首页 | 本学科首页   官方微博 | 高级检索  
文章检索
  按 检索   检索词:      
出版年份:   被引次数:   他引次数: 提示:输入*表示无穷大
  收费全文   2360篇
  免费   885篇
  国内免费   415篇
航空   2258篇
航天技术   518篇
综合类   244篇
航天   640篇
  2024年   2篇
  2023年   69篇
  2022年   113篇
  2021年   145篇
  2020年   132篇
  2019年   119篇
  2018年   108篇
  2017年   155篇
  2016年   160篇
  2015年   141篇
  2014年   179篇
  2013年   127篇
  2012年   198篇
  2011年   205篇
  2010年   153篇
  2009年   174篇
  2008年   152篇
  2007年   183篇
  2006年   174篇
  2005年   108篇
  2004年   88篇
  2003年   109篇
  2002年   84篇
  2001年   73篇
  2000年   70篇
  1999年   70篇
  1998年   75篇
  1997年   61篇
  1996年   45篇
  1995年   50篇
  1994年   51篇
  1993年   23篇
  1992年   19篇
  1991年   15篇
  1990年   11篇
  1989年   11篇
  1988年   6篇
  1987年   1篇
  1984年   1篇
排序方式: 共有3660条查询结果,搜索用时 23 毫秒
1.
为优化高温升主燃烧室燃烧性能,对三级旋流主燃烧室开展雾化特性试验研究。预燃级喷嘴采用离心喷嘴压力雾化和气动雾化相结合,主燃级采用预膜式气动雾化。试验采用相位多普勒粒子分析仪对主预燃级喷嘴和燃油分级后的雾化特性进行研究,对比分析了不同头部压降和燃油流量在不同轴向截面和径向位置的液滴粒径分布,并利用高速摄像对不同工况下的喷雾形态进行了记录。试验结果表明:主燃级油雾粒径为50~80μm,气液比达到3.5即可达到良好的雾化水平。随着轴向距离延长,喷雾粒径变大,喷雾浓度变得均匀。燃油分级比增加可降低整体粒径约10μm,且主要影响中心区域,对雾锥外侧粒径影响不大。  相似文献   
2.
燃油离心泵多目标优化设计及仿真分析   总被引:1,自引:1,他引:0       下载免费PDF全文
李嘉  李华聪  王万成  王玥 《推进技术》2021,42(3):666-674
针对燃油离心泵高效、高抗汽蚀优化设计问题,进行了基于损失模型和SQP算法下的多目标优化设计并进行了仿真应用。首先,考虑叶轮、蜗壳等通流部件内的水利损失、容积损失以及机械损失,建立表征离心泵效率的综合损失模型;结合基于必须汽蚀余量计算下的汽蚀表征函数以确定离心泵多目标函数。进而,利用SQP算法构造合理的适应度函数,结合约束条件确定离心泵多目标优化设计的数学模型。其次,对某型燃油离心泵进行基于SQP算法的优化设计并与其他常用优化算法进行对比。可以看到:各优化算法的最优结果几乎相似,但SQP算法对多维非线性方程组优化求解所用的迭代步数相对较少。最后,利用CFD技术进行仿真及外特性预测,以验证基于SQP算法下燃油离心泵多目标优化设计的有效性。结果表明:相比传统方法设计的原型离心泵,基于SQP算法优化的离心泵内流场压力分布相对均匀,流动损失更低,且进口流动有利于抗汽蚀性能;从外特性结果来看,基于SQP算法优化的离心泵高效工作区域相对宽广,必须汽蚀余量相对较低,抗汽蚀性能有所改善。  相似文献   
3.
某型惯性导航系统在飞机上时有故障发生,造成导航系统无法正常使用,其中较为突出的是惯导报53#环境温控故障。为降低该惯导在飞机上的故障率,通过研究环境温控回路的工作原理,解析其故障机理,并以几起典型53#故障的排除为例深入分析,提出有效的预防措施,以延伸修理深度,提高产品修理质量。  相似文献   
4.
