刮削作用对涡轮转子机匣通道涡形成的影响

采用数值方法求解耦合剪切应力输运(SST)湍流模型的雷诺平均Navier-Stokes方程组,研究了不同间隙尺寸下GE-E3高压涡轮第一级转子内刮削作用对机匣通道涡形成和发展的影响。通过与轮毂通道涡结构的对比,发现机匣通道涡层次结构与经典二次流理论存在明显的差异,并对该差异形成的原因进行了深入探索。结果表明:叶顶对机匣边界层的刮削作用在机匣通道涡的形成过程中占主导作用,刮削作用使得流向叶片吸力面的来流机匣边界层在交汇点区域从内层向外层卷起,形成层次结构相反的机匣通道涡;叶顶浸入比值是影响转子机匣通道涡形成的重要参数,随着比值的增大,机匣通道涡损失先增大后减小;只有在间隙尺寸较大情况下,叶尖间隙的"抽吸作用"才能抑制机匣通道涡的发展。     

离心压气机失速模式及自循环机匣处理的作用机制

通过对离心压气机不同转速下实壁机匣和处理机匣两种状态流场的数值模拟,研究了失速模式随转速的变化及不同失速模式下机匣处理作用机制的转变.结果表明:随转速的降低,失速模式由100%设计转速时的扩压器失速逐步向导风轮失速过渡,导风轮失速也经历了由80%设计转速时的端壁失速和叶片前缘失速向50%设计转速的通道大范围完全失速的发展过程.自循环机匣处理对离心压气机失速裕度和效率的影响都与失速模式紧密相关,其扩稳作用仅对80%设计转速时的叶片前缘失速有效.在80%左右设计转速,机匣处理使主流效率有朝大流量工况点变化的趋势,从而使效率降低.当转速低至50%设计转速时,主流通道形成大范围回流区,机匣处理的二次回流可以减少叶轮对通道回流区气流的做功量,从而提高效率.     

穿过外涵机匣的管路结构设计

随着对航空发动机的引气、供油、点火、测试等功能要求的提高,穿过外涵机匣的传感器和管路数量大大增加,为降低外涵机匣拆装的难度,提高穿过外涵机匣的管路的可装配性,在原有管路的连接结构、密封结构、补偿结构、分解维护4个方面的结构设计基础上,设计了2种新型穿过外涵机匣的管路结构,新型管路具有结构简单、拆装便捷、安全可靠、互换性好等优点,可满足管路补偿和外涵机匣的密封要求。     

双层金属平板模拟机匣抗冲击性研究

采用LS-Dyna软件分析了双层平板模拟机匣的抗冲击性能,讨论了层间距和厚度分配对双层平板模拟机匣抗冲击性能的影响。研究结果表明：在叶片正撞击时,双层模拟机匣的损伤为局部剪切和整体塑性变形的混合型。层间距只影响外层板吸收的能量,随着层间距的变化,双层平板吸收能量没有一定规律。厚度分配比小于1时,双层板的抗冲击性能随着厚度分配比的减小而增强;厚度分配比大于1时,双层板的抗冲击性能随着厚度分配比的增大而增强。     

进气条件对压气机中介机匣流场影响的试验研究

以某压气机中介机匣为试验研究对象,通过改变来流径向分布与马赫数,建立了评估中介机匣气动性能的进口约束条件。在同步测量轴向流路离散压力参数的基础上,分析了中介机匣内部流场对进气条件的稳态响应。研究结果表明:进气条件对中介机匣流动损失影响较大,与均匀进气相比,进气畸变会增大弯曲流道内部径向压力梯度,影响流道曲率与流向压力梯度对附面层的控制效果;支板尾流对通道主流的干扰导致下游平直流道上部区域流场恶化,而进气畸变会加剧支板尾迹的影响;随着进口马赫数的增大,中介机匣总压损失系数与总压畸变强度呈现出不同的增长趋势,其出口流场径向分布对马赫数变化的气动敏感性较高。     

引气对跨声轴流压气机性能的影响

以单级跨声轴流压气机NASA Stage35为研究对象,根据影响转子和静子通道流动的主要物理现象分别设计了多种引气方案.通过数值模拟比较分析引气与不引气状态下压气机的详细流场,结合实验测量结果,研究转子机匣端壁引气位置以及静子机匣端壁引气量对压气机性能及流场的影响.结果表明:转子机匣端壁引气能够有效控制间隙泄漏流的发展,减小叶尖损失,提升压气机性能.不同的引气槽结构和轴向位置对间隙流动的影响机理不相同;静子机匣端壁引气能够有效减小静子叶排损失,提升压气机效率.     

