Effect of scavenge port angles on flow distribution and performance of swirl-loop scavenging in 2-stroke aircraft diesel engine

Swirl-Loop Scavenging (SLS) improves the performance of 2-stroke aircraft diesel engine because the involved swirl may not only benefit the scavenging process, but also facilitate the fuel atomization and combustion. The arrangement of scavenge port angles greatly influences in-cylinder flow distribution and swirl intensity, as well as the performance of the SLS engine. However, the mechanism of the effect and visualization experiment are rarely mentioned in the literature. To further investigate the SLS, Particle Image Velocimetry (PIV) experiment and Computational Fluid Dynamics (CFD) simulation are adopted to obtain its swirl distribution characteristics, and the effect of port angles on scavenging performance is discussed based on engine fired cycle simulation. The results illustrate that Reynolds Stress Turbulence model is accurate enough for in-cylinder flow simulation. Tangential and axial velocity distribution of the flow, as well as the scavenging performance, are mainly determined by geometric scavenge port angles α_geom and β_geom. For reinforcement of scavenging on cross-sections and meridian planes, α_geom value of 27° and β_geom value of 60° are preferred, under which the scavenging efficiency reaches as high as 73.7%. Excessive swirl intensity has a negative effect on SLS performance, which should be controlled to a proper extent.     

基于Deform软件二次开发和BP神经网络的TA15多向锻造微观组织预报

通过热压缩实验构建了TA15合金的热变形真应力-应变曲线，以此为基础分别建立了合金双相区及单相区温度区间的热变形本构方程；基于热压缩试样动态再结晶的统计数据建立了TA15合金的动态再结晶模型。借助Deform提供的二次开发功能实现相关数学模型的程序化，制定正交实验方案，实现了TA15合金多向锻造变形的微观组织仿真。通过正交实验分析得出各项因子的影响对象及强弱差异，提出了双相区及单相区温度区间内的多向锻造最佳因子组合。建立了TA15合金多向锻造变形微观组织的BP （Back Propagation）神经网络预测模型，将预测结果与有限元仿真结果进行比较，结果表明两种方法的预测结果基本一致，但神经网络具备有限元仿真难以实现的良好细节预测能力，能更为细致地实现对微观组织分布状态的划分。     

Cutting path-dependent machinability of SiCp/Al composite under multi-step ultra-precision diamond cutting

Particle-tool interactions, which govern the synergetic deformation of SiC particle reinforced Al matrix composites under mechanical machining, strongly depend on the geometry of particle position residing on cutting path. In the present work, we investigate the influence of cutting path on the machinability of a SiCp/Al composite in multi-step ultra-precision diamond cutting by combining finite element simulations with experimental observations and characterization. Be consistent with experimentally characterized microstructures, the simulated SiCp/Al composite is considered to be composed of randomly distributed polygonally-shaped SiC particles with a volume fraction of 25vol%. A multi-step cutting strategy with depths of cut ranging from 2 to 10 μm is adopted to achieve an ultimate depth of cut of 10 μm. Intrinsic material parameters and extrinsic cutting conditions utilized in finite element simulations of SiCp/Al cutting are consistent with those used in corresponding experiments. Simulation results reveal different particle-tool interactions and failure modes of SiC particles, as well as their correlations with machining force evolution, residual stress distribution and machined surface topography. A detailed comparison between numerical simulation results and experimental data of multi-step diamond cutting of SiCp/Al composite reveals a substantial impact of the number of cutting steps on particle-tool interactions and machined surface quality. These findings provide guidelines for achieving high surface finish of SiCp/Al composites by ultra-precision diamond cutting.     

Spacecraft formation flying control around L2 sun-earth libration point using on–off SDRE approach

In this paper, on–off SDRE control approach is presented for spacecraft formation flying control around sun-earth L2 libration point. Orbits around libration points are significant targets for many space missions mainly because of efficient fuel consumption. Furthermore, less propellant usage can be achieved by considering optimal control approaches in spacecraft formation flying control design. Among various nonlinear and optimal control methods, SDRE has shown to be a popular controller in various missions due to the privileges including efficiency, accuracy and robustness. The spacecraft are assumed to have on–off thrusters as actuators. It requires them to be fed with a sequence of on–off pulses which is regarded as a challenge for spacecraft designers. Hence, the main contribution of this paper is designing an on–off SDRE approach for the formation flight around sun-earth L2 point with uncertainty with energy and accuracy considerations. Including on–off input as a constraint is not feasible for SDRE implementation because it makes the system non-affine. An alternative is utilizing an integral action technique and an auxiliary control to make the system affine which leads to on–off SDRE approach. It has also been shown that the proposed method is robust against parametric uncertainties of the states. Present study aims to design an energy-beneficial, simple and attractive controller for a complex nonlinear system with on–off inputs and uncertainty in CRTBP. Simulation results show that the on–off SDRE control could provide the formation flight around L2 point with high accuracy using less energy consumption.     

