Quantitative assessment and visualization of flight risk induced by coupled multi-factor under icing conditions

Aircraft icing has been proven to be one of the most serious threats to flight safety. During the analysis of flight risk under icing conditions, quantitative assessment and visualization of flight risk are quite essential as they provide safe manipulation strategies in intricate conditions. However, they are rarely studied. Since the icing flight accidents are the result of the coupling of multiple unfavorable factors, in present study, we have proposed a method to quantitatively assess flight risk induced by multi-factor coupling under icing conditions by Monte-Carlo simulation and multivariate extreme value theory. The results demonstrate that the flight risk probability increases with the rise of unfavorable factors. Besides, a flight risk visualization method named flight safety window has been presented to build the flight risk distribution cloud maps in different complex conditions. The cloud maps show that the icing would give rise to atrophy of the safety scope, and the consequence would be even more severe when coupled with other more unfavorable factors. The proposed methods in this study would be useful in flight risk analysis under icing conditions and can enhance the pilot's situational awareness in selecting correct strategies within the safety zone to avoid unsafe manipulation.     

液体火箭发动机诱导轮空化热力学效应研究

为了研究空化热力学效应,以模型诱导轮为研究对象,改变流量、水温等条件,对其内部空化流动进行了可视化实验研究,完整记录了从空化初生至性能断裂点各工况的空化区形态。结果表明:温度对诱导轮无空化水力性能没有显著影响,但是高温下诱导轮的空化性能断裂点被显著延后,体现了热力学效应的影响。对比不同温度下的空化区形态,发现热力学效应的强弱与流动工况密切相关,在小空化数下体现得更为显著。同时引入一种半经验的理论模型预测热效应对空化性能的影响,小流量(Φ=0.071)下预测结果与实验结果平均偏差为5.5%,大流量(Φ=0.088)下平均偏差为10.8%,验证了模型在本文应用条件下的可靠性。     

端壁抽吸位置对大转角扩压叶栅流场及负荷的影响

实验研究了低速条件下在端壁近吸力面处进行附面层吸除对某大转角扩压叶栅性能的影响.对叶栅出口截面参数和叶片型面静压进行了测量,并在叶片表面及端壁进行了墨迹流动显示.结果表明,端壁抽吸主要影响了吸力面/端壁角区,重新分配叶片根部负荷.在角区未发生分离的位置开始抽吸可有效推迟叶栅内的角区分离,降低损失,改善叶栅端区流动;而在角区已经发生分离的弦向位置开槽吸气则引起了局部回流,恶化了流场,增加了低能流体的掺混和气动损失.     

双涵道S形弯管气动性能的数值研究

环型双涵道S形弯管是涡轮风扇发动机中连接风扇和高压压气机的重要部件。采用有限容积法对双涵道S形弯管在不同进气条件下的流场进行了数值研究。计算过程中使用两种不同的湍流模型：标准k-ε模型和雷诺应力模型。通过对比可以发现两种湍流模型的计算结果有着明显的差别,尤其是在存在较强剪切应力的区域。此外,还对不同的进气条件（环形管流和均匀来流）对S弯管流场的影响进行了分析。可以看出,不同进气条件中附面层速度剖面的不同能够影响S弯管中轴向速度的分布与发展。     

斜流压气机扩压器设计和流场的数值模拟研究

以匹配某高增压比斜流叶轮为目标,设计了Z15、Z16和Z17三个扩压器方案,然后以斜流级（斜流叶轮＋扩压器）为研究对象,展开了三维粘性数值模拟研究,分析了不同方案扩压器的总体性能以及内部流场结构。研究结果表明,设计方案满足匹配斜流叶轮的目标,三种方案的整级最大绝热效率均超过82％,最大总压比超过5．6,大多数工况点的静压恢复系数大于0．6,总压恢复系数大于0．92。其中．Z16方案气动性能最优。     

进气条件对压气机中介机匣流场影响的试验研究

以某压气机中介机匣为试验研究对象,通过改变来流径向分布与马赫数,建立了评估中介机匣气动性能的进口约束条件。在同步测量轴向流路离散压力参数的基础上,分析了中介机匣内部流场对进气条件的稳态响应。研究结果表明:进气条件对中介机匣流动损失影响较大,与均匀进气相比,进气畸变会增大弯曲流道内部径向压力梯度,影响流道曲率与流向压力梯度对附面层的控制效果;支板尾流对通道主流的干扰导致下游平直流道上部区域流场恶化,而进气畸变会加剧支板尾迹的影响;随着进口马赫数的增大,中介机匣总压损失系数与总压畸变强度呈现出不同的增长趋势,其出口流场径向分布对马赫数变化的气动敏感性较高。     

采用机头边条改善飞机大迎角横侧气动特性的风洞试验研究

飞机大迎角横侧气动特性是决定其机动性及敏捷性的主要因素之一。本文就采用机头边条改善飞机大迎角横侧气动特性进行了讨论。着重对机头边条的大小、安装位置等对飞机稳定性的影响进行讨论。试验是在气动中心低速所４ｍ×３ｍ和３．２ｍ风洞中进行的。     

对转压气机数值模拟及实验研究

以设计的某对转压气机试验台为研究对象,分别应用数值模拟和试验手段对设计转速、典型工作状态下压气机性能和流场细微结构进行了研究。计算结果表明:压气机压比特性与试验值吻合较好,计算效率较试验值偏高;在近失速点压气机第二排转子叶片吸力面近尖部10%叶展范围内,最先出现导致叶片失速的大范围分离和低能堵塞团;第一排转子叶片尖部尾缘处附面层较厚并伴随有分离现象,使得下游叶片来流发生较大畸变。     

腹下无隔道大偏距跨声速S弯进气道气动特性的实验研究(英文)

An investigation on the ventral diverterless high offset S-shaped inlet is carried out at Mach numbers from 0.600 to 1.534, angles of attack from -4° to 9.4°, and yaw angles from 0° to 8°. Results indicate： （1） a large region of low total pressure exists at the lower part of the inlet exit caused by the counter-rotating vortices in the S-shaped duct; （2） the performances of the inlet at Mach number 1.000 reach almost the highest, so the propulsion system could work efficiently in terms of aerodynamics; （3） the total pressure recovery increases slowly at first and then remains unvaried as the Mach number rises from 0.6 to 1.0, however, it does in an opposite manner in the conventional diverter-equipped S-shaped inlet; （4） the performances of the inlet are generally insensitive to angles of attack from -4° to 9.4° and yaw angles from 0° to 8° at Mach number 0.850, and angles of attack from -2° to 6° and yaw angles from 0° to 5° at Mach number 1.534.     

对航天职工薪酬满意度调查的分析

本文介绍了航天某军民结合型研究所现行的薪酬结构和分配办法,通过对单位员工的薪酬满意度调查,分析该薪酬结构的特点与不足,为下一步的薪酬设计奠定基础。