维涡轮导叶的气膜冷却效率和换热系数。二次流与主流质量流量比为7.0%和12.5%。结果表明:二次流密度比增大可以降低冷气射流的动量,小流量比工况下,在叶片前缘和压力面前半段,动量较低的二次流在高主流湍流度的影响下更易耗散,增大二次流密度比使冷却效率明显降低;大流量比工况下,二次流动量降低使气膜孔后区域冷气贴附性增强,气膜冷却效率和冷气覆盖效果均得到提升。小流量比工况下,二次流密度比增大对叶片表面换热的影响较小;大流量比工况下,二次流密度比增大使吸力面中弦区域和压力面后半段的平均换热系数比分别降低15%和25%。     

涡轮导向叶片综合冷却效率实验研究

为了研究流动参数对涡轮导向叶片综合冷却效率的影响,采用红外热像仪对叶片表面的温度分布进行了测量,得到了叶片的综合冷却效率随流量比、温比、主流进口雷诺数和湍流度的变化规律。实验过程中,次流与主流的流量比分别为0.15,0.18,0.20,0.22和0.24;主次流温比分别为1.4,1.7,1.93和2.2;主流进口雷诺数分别为1.0×10~5,1.1×10~5,1.2×10~5,1.3×10~5和1.4×10~5;主流进口湍流度分别为0.506%,8.156%,14.92%。结果表明,综合冷却效率在前缘处最低,沿流向逐渐升高;增大流量比会显著提高叶片的综合冷却效率,在温比为1.93时,流量比由0.15增大至0.24,综合冷却效率平均增加29.3%;温比和主流进口湍流度的增大均不利于综合冷却效率的提升,流量比为0.20时,温比由1.4增大至2.2,综合冷却效率平均下降46.5%,湍流度由0.506%增大至14.92%,综合冷却效率平均降低15.5%;主流进口雷诺数对叶片综合冷却效率的影响很小。     

Generalized Kutta–Joukowski theorem for multi-vortex and multi-airfoil flow with vortex production——A general model

By using a special momentum approach and with the help of interchange between singularity velocity and induced flow velocity, we derive in a physical way explicit force formulas for twodimensional inviscid flow involving multiple bound and free vortices, multiple airfoils, and vortex production. These force formulas hold individually for each airfoil thus allowing for force decomposition, and the contributions to forces from singularities(such as bound and image vortices,sources, and doublets) and bodies out of an airfoil are related to their induced velocities at the locations of singularities inside this airfoil. The force contribution due to vortex production is related to the vortex production rate and the distance between each pair of vortices in production, thus frameindependent. The formulas are validated against a number of standard problems. These force formulas, which generalize the classic Kutta–Joukowski theorem(for a single bound vortex) and the recent generalized Lagally theorem(for problems without a bound vortex and vortex production) to more general cases, can be used to identify or understand the roles of outside vortices and bodies on the forces of the actual body, optimize arrangement of outside vortices and bodies for force enhancement or reduction, and derive analytical force formulas once the flow field is given or known.     

改善横向波纹隔热屏综合冷却效率的发散冷却结构优化

为改善横向波纹隔热屏综合冷却效果，采用三维数值模拟和基于支持向量机的代理优化模型，在给定的单位面积冷却空气流量下对发散冷却结构参数进行了优化研究。设计变量选取为气膜孔直径、气膜孔排布的展向间距和流向间距，以面积平均综合冷却效率作为目标函数，通过遗传算法搜索获得了设计变量区间内的优化设计点。在隔热屏单位表面积冷却空气流量G_f = 2.647 kg/（m²?s）的工况下，优化后的d、P和S分别为0.8、4和5 mm。研究结果表明，优化的隔热屏冷却结构应具有较小的气膜孔直径d和展向间距P，以及适中的流向间距S。相对于参考结构，优化后的发散冷却结构能够改善沿流向的气膜覆盖，缩减发散冷却起始段局部高温段，起到增强隔热屏发散冷却综合冷却效率的作用。     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.     

纵向波纹隔热屏气膜冷却特性实验

针对加力燃烧室纵向波纹隔热屏气膜冷却效果开展了细致的实验研究,利用红外热像仪测量了隔热屏壁面的温度分布,分析了隔热屏板型、吹风比、开孔率等参数对气膜冷却效率的影响。实验中板型选取了平板和纵向波纹隔热屏,吹风比变化范围是0.5~3.0,开孔率变化范围是1.4%~3.7%。结果表明:相比于平板隔热屏的气膜冷却效率沿程逐渐增加,纵向波纹隔热屏的气膜冷却效率随波纹板的起伏而起伏且大于平板隔热屏;随着吹风比的增加气膜冷却效率逐渐加大,在吹风比为3.0时达到最大值;气膜冷却效率在波峰处低,波谷处高,整体上随波纹板的起伏而波动,吹风比越小,气膜冷却效率随波纹板的起伏变化越明显;高吹风比(吹风比为2.0~3.0)下,气膜冷却效率沿程变化与增幅较为缓慢;整体上,随着开孔率的增加气膜冷却效率逐渐加大,小开孔率(开孔率为1.4%、2.7%)下的气膜冷却效率相差不大,但在次流背风侧,开孔率小的气膜冷却效率要小于开孔率大的气膜冷却效率。      

短螺旋型燃烧室旋流结构及气动边界发展规律数值模拟研究

短螺旋型燃烧室的头部轴线沿发动机周向与发动机轴线偏转一定角度,可以在保证燃烧效率不变的条件下有效缩短燃烧室轴向长度。短螺旋型燃烧室流场的最大特点是旋流流动单侧受限。为了研究头部安装角α变化对燃烧室旋流流动特性的影响,基于数值方法对短螺旋型燃烧室进行了计算分析。结果表明:随着α变化,旋流器下游旋涡依次出现对称环状、马蹄状、环状结构;随着α增加,气动边界逐渐出现并抑制旋流的周向扩张,导致流场出现不同的旋涡结构;不同α下的切向角动量随轴向距离增加而衰减,但α为35°和45°时,气动边界在非受限侧出现并对旋流产生约束,角动量衰减变慢;当α为0°,15°,35°,45°时,燃油液滴依次集中分布在旋流器下游两旋涡边缘、侧壁面和头部端壁、非受限旋涡边缘。本文研究了不同α下的旋涡结构及气动边界沿轴向的演化过程,为短螺旋型燃烧室进一步的设计与优化提供基础。