Ionospheric total electron content response to annular solar eclipse on June 21, 2020

The effects of physical events on the ionosphere structure is an important field of study, especially for navigation and radio communication. The paper presents the spatio-temporal ionospheric TEC response to the recent annular solar eclipse on June 21, 2020, which spans across two continents, Africa and Asia, and 14 countries. This eclipse took place on the same day as the June Solstice. The Global Navigation Satellite System (GNSS) based TEC data of the Global Ionosphere Maps (GIMs), 9 International GNSS Service (IGS) stations and FORMOSAT-7/COSMIC-2 (F7/C2) were utilized to analyze TEC response during the eclipse. The phases of the TEC time series were determined by taking the difference of the observed TEC values on eclipse day from the previous 5-day median TEC values. The results showed clear depletions in the TEC time series on June 21. These decreases were between 1 and 9 TECU (15–60%) depending on the location of IGS stations. The depletions are relatively higher at the stations close to the path of annular eclipse than those farther away. Furthermore, a reduction of about ?10 TECU in the form of an equatorial plasma bubble (EPB) was observed in GIMs at ~20° away from the equator towards northpole, between 08:00–11:00 UT where its maximum phase is located in southeast Japan. Additionally, an overall depletion of ~10% was observed in F7/C2 derived TEC at an altitude of 240 km (hmF2) in all regions affected by the solar eclipse, whereas, significant TEC fluctuations between the altitudes of 100 km ? 140 km were analyzed using the Savitzky-Golay smoothing filter. To prove TEC depletions are not caused by space weather, the variation of the sunspot number (SSN), solar wind (V_SW), disturbance storm-time (Dst), and Kp indices were investigated from 16th to 22nd June. The quiet space weather before and during the solar eclipse proved that the observed depletions in the TEC time series and profiles were caused by the annular solar eclipse.     

Equatorial anomaly according to the Interkosmos-19 data and IRI model: A comparison

The comparison of the IRI model with the foF2 distribution in the equatorial anomaly region obtained by topside sounding onboard the Interkosmos-19 satellite has been carried out. The global distribution of foF2 in terms of LT-maps was constructed by averaging Intercosmos-19 data for summer, winter, and equinox. These maps, in fact, represent an empirical model of the equatorial anomaly for high solar activity F10.7 ~ 200. The comparison is carried out for the latitudinal foF2 profiles in the characteristic longitudinal sectors of 30, 90, 210, 270, and 330°, as well as for the longitudinal variations in foF2 over the equator. The largest difference between the models (up to 60%) for any season was found in the Pacific longitudinal sector of 210°, where there are a few ground-based sounding stations. Considerable discrepancies, however, are sometimes observed in the longitudinal sectors, where there are many ground-based stations, for example, in the European or Indian sector. The discrepancies reach their maximum at 00 LT, since a decay of the equatorial anomaly begins before midnight in the IRI model and after midnight according to the Interkosmos-19 data. The discrepancies are also large in the morning at 06 LT, since in the IRI model, the foF2 growth begins long before sunrise. In the longitudinal variations in foF2 over the equator at noon, according to the satellite data, four harmonics are distinguished in the June solstice and at the equinox, and three harmonics in the December solstice, while in the IRI model only two and one harmonics respectively are revealed. In diurnal variations in foF2 and, accordingly, in the equatorial anomaly intensity, the IRI model does not adequately reproduce even the main, evening extremum.     

微等离子体转化二氧化碳发射光谱诊断

火星大气层的主要成分为二氧化碳，如果能够利用低温等离子体方法高效分解二氧化碳，使其转化为氧气和一氧化碳加以利用，可以大幅降低航天员生命保障相关载荷长途运输的成本，进一步提高生命保障能力。低温等离子体放电过程中会产生大量活性组分，可以在数百度温度下实现二氧化碳的高效解离，是具有很大潜力的二氧化碳解离与转化方式。设计了一种尺度在亚毫米级、功率输入为数瓦的直流微槽等离子体反应器，可以在较低气体温度下实现二氧化碳分解。测量了反应器电流、功率等放电参数，采用发射光谱确定了体系中激发态组分，分析了激发态粒子谱线强度随输入电压、稀释气体比例等反应器工作参数变化，利用氮气分子振转谱带测量了等离子体放电区振动温度和气体温度。研究表明，添加氩、氦、氮气均可以增强二氧化碳的分解，添加氦气可以促进二氧化碳的电离过程。稀释气体激发态因具有高能量，可以通过潘宁解离通道增强二氧化碳分解。氦组分激发态的能量高于二氧化碳电离能，可以促进二氧化碳的电离反应。微等离子体内存在强烈的振动 平动非平衡现象：振动温度约为4400~4800K，而气体温度仅为450 ~600K，表明可以通过合理的放电和结构设计，定向将能量注入到振动态，从而进一步促进二氧化碳的振动解离。     

