Implementation of tactical maneuvers with maneuver libraries

This study creates and combines the general maneuver libraries for fixed-wing aircraft to implement tactical maneuvers. First, the generalized maneuver libraries are established by analyzing the characteristics of tactical maneuvers required in battlefields. The 7th order polynomial is applied to both the creation of the maneuver libraries and the generation of the trajectories or flight paths for modal inputs. To track the desired trajectory, we design the Attitude Command Attitude Hold (ACAH) system and the Rate Command Rate Hold (RCRH) system using Model Following Controller (MFC). Moreover, the Line-of-Sight (LOS) guidance law is designed. In particular, the CONDUIT® is employed to optimize the gains so that the control systems meet the aircraft Handling Qualities (HQ) criteria. Finally, flight simulations are performed for the longitudinal loop, immelmann-turn, and climb-slalom-descent maneuvers to verify that tactical aggressive maneuvers are realizable via the combination of maneuver libraries. This study can contribute to the development of flight techniques for aircraft tactical maneuvers and to the revision of air force operational manuals.     

钛合金表面抗激光涂层损伤特性及热效应影响研究

实验研究了钛合金和高反射型陶瓷涂层材料抗连续型激光烧蚀的损伤及温度分布特性，并从热效应影响角度对比分析了二者在抗激光损伤效果方面的差异性。研究结果表明：相比于钛合金，高反射型陶瓷涂层材料能有效增强钛合金基底抗激光损伤的能力；在同等激光功率密度辐照下，陶瓷涂层材料能有效提升钛合金基底耐受激光辐照的时间长度。实验结果表明该陶瓷涂层材料的激光损伤阈值比钛合金高约5.8倍。实验发现陶瓷涂层温升速率高于钛合金，但由于陶瓷材料具有较高的反射特性，以及良好的热吸收和热传导特性，因此能使由激光辐照产生的热量在其表面较快地扩散，而降低向基底方向传导的程度，最终提升陶瓷涂层的抗激光损伤阈值。     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

基于HHT的航空直流串行电弧特征提取方法

由于飞机内部布线空间有限、电弧故障存在发生时间地点随机以及特征不明显等问题，导致检测困难。本文基于航空270 V高压直流（HVDC）系统开展直流串行电弧故障特征提取方法研究，采用希尔伯特黄变换（HHT）提取电弧电流交流分量的时域和频域特征量。选择HHT的固有模态函数IMF5瞬时幅值的峰峰值和标准差作为识别电弧故障的时域特征，与原始信号中提取的时域特征量对比，正常和电弧特征量的区分度更大；选择HHT的固有模态函数IMF1+IMF2、一定频带范围内的瞬时幅值计算得到的谐波功率和作为区分正常和电弧情况的频域特征量。与常用的快速傅里叶变换（FFT）方法相比，HHT三维时频谱能够反映信号的局部特征，HHT方法计算得到的正常和电弧特征量之间的区分度更大，电弧和正常特征量的比值最高可达346。基于HHT的电弧故障特征提取方法能够更好地区分正常和电弧情况，有助于提高电弧故障的检测率，降低虚警率，具有重要的工程应用价值。     

Simulation and analysis of chemical release in the ionosphere

Ionospheric inhomogeneous plasma produced by single point chemical release has simple space-time structure, and cannot impact radio wave frequencies higher than Very High Frequency (VHF) band. In order to produce more complicated ionospheric plasma perturbation structure and trigger instabilities phenomena, multiple-point chemical release scheme is presented in this paper. The effects of chemical release on low latitude ionospheric plasma are estimated by linear instability growth rate theory that high growth rate represents high irregularities, ionospheric scintillation occurrence probability and high scintillation intension in scintillation duration. The amplitude scintillations and the phase scintillations of 150?MHz, 400?MHz, and 1000?MHz are calculated based on the theory of multiple phase screen (MPS), when they propagate through the disturbed area.     

小型磁偏转质谱计性能实验研究

自主研发了小型磁偏转质谱计，并对其质量范围、分辨本领、灵敏度和最小可检分压力四个主要性能指标进行了实验测试和比对。结果表明，该质谱计的质量范围为（1~143）amu，相对N₂的分辨本领为1400，灵敏度为4.2×10^-5 A/Pa，最小可检分压力为9.5×10^-7 Pa。该测试和比对结果为磁偏转质谱计进一步的优化设计和性能提高奠定了重要基础。     

