A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

高背压等离子点火器及其液体燃料点火特性实验研究

航天应用的液体火箭发动机及燃烧型加热器燃烧室室压高、燃料流量大、温度低、有重复启动需求，实现安全可靠点火的难度较大。针对这些需求，研究了一种采用高背压设计的电弧等离子体点火器。实验研究了Ar，N₂气体工质在高进气压力下的伏安特性，发现N₂在宽压力范围内适用于点火。发射光谱分析表明，在高达数MPa的进气压力下，Ar，N₂等离子体射流电子密度符合局部热力学平衡判据（LTE判据），点火能量集中。N₂等离子体整体温度低于Ar，但阳极喷口附近温度高于Ar，N₂等离子体射流火焰长，卷吸沿程空气造成射流平均温度偏低，但有助于低温液体推进剂的蒸发混合和强化点火。等离子体射流引起了臭氧和氮氧化物的形成，具有促进点火和化学反应的作用。背压提高引起电源输出电压升高，提高供气压力和电流，有助于点火器在高背压环境中稳定电压。燃烧型空气加热器燃烧室的点火实验发现，采用N₂等离子体喷注面中心点火，可以在短时间内完成酒精-空气和酒精-液氧-空气的点火，最高燃烧室室压接近5MPa时，点火器仍能稳定工作，多次使用电极烧蚀不明显，在液体火箭发动机的重复可靠点火方面具有很好的应用前景。     

火星表面热环境对航天器热控影响分析

火星大气对太阳辐射产生吸收和散射作用，同时还将与火星表面航天器发生对流换热。热设计时难以直接评估对流、辐射和导热三种换热对航天器的影响，从而确定主要的控温途径。在调研火星表面辐射、大气等热环境的基础上，从线性化传热系数和对流辐射比的角度对比分析了辐射、对流和导热对航天器的影响。器表辐射传热系数随光学属性和温度的变化范围为0.3～1.4W/(m2·℃)，对流传热系数随风速变化为0.2～1.5W/(m2·℃)，器内导热传热系数可控制在0.25W/(m2·℃)以下。结果表明，太阳辐射较火星表面和天空辐射而言是主要外热源，航天器表面的辐射和对流换热为两条并联换热途径，两者均可成为主要换热途径，器内导热传热是控制航天器内外隔热的主要可控因素。     

Solar sailing in realistic mode,based on a locally-optimal control laws

Ballistic design of solar sailing missions in the solar system is composed of defining the design parameters, the control programs, and the trajectories that provide performance goals of a flight. The use of a solar sail spacecraft imposes specific restrictions on mission parameters that include the degradation limit on the flight duration, the maximum temperature of solar sail's surface, the minimum distance from the Sun, the maximum angular velocity of the spacecraft's rotation and others.Many authors considered the impact of these restrictions on the design of the mission separately, but they used a sophisticated method of finding the exact optimal motion control or applied the most straightforward laws of motion control. This paper uses local-optimal control laws at the complete mathematical models of motion and functioning of solar sail spacecraft to describe a technique of designing interplanetary missions. The described method avoids the need to obtain an accurate optimal solution to the control problem and does not cause significant computational difficulties.     

航天器运输包装箱仿真验证平台技术研究

针对数量有限的物理跑车试验无法满足减振与保温性能测试需求的问题，提出一套航天器运输包装箱动力学与热学仿真验证方法，包括：建立适用于包装箱系统的刚柔耦合多体动力学系统，通过结合线路条件测试生成的动力学系统外部激励，实现减振性能虚拟跑车测试；建立基于计算流体力学的包装箱热学模型，通过模拟自然对流和空调控制，实现包装箱保温性能虚拟跑车测试；基于C/S架构和导航式流程设计思想，建立航天器运输包装箱仿真验证平台，通过实际案例证明该平台仿真结果与实际跑车测试数据具有较高的一致性。     

涡轮基组合循环发动机分布式控制系统通信网络混合拓扑结构优化方法

涡轮机组合循环(Turbine based combined cycle,TBCC)发动机控制系统通信网络拓扑结构是其分布式控制系统方案设计的重要部分,优化网络拓扑结构可提高发动机推重比和控制系统可靠性。本文基于智能优化算法提出TBCC分布式控制系统网络拓扑结构优化方法。基于图论建立TBCC几何模型和网格模型,以重量和可靠性为优化性能指标,同时考虑发动机表面高温区域以及控制节点的工作可靠性,分别采用粒子群算法和遗传算法优化星形结构中智能中央节点位置、中央节点的环形拓扑结构,获得星形-环形混合拓扑结构。仿真实例表明,基于本文方法优化所得的混合拓扑结构相较于星形集中式控制结构,系统重量降低了51.9%。     

