叶片式预旋喷嘴出口流场实验研究

叶片式预旋喷嘴具有尺寸小,落后角大的特点。为了详细研究小尺寸预旋喷嘴的预旋性能,采用五孔探针对叶片式预旋喷嘴的出口流场进行了实验研究。测量了Ma=0.2,0.3时喷嘴出口的压力分布、速度分布和出口气流角度分布,实验获得了喷嘴的落后角和预旋效率,并进行了与实验工况相同的数值计算。通过实验获得的总压云图以及速度云图,可以发现叶片式预旋喷嘴的端壁二次流损失、尾迹损失严重,有明显的边界层分离现象。Ma=0.2时,喷嘴Re数为5.76×104,落后角2.84°,实验测得的预旋效率为0.73;Ma=0.3时,喷嘴Re数为1.06×105,预旋效率提高至0.77。实验模型端壁的影响使预旋效率实验结果偏低6.5%左右。数值结果与实验测得各参数符合较好:数值结果与测得的喷嘴出口截面平均总压、静压偏差在1%以内;出气速度、周向速度以及出气角度与实验结果偏差在4%以内。数值计算表明,叶片式预旋喷嘴的预旋效率基本不受压比影响,随Re数增大先增大后基本不变,最后基本稳定在0.85。     

逆向进气复合角发散冷却孔流量系数试验

针对回流燃烧室外环壁面冷气与燃气流动方向相反的情况,试验研究了发散孔进气方向与环腔通道气流流动方向相反的条件下,复合角发散冷却孔流量系数随发散孔倾角(25°~55°)、偏角(90°~180°)及压降系数等参数的变化规律。研究结果表明:复合角发散孔的流量系数随倾角的增大而增大,随偏角的增大而减小；随着压降系数的增大,复合角发散孔的流量系数先呈近似线性增长,当压降系数大于0.95后,呈非线性增长且增长速度减缓。      

基于自适应差分进化算法的变循环发动机模型求解方法研究

为了降低传统迭代算法在求解变循环发动机非线性模型时对初值的依赖性,将模型的求解问题转换为求最小值的优化问题,引入差分进化算法进行模型的求解,并提出一种自适应差分进化算法(ADE)。ADE借助轮盘赌选择法,利用种群的进化经验可以自适应的选择最适合当前种群的差分策略与算法控制参数。针对变循环发动机四个典型工作点的模型求解问题,研究了标准差分进化算法(SDE)的控制参数对其性能的影响,获取了SDE在求解四个典型工作点时的最优控制参数组合,对比分析了ADE与SDE的性能差异,最后研究了种群规模对ADE性能的影响。结果表明：SDE在求解发动机模型时具有较好的鲁棒性,在求解不同工作点时算法的最优控制参数并不完全相同；相比于使用最优控制参数的SDE,ADE可以在不影响算法鲁棒性的情况下提升效率50%以上；减少ADE的种群规模会在提升算法效率的同时破坏鲁棒性。     

High-fidelity trajectory optimization for aeroassisted vehicles using variable order pseudospectral method

In this study, the problem of time-optimal reconnaissance trajectory design for the aeroassisted vehicle is considered. Different from most works reported previously, we explore the feasibility of applying a high-order aeroassisted vehicle dynamic model to plan the optimal flight trajectory such that the gap between the simulated model and the real system can be narrowed. A highly-constrained optimal control model containing six-degree-of-freedom vehicle dynamics is established. To solve the formulated high-order trajectory planning model, a pipelined optimization strategy is illustrated. This approach is based on the variable order Radau pseudospectral method, indicating that the mesh grid used for discretizing the continuous system experiences several adaption iterations. Utilization of such a strategy can potentially smooth the flight trajectory and improve the algorithm convergence ability. Numerical simulations are reported to demonstrate some key features of the optimized flight trajectory. A number of comparative studies are also provided to verify the effectiveness of the applied method as well as the high-order trajectory planning model.     

考虑捷联导引头最小视场角约束的制导策略

针对高超声速飞行器捷联导引头，提出导引头最小视场角（FOV）约束问题。首先分析了导引头视线角变化规律，指出在攻击固定目标时，导引头最小视场角约束在弹道末段无法被满足，导引头将丢失目标。在此基础上，基于缩短导引头丢失目标距离的目标，提出一种满足导引头最小视场角约束的制导策略。该策略不依赖于末制导律形式，当最小视场角约束无法被满足时，改变原有制导指令，主动改变弹道轨迹以增加弹体视线角，避免超出视场范围。其次，针对飞行器过载约束，设计了制导策略切换点，在到达切换点时该制导策略将结束工作，避免末端过载过大超出约束。通过对比仿真验证了所提出制导策略有效性，能够大幅度减少导引头丢失目标距离，工程上有利于提高末端命中精度。     