纳米碳粉掺杂对激光烧蚀GAP的推进性能影响

实验以含能聚合物聚叠氮缩水甘油醚(Glycidyl azide polymer,GAP）作为激光烧蚀微推力器的靶材。通过对不同浓度纳米碳粉掺杂和靶材厚度下激光烧蚀GAP的比冲、冲量耦合系数和能量转化效率测量，结合靶材喷射羽流图像，分析了纳米碳粉掺杂提高激光烧蚀聚合物靶材推进性能的机理，给出纳米碳粉掺杂的适用方式。实验结果表明：透射式下，掺杂纳米碳粉之后，聚合物对激光的吸收大幅增强，但激光烧蚀推进性能不随掺杂浓度增加而显著提升；纳米碳粉吸收激光能量形成温度极高的局部热区促进聚合物中化学能的释放，是推进性能提升的主要原因；掺杂纳米碳粉之后的GAP烧蚀深度降低，表现出面吸收特性；随着靶材厚度的增加，未完全烧蚀的工质质量增加，使得靶材的利用率大大降低，导致聚合物推进性能下降。实验中掺杂3%纳米碳粉、厚度为54 μm的GAP靶材最优能量转化效率超过250%，适合作为透射式激光烧蚀微推力器的靶材。     

光敏推进剂激光烧蚀过程建模与仿真

相较于传统大卫星,微小卫星具有结构紧凑、质量轻便和成本低廉的特点。然而,受功率和质量负载的限制,微小卫星一般不装备推进系统,其航线也局限于近地轨道。为扩展微小卫星的功能,满足日益复杂的任务需求,需给其配备合适的微推进系统。固体推进系统具有结构简单、寿命长、可靠性高的优点,但无法重复启动。为得到可重复启动的固体微推进系统,设计了一种非自持燃烧的光敏推进剂,采用激光控制其燃烧。在背压为大气压的环境下,利用高速摄像机拍摄燃烧过程并记录燃速。之后,对光敏推进剂的激光烧蚀过程进行建模。分析结果表明:激光可控制光敏推进剂的燃烧,燃速与激光强度成线性关系;该光敏推进剂的最小激光点火强度为0.28 W/mm~2;燃速计算值与实测值的误差在10%以内,证明该数学模型具备工程应用价值。     

Investigating the Coronal Mass Ejections associated with DH type-II radio bursts and solar flares during the ascending phase of the solar cycle 24

We studied a set of 74 CMEs, with shedding the light on the halo-CMEs (HCMEs), that are associated with decametric – hectometric (DH) type-II radio bursts (1–16?MHz) and solar flares during the period 2008–2014. The events were classified into 3 groups (disk, intermediate, and limb events) based on their longitudinal distribution.We found that the events are mostly distributed around 15.32° and 15.97° at the northern and southern solar hemispheres, respectively. We found that there is a clear dependence between the longitude and the CME’s width, speed, acceleration, mass, and kinetic energy. For the CMEs’ widths, most of the events were HCMEs (～62%), while the partial HCMEs comprised ～35% and the rest of events were CMEs with widths less than 120°. For the CMEs’ speeds, masses, and kinetic energies, the mean values showed a direct proportionality with the longitude, in which the limb events had the highest speeds, the largest masses, and the highest kinetic energies. The mean peak flux of the solar flares for different longitudes was comparable, but the disk flares were more energetic. The intermediate flares were considered as gradual flares since they tended to last longer, while the limb flares were considered as impulsive flares since they tended to last shorter.A weak correlation (R?=?0.32) between the kinetic energy of the CMEs and the duration of the associated flares has been noticed, while there was a good correlation (R?=?0.76) between the kinetic energy of the CMEs and the peak flux of the associated flares. We found a fair correlation (R?=?0.58) between the kinetic energy of the CMEs and the duration of the associated DH type-II radio bursts.     

低温磨料气射流加工PDMS实验研究

通过自研的低温磨料气射流加工装置进行低温磨料气射流加工聚二甲基硅氧烷(polydimethylsiloxane,PDMS)实验研究,分析了加工时间、加工距离、冲蚀角度和磨料粒径对冲蚀率、孔深和孔横截面形貌的影响。结果表明:随着加工时间的增加,冲蚀率先增大后减小,在第1阶段加工过程中,孔深与加工时间大致呈线性关系,增加加工时间还可使孔底部变平整;存在一个最佳加工距离使孔深最大,当加工距离大于最大加工距离时,孔深将随着加工距离的增加而急剧下降,孔的锥度随着加工距离的增大而增大;当冲蚀角度处于30°～60°之间时,冲蚀率最大,随着冲蚀角度的增加,孔的形状逐步由椭圆形变成圆形;存在一个最佳磨料粒径,使冲蚀率和孔深达到最大;当冲蚀角度小于90°时,低温磨料气射流加工PDMS材料去除机理为塑性去除和脆性去除的结合。