阳极氧化对TiAl合金高温氧化行为和力学性能的影响

采用电化学阳极氧化技术在含NH4F的乙二醇电解液中对TiAl合金进行阳极氧化处理。研究阳极氧化对TiAl合金高温氧化行为和力学性能的影响。结果表明:由于“卤素效应”,阳极氧化处理的TiAl合金经高温氧化后表面形成致密、连续的Al₂O₃氧化膜,有效阻止了氧的内扩散,进而显著提高合金的抗高温氧化性能。经1000℃氧化100 h后,阳极氧化试样增重由未经阳极氧化处理试样的85.86 mg/cm²降至0.67 mg/cm²。另一方面,阳极氧化TiAl合金表面硬度和弹性模量随高温氧化时间延长呈先降低后升高的趋势。阳极氧化TiAl合金在高温服役后,合金的摩擦系数较未经阳极氧化处理试样上升,但表面耐磨性先降低后升高。这是由于TiAl合金经阳极氧化后,表面形成了一层富铝含氟氧化膜,由于氧化膜中F元素在高温氧化过程中与Ti、Al结合形成卤化物,卤化物蒸气选择性扩散在原始氧化膜处形成致密的Al₂O₃保护膜。阳极氧化对TiAl合金力学性能的影响主要是由于氧化膜中Al₂O₃的含量变化所致。     

模拟打伤/抛修缺口对TC17钛合金叶片振动疲劳性能的影响

研究了无缺口、打伤缺口和3种抛修缺口对TC17钛合金叶片振动疲劳性能的影响。结果表明,无缺口模拟叶片的疲劳寿命最长且寿命分散性最小,打伤缺口模拟叶片的疲劳寿命最短且寿命分散性最大,3种抛修缺口模拟叶片的疲劳寿命介于前两者之间,其中抛修缺口Ⅰ模拟叶片的疲劳寿命最长。无缺口和抛修缺口模拟叶片的疲劳裂纹均起源于叶片根部,打伤缺口模拟叶片的裂纹产生于缺口底部,与有限元模拟计算的最大应力位置吻合。模拟叶片的疲劳断裂区比较平坦,呈半椭圆形貌,疲劳源区主要位于模拟叶片表面的微小损伤处,疲劳扩展区具有典型的疲劳弧线特征,并呈现沿α/β片状组织界面开裂的特征。     

Evaluation of the IRI-2016 and NeQuick electron content specification by COSMIC GPS radio occultation,ground-based GPS and Jason-2 joint altimeter/GPS observations

We examined performance of two empirical profile-based ionospheric models, namely IRI-2016 and NeQuick-2, in electron content (EC) and total electron content (TEC) representation for different seasons and levels of solar activity. We derived and analyzed EC estimates in several representative altitudinal intervals for the ionosphere and the plasmasphere from the COSMIC GPS radio occultation, ground-based GPS and Jason-2 joint altimeter/GPS observations. It allows us to estimate a quantitative impact of the ionospheric electron density profiles formulation in several altitudinal intervals and to examine the source of the model-data discrepancies of the EC specification from the bottom-side ionosphere towards the GPS orbit altitudes. The most pronounced model-data differences were found at the low latitude region as related to the equatorial ionization anomaly appearance. Both the IRI-2016 and NeQuick-2 models tend to overestimate the daytime ionospheric EC and TEC at low latitudes during all seasons of low solar activity. On the contrary, during high solar activity the model results underestimated the EC/TEC observations at low latitudes. We found that both models underestimated the EC for the topside ionosphere and plasmasphere regions for all levels of solar activity. For low solar activity, the underestimated EC from the topside ionosphere and plasmasphere can compensate the overestimation of the ionospheric EC and, consequently, can slightly decrease the resulted model overestimation of the ground-based TEC. For high solar activity, the underestimated EC from the topside ionosphere and plasmasphere leads to a strengthening of the model underestimation of the ground-based TEC values. We demonstrated that the major source of the model-data discrepancies in the EC/TEC domain comes from the topside ionosphere/plasmasphere system.