多臂空间机器人的视觉伺服与协调控制

针对多臂空间机器人自主目标抓捕任务，首先建立多臂空间机器人的运动模型和其与目标的相对运动模型，采用Kane方法建立多臂空间机器人的动力学模型；其次，研究基于视觉伺服的机械臂在线轨迹规划算法，并引入零反作用机动，消除机械臂运动对平台姿态的扰动；再次，在不使用零反作用机动功能时，分别使用基于角动量前馈补偿的协调控制算法和逆动力学方法设计了协调控制器，在机械臂运动时保持平台姿态和相对目标的位置。最后，开发了基于Matlab的仿真软件MASS（多臂空间机器人仿真），仿真结果校验了上述方法的有效性。     

Evaluation of SARAL/AltiKa performance using GNSS/IMU equipped buoy in Sajafi,Imam Hassan and Kangan Ports

Performance of SARAL/AltiKa mission has been evaluated within 2016 altimeter calibration/validation framework in Persian Gulf through three campaigns conducted in the offshore waters of Sajafi, Imam Hassan and Kangan Ports, while the altimeter overflew the passes 470, 111 and 25 on 13 Feb, 7 March and 17 June 2016, respectively. As the preparation, a lightweight buoy was equipped with a GNSS receiver/choke-ring antenna and a MEMS-based IMU to measure independent datasets in the field operations. To obtain accurate sea surface height (SSH) time series, the offset of the onboard antenna from the equilibrium sea level was predetermined through surveying operations as the buoy was deploying in the onshore waters of Kangan Port. Accordingly, the double-difference carrier phase observations have been processed via the Bernese GPS Software v. 5.0 so as to provide the GNSS-derived time series at the comparison points of the calibration campaigns, once the disturbing effects due to the platform tilt and heave have been eliminated. Owing to comparing of the SSH time series and the associating altimetry 1?Hz GDR-T datasets, the calibration/validation of the SARAL/AltiKa has been performed in the both cases of radiometer and ECMWF wet troposphere corrections so as to identify potential land contamination. An agreement of the present findings in comparison with those attained in other international calibrations sites confirms the promising feasibility of Persian Gulf as a new dedicated site for calibration/validation of ongoing and future altimetry missions.     

轨控大干扰下的系统角动量管理

摘要： 针对利用角动量交换装置系统实现轨控期间姿态维持的情况，研究当轨控推力器存在大力矩扰动时系统角动量管理方法.结合对地运行航天器轨道运动特性，分析轨控干扰力矩的积累角动量变化规律；考虑角动量管理装置系统的角动量存贮容量，基于角动量积累规律提出了一种结合偏置角动量建立与对称分布轨控位置选择的系统角动量管理方法，实现了对称轨控位置积累角动量互相抵消的自平衡效果，极大程度地提高轨控效率且避免系统角动量饱和现象.所提出的方法适用于喷气欠驱动控制系统，方法的有效性通过了数学仿真验证及在轨型号应用.     

Assessment of between-floor structural and topological properties on cognitive map development in multilevel built environments

The present study investigated cognitive map development in multilevel built environments. Three experiments were conducted in complex virtual buildings to examine the effects of five between-floor structural factors that may impede the accuracy of humans’ ability to build multilevel cognitive maps. Results from Experiments 1 and 2 (of three experiments) revealed that difficulties in developing multilevel cognitive maps are not solely caused by the z-axis offset, as is suggested in the literature, but are due to the factorial combination of a between-floor overlap and a z-axis offset. Results from Experiment 2 showed that this process becomes substantially more difficult when the reference directions between different floors have an angular offset from each other. Finally, results from Experiment 3 demonstrated that confusing between-floor heading shifts in aligned buildings did not make it reliably harder to build multilevel cognitive maps. The implications of these findings are discussed in terms of theories of mental representations in multilayered three-dimensional spaces, as well as for architectural design.