缝式处理机匣轴向位置对压气机特性影响的机理

对轴向倾斜缝处理机匣轴向位置的改变如何影响轴流压气机性能进行了研究.试验与数值结果均表明三个轴向位置的处理机匣均扩宽压气机的稳定工作范围,轴向位置不变时扩稳效果最好,轴向位置后移时效果最差.同时轴向位置前移或后移使压气机等熵效率损害程度降低.通过详细地分析压气机内部流场表明:处理机匣轴向位置后移使叶顶机匣约1/3的轴向...     

Plastic wrinkling prediction in thin-walled part forming process:A review

The precision forming of thin-walled components has been urgently needed in aviation and aerospace field. However, the wrinkling induced by the compressive instability is one of the major defects in thin-walled part forming. The initiation and growth of the wrinkles are interac-tively affected by many factors such as stress states, mechanical properties of the material, geometry of the workpiece and boundary conditions. Especially when the forming process involves compli-cated boundary conditions such as multi-dies constrains, the perturbation of clearances between workpiece and dies and the contact conditions changing in time and space, etc., the predication of the wrinkling is further complicated. In this paper, the current prediction methods were summa-rized including the static equilibrium method, the energy method, the initial imperfection method, the eigenvalue buckling analysis method, the static-implicit finite element method and the dynamic-explicit finite element method. Then, a systematical comparison and summary of these methods in terms of their advantages and limitations are presented. By using a combination of explicit FE method, initial imperfection and energy conservation, a hybrid method is recommended to predict plastic wrinkling in thin-walled part forming. Finally, considering the urgent requirements of com-plex thin-walled structures’ part in aviation and aerospace field, the trends and challenges in wrin-kling prediction under complicated boundary conditions are presented.     

Flow Stability Model for Fan/Compressors with Annular Duct and Novel Casing Treatment

A three-dimensional compressible flow stability model is presented in this paper, which focuses on stall inception of multi-stage axial flow compressors with a finite large radius annular duct configuration for the first time. It is shown that under some assumptions, the stability equation can be obtained yielding from a group of homogeneous equations. The stability can be judged by the non-dimensional imaginary part of the resultant complex frequency eigenvalue. Further more, based on the analysis of the unsteady phenomenon caused by casing treatment, the function of casing treatment has been modeled by a wall impedance condition which is included in the stability model through the eigenvalues and the corresponding eigenfunctions of the system. Finally, some experimental investigation and two numerical evaluation cases are conducted to validate this model and emphasis is placed on numerically studying the sensitivity of the setup of different boundary conditions on the stall inception of axial flow fan/compressors. A novel casing treatment which consists of a backchamber and a perforated plate is suggested, and it is noted that the open area ratio of the casing treatment is less than 10%, and is far smaller than conventional casing treatment with open area ratio of over 50%, which could result in stall margin improvement without obvious efficiency loss of fan/compressors.     

加力燃油泵隔舌倒圆抑制分离的数值模拟

采用动态亚格子应力模型对加力燃油泵内非定常流场进行大涡模拟,探讨了原隔舌空蚀机理,并研究了不同倒圆半径下泵隔舌附近的瞬时流动规律及流量扬程特性.计算结果表明：小流量工况原隔舌处分离产生的强剪切涡会诱发空化,涡脱落形成的分离再附位置与空蚀破坏核心区域相符;小流量工况下,隔舌倒圆在扩散管内形成转向涡,消除了隔舌壁面分离绕流及附着剪切涡,4mm倒圆半径可以避免空化;设计流量范围内隔舌倒圆提高了泵出口扬程,流量越小扬程增幅越大,小流量工况时扬程增幅达3%.