In recent years, land surface temperature (LST) has become critical in environmental studies and earth science. Remote sensing technology enables spatiotemporal monitoring of this parameter on large scales. This parameter can be estimated by satellite images with at least one thermal band. Sentinel-3 SLSTR data provide LST products with a spatial resolution of 1 km. In this research, direct and indirect validation procedures were employed to evaluate the Sentinel-3 SLSTR LST products over the study area in different seasons from 2018 to 2019. The validation method was based on the absolute (direct) evaluation of this product with field data and comparison (indirect) evaluation with the MODIS LST product and the estimated LST using the non-linear split-window (NSW) algorithm. Also, two emissivity estimation methods, (1) NDVI thresholding method (NDVI-THM) and (2) classification-based emissivity method (CBEM), were used to estimate the LST using the NSW method according to the two thermal bands of Sentinel-3 images. Then, the accuracy of these methods in estimating LST was evaluated using field data and temporal changes of vegetation, which the NDVI-THM method generated better results. For indirect evaluation between the Sentinel-3 LST product, MODIS LST product, and LST estimated using NSW, four filters based on spatial and temporal separates between pairs of pixels and pixel quality were used to ensure the accuracy and consistency of the compared pairs of a pixel. In general, the accuracy results of the LST products of MODIS and Sentinel-3, and LST estimated using NSW showed a similar trend for LST changes during the seasons. With respect to the two absolute and comparative validations for the Sentinel-3 LST products, summer with the highest values of bias (?1.24 K), standard deviation (StDv = 2.66 K), and RMSE (2.43 K), and winter with the lowest ones (bias of 0.14 K, StDv of 1.13 K, and RMSE of 1.12 K) provided the worst and best results for the seasons in the period of 2018–2019, respectively. According to both absolute and comparative evaluation results, the Sentinel-3 SLSTR LST products provided reliable results for all seasons on a large temporal and spatial scale over our studied area.  相似文献   
5.
刘昌国  关亮  施伟  王子模 《推进技术》2021,42(7):1662-1670
为探究低温环境下单组元300N发动机的工作特性,揭示影响发动机低温性能的主要影响因素,以300N发动机为试验对象,开展了模拟飞行工况的发动机低温试验。给出了低温试验研究方法,分别从温度差异对发动机性能影响、催化剂活性差异对发动机低温启动特性影响和低温对电磁阀响应特性影响等方面获得研究结果。结果表明,低温是影响发动机低温性能的主要影响因素,-48℃条件催化剂无法完成推进剂的催化分解,发动机发生爆炸;-30℃条件下起活时间为80.5~87.5ms,发动机可正常启动,且启动温度与起活时间呈指数关系;催化剂批次差异也对发动机低温工作性能产生一定影响,不同批次催化剂低温起活时间的差异可达91ms;低温试验过程中,电磁阀的关闭受到低温推进剂粘性和背压的影响,产生了明显的迟滞现象,延迟时间约100ms,对发动机在轨的精准控制存在一定影响。  相似文献   
6.
在定向炉中分别采用籽晶法制备了[001]、[011]和[111]3种不同取向的第四代单晶高温合金DD15,在800℃研究了不同取向的高周疲劳性能,分析了合金不同取向的显微组织、疲劳断口形貌和疲劳断裂组织。结果表明:在凝固方向横截面上不同取向合金的铸态枝晶和热处理γ′相组织明显不同。合金800℃的高周疲劳性能存在各向异性,疲劳极限按[111]、[001]、[011]取向的顺序降低。不同取向合金的高周疲劳都是沿平面断裂,断裂平面与试样中心应力轴线的角度不同,角度按[011]、[001]、[111]取向的顺序逐渐减小。不同取向高周疲劳断口特征基本相同,可见疲劳源区、疲劳扩展区和瞬断区。疲劳裂纹起源于试样表面或亚表面并沿{111}平面扩展。扩展区上可见河流状花样和疲劳条带。瞬断区可见撕裂棱和解理台阶特征,其断裂机制都为类解理断裂。由于试验温度较低,不同取向疲劳断裂后的γ′相仍保持立方形状。  相似文献   
7.
以982℃固溶水冷状态的Inconel 718合金棒材为研究对象,分析该合金经重复固溶再时效处理后的组织性能,并与直接时效处理进行对比。结果表明:在941~1010℃范围内重复固溶,随着固溶温度的升高,晶粒无明显变化,但是δ相含量逐渐减少,主要强化相γ′′的析出量增多,使合金硬度、高温拉伸强度和高温持久寿命显著提高,高温拉伸塑性、高温持久塑性在982℃固溶时达到极大值。与直接进行时效处理相比,经982℃重复固溶再时效处理后的组织性能无明显变化,更低的重复固溶温度对性能不利,而更高的重复固溶温度则使性能提高。  相似文献   
8.