变攻角下被动射流旋涡对高速扩压叶栅性能的影响

对被动射流旋涡(PJV)控制高速扩压叶栅内的流动分离控制展开数值研究,并探究其在变工况条件下的适应特性。结果表明,PJV在设计攻角下可使叶栅总压损失系数降低5.2%,变攻角条件下的损失降低幅度最高可达7.8%,表明其具有较高的控制效率和良好的变工况适应特性。随着攻角的增大,吸力面分离位置提前,射流出口与分离区间的距离减小,PJV能够更为有效地促进附面层内低能流体与主流间的动量交换,使得壁面涡结构得到重新组织,并进一步影响通道涡、集中脱落涡等涡系结构的发展,从而推迟流动分离、减小损失。在综合考虑变攻角流场特性的前提下,应使PJV的作用位置位于分离区上游不远处,所研究的最佳射流位置位于叶片前缘上游40%轴向弦长处。      

Designing method of acceleration and deceleration control schedule for variable cycle engine

Studies show that different geometries of a Variable Cycle Engine (VCE) can be adjusted during the transient stage of the engine operation to improve the engine performance. However, this improvement increases the complexity of the acceleration and deceleration control schedule. In order to resolve this problem, the Transient-state Reverse Method (TRM) is established in the present study based on the Steady-state Reverse Method (SRM) and the Virtual Power Extraction Method (VPEM). The state factors in the component-based engine performance models are replaced by variable geometry parameters to establish the TRM for a double bypass VCE. Obtained results are compared with the conventional component-based model from different aspects, including the accuracy and the convergence rate. The TRM is then employed to optimize the control schedule of a VCE. Obtained results show that the accuracy and the convergence rate of the proposed method are consistent with that of the conventional model. On the other hand, it is found that the new-model-optimized control schedules reduce the acceleration and deceleration time by 45% and 54%, respectively. Meanwhile, the surge margin of compressors, fuel–air ratio and the turbine inlet temperature maintained are within the acceptable criteria. It is concluded that the proposed TRM is a powerful method to design the acceleration and deceleration control schedule of the VCE.     

航空发动机离心式喷嘴宏观喷雾特性

为探究航空发动机离心式喷嘴的喷雾宏观特性，通过将该喷嘴在高温高压定容弹中进行喷雾过程的实验，并结合阴影法与纹影法进行光学测量。首先以水作为射流工质，观察不同喷射压力下水进入大气环境中的雾化角变化，发现喷嘴结构对雾化角有着重要影响，最大雾化角与喷嘴出口的导流结构夹角相等。其次以正癸烷作为工质，通过不同环境压力和温度下的多组实验测量其它喷雾宏观特性如液膜破碎长度，结果表明在背压大于1.75MPa的工况下，该离心式喷嘴无法形成清晰稳定的锥形喷雾结构，此外还揭示了高背压加强了气动力而高环境温度减小了表面张力和粘性力，两者都起着促进雾化的作用。     

Statistical characteristics of low latitude Pc4s: Influence of solar wind and IMF parameters

Pc4 signatures for the year 2013, extracted from geomagnetic north–south and east–west components of induction coil magnetometer (LEMI 30) from low latitude station Desalpar (DSP), operated by Institute of Seismological Research (ISR), India have been investigated vis-à-vis the prevalent interplanetary parameters (IMF) as well as the geomagnetic activity indices. A clear dominance of Pc4-5 (467 events) over Pc3 (17 events) is observed. Local time variation of Pc4 shows a peak in the noon sector in both X and Y components. Our investigations show that the dominant peak frequency is 10 mHz at low latitude region. Correlations with solar wind and IMF parameters illustrate highest occurrence of Pc4 for a solar wind speed of 300–400 km/s and average IMF B field of 3–6 nT. The amplitude of Pc4s at DSP shows an increase with increasing solar wind speed, plasma density, solar wind dynamic pressure and average B field which is also reflected in the trend of frequency variation of these pulsations. We report that IMF clock angle at low latitude does not have influence on Pc4 occurrence. Based on the characteristics of these events, detected in latitudinally distributed stations from low and mid-latitudes from northern and southern hemisphere, we infer that modes were compressional, which could be driven by K-H instability or solar wind dynamic pressure, as compressional modes can propagate to low latitude with little attenuation.     

基于微型涡喷发动机热喷流的无源流体推力矢量喷管的控制规律

流体推力矢量喷管型面固定、活动部件少、结构重量轻，能够为高机动飞行器提供有效的飞行控制手段，但无源流体推力矢量喷管热喷流的偏转控制规律尚未完全掌握。为了推进无源流体推力矢量技术的实用化，本文设计研制了适用于微型涡喷发动机的耐高温喷管模型，对该喷管在微型涡喷发动机热喷流状态下的控制规律进行研究。利用非接触光学显示和测量手段——红外热成像拍摄和粒子图像测速（PIV）技术对主射流流动特性进行研究，获得流动矢量角随二次流控制阀门闭合度变化的控制规律；利用六分量盒式天平测力实验研究无源流体推力矢量喷管的力学特性，获得推力矢量角随二次流控制阀门闭合度变化的控制规律。研究结果表明：该构型喷管在微型涡喷发动机热喷流下主射流连续可控偏转，最大流动矢量角为-12.3°/12.3°，最大推力矢量角为-12.9°/12.8°，控制规律接近线性，不存在主射流偏转突跳问题。