全文获取类型
收费全文 | 257篇 |
免费 | 111篇 |
国内免费 | 41篇 |
专业分类
航空 | 229篇 |
航天技术 | 81篇 |
综合类 | 11篇 |
航天 | 88篇 |
出版年
2023年 | 13篇 |
2022年 | 9篇 |
2021年 | 18篇 |
2020年 | 14篇 |
2019年 | 16篇 |
2018年 | 21篇 |
2017年 | 32篇 |
2016年 | 10篇 |
2015年 | 19篇 |
2014年 | 19篇 |
2013年 | 12篇 |
2012年 | 24篇 |
2011年 | 23篇 |
2010年 | 24篇 |
2009年 | 26篇 |
2008年 | 15篇 |
2007年 | 25篇 |
2006年 | 14篇 |
2005年 | 14篇 |
2004年 | 9篇 |
2003年 | 9篇 |
2002年 | 7篇 |
2001年 | 10篇 |
2000年 | 7篇 |
1999年 | 2篇 |
1998年 | 6篇 |
1997年 | 1篇 |
1996年 | 1篇 |
1993年 | 2篇 |
1992年 | 1篇 |
1991年 | 2篇 |
1990年 | 2篇 |
1989年 | 1篇 |
1988年 | 1篇 |
排序方式: 共有409条查询结果,搜索用时 15 毫秒
1.
针对微型惯性开关闭合时间短、接触弹跳问题,设计了增强接触效果的摩擦接触式微型惯性开关。基于MEMS惯性开关工作原理,建立了开关物理模型,研究了不同类型惯性开关的闭合性能,提出了增强接触的摩擦接触方法,设计了摩擦接触式微型惯性开关的结构。为了对比接触性能,基于UV–LIGA叠层光刻和精密微电铸工艺,研制了3种不同类型的惯性开关。最后,进行落锤试验,测试结果显示:施加400g外载加速度时,刚性、柔性、摩擦接触式微型惯性开关的闭合时间分别为10μs、80μs、620μs;在惯性开关中引入摩擦电极,既能延长闭合时间,又能解决弹跳问题。研究结果表明,摩擦接触式微型惯性开关在增强接触效果方面具有很大的优越性。 相似文献
2.
半球谐振子的寿命和损伤是直接影响高精度半球谐振陀螺使用时长和安全性的重要因素。目前国内加工的半球谐振子所用的熔融石英玻璃材料主要依靠进口,采用传统的疲劳寿命实验确定方法成本过于昂贵,因此需要利用疲劳分析软件对半球谐振子的疲劳寿命进行分析。文章通过半球谐振陀螺应力分析,采用ANSYS软件对熔融石英半球谐振子进行应力分析仿真,确定因残余应力所引起的疲劳危险部位,并在疲劳部位进行裂纹扩展分析,得到 、 和 型应力强度因子,以使在半球谐振子结构设计和使用过程中对易疲劳的部位进行有效监控和预防。 相似文献
3.
4.
5.
激光陀螺的高频机抖使得激光陀螺惯性测量单元(IMU)的测量数据包含较大的随机噪声。传统标定方法通过延长测量时间消除对随机噪声的影响,降低了标定效率。提出了应用自适应前向线性预测(FLP)滤波对激光陀螺IMU的标定数据进行降噪,在较小标定数据量情况下提高系统的标定精度。首先通过四方位正反速率标定试验获得原始标定数据;然后通过自适应FLP滤波器对标定数据进行噪声抑制;最后利用降噪后的数据计算标定参数。试验结果表明,该方法能够有效抑制标定数据中的随机噪声,提高信号的信噪比(SNR),从而在标定数据量较小的情况下得到较高精度的标定参数,提升系统的导航精度。 相似文献
7.
8.
转子-滚动轴承试验器有限元建模及实验验证 总被引:1,自引:0,他引:1
针对自行研制的转子-滚动轴承试验器,在Pro/E中建立了单盘转子的三维实体模型。通过Pro/E与ANSYS的无缝连接技术,在ANSYS中得到单盘转子的三维有限元模型,采用Sol-id185实体单元进行网格划分并采用Subspace法得到了前4阶固有频率和振型。利用锤击法对转子试验器进行了实验模态分析,并与ANSYS模态分析结果进行了对比。结果表明,基于ANSYS的计算模态和实验模态达到了很好的一致性。同时,利用ANSYS分析了陀螺力矩对临界转速的影响。最后,利用修改后的有限元模型仿真计算了不平衡动力响应,与相同条件下的实验结果比较表明,所建立的有限元模型能够准确模拟实际转子-滚动轴承试验器的动力学行为。 相似文献
9.
10.
Vaios Lappas Nasir Adeli Lourens Visagie Juan Fernandez Theodoros Theodorou Willem Steyn Matthew Perren 《Advances in Space Research (includes Cospar's Information Bulletin, Space Research Today)》2011
CubeSail is a nano-solar sail mission based on the 3U CubeSat standard, which is currently being designed and built at the Surrey Space Centre, University of Surrey. CubeSail will have a total mass of around 3 kg and will deploy a 5 × 5 m sail in low Earth orbit. The primary aim of the mission is to demonstrate the concept of solar sailing and end-of-life de-orbiting using the sail membrane as a drag-sail. The spacecraft will have a compact 3-axis stabilised attitude control system, which uses three magnetic torquers aligned with the spacecraft principle axis as well as a novel two-dimensional translation stage separating the spacecraft bus from the sail. CubeSail’s deployment mechanism consists of four novel booms and four-quadrant sail membranes. The proposed booms are made from tape-spring blades and will deploy the sail membrane from a 2U CubeSat standard structure. This paper presents a systems level overview of the CubeSat mission, focusing on the mission orbit and de-orbiting, in addition to the deployment, attitude control and the satellite bus. 相似文献