采用电化学阳极氧化技术在含NH4F的乙二醇电解液中对TiAl合金进行阳极氧化处理。研究阳极氧化对TiAl合金高温氧化行为和力学性能的影响。结果表明:由于“卤素效应”,阳极氧化处理的TiAl合金经高温氧化后表面形成致密、连续的Al2O3氧化膜,有效阻止了氧的内扩散,进而显著提高合金的抗高温氧化性能。经1000℃氧化100 h后,阳极氧化试样增重由未经阳极氧化处理试样的85.86 mg/cm2降至0.67 mg/cm2。另一方面,阳极氧化TiAl合金表面硬度和弹性模量随高温氧化时间延长呈先降低后升高的趋势。阳极氧化TiAl合金在高温服役后,合金的摩擦系数较未经阳极氧化处理试样上升,但表面耐磨性先降低后升高。这是由于TiAl合金经阳极氧化后,表面形成了一层富铝含氟氧化膜,由于氧化膜中F元素在高温氧化过程中与Ti、Al结合形成卤化物,卤化物蒸气选择性扩散在原始氧化膜处形成致密的Al2O3保护膜。阳极氧化对TiAl合金力学性能的影响主要是由于氧化膜中Al2O3的含量变化所致。  相似文献   
9.
《中国航空学报》2021,34(4):465-475
Severe tool wear and poor surface quality are the main problems during micro machining of cemented carbide. In this work, an innovative hybrid process of laser-induced oxidation assisted micro milling (LOMM) was proposed to solve the problems. A nanosecond laser was utilized to induce oxidation of the WC-20%Co material, producing loose oxide which was easy to remove. The micro machinability of the material was improved by laser-induced oxidation. The oxidation mechanisms of cemented carbide were studied. A microgroove with a depth of 2.5 mm and aspect ratio of 5 was fabricated successfully. The milling force, surface quality and tool wear mechanisms were investigated. For comparison, a microgroove was also fabricated with conventional micro milling (COMM) using identical milling parameters. Results revealed that in LOMM the milling force and tool wear rate were extremely low during removing the oxide. The machined surface quality and dimensional accuracy achieved by LOMM were superior to those obtained by COMM. The surface roughness Sa of the microgroove bottom reached 88 nm in LOMM, while the cross-sectional geometry of the microgroove was a trapezoid. Perpendicularity of the microgroove sidewall machined by LOMM was better than that by COMM. The tool wear forms in LOMM were coating spalling and slight tool nose breakage. Compared with COMM, the tool life in LOMM was prolonged significantly. It indicates that the proposed hybrid process is an effective and efficient way to fabricate high aspect ratio micro-features with high dimensional accuracy.  相似文献   
10.
《中国航空学报》2021,34(9):47-59
The aircraft system has recently gained its reputation as a reliable and efficient tool for sensing and parsing aerial scenes. However, accurate and fast semantic segmentation of high-resolution aerial images for remote sensing applications is still facing three challenges: the requirements for limited processing resources and low-latency operations based on aerial platforms, the balance between high accuracy and real-time efficiency for model performance, and the confusing objects with large intra-class variations and small inter-class differences in high-resolution aerial images. To address these issues, a lightweight and dual-path deep convolutional architecture, namely Aerial Bilateral Segmentation Network (Aerial-BiSeNet), is proposed to perform real-time segmentation on high-resolution aerial images with favorable accuracy. Specifically, inspired by the receptive field concept in human visual systems, Receptive Field Module (RFM) is proposed to encode rich multi-scale contextual information. Based on channel attention mechanism, two novel modules, called Feature Attention Module (FAM) and Channel Attention based Feature Fusion Module (CAFFM) respectively, are proposed to refine and combine features effectively to boost the model performance. Aerial-BiSeNet is evaluated on the Potsdam and Vaihingen datasets, where leading performance is reported compared with other state-of-the-art models, in terms of both accuracy and efficiency.  相似文献   
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号