燃油离心泵多目标优化设计及仿真分析

针对燃油离心泵高效、高抗汽蚀优化设计问题,进行了基于损失模型和SQP算法下的多目标优化设计并进行了仿真应用。首先,考虑叶轮、蜗壳等通流部件内的水利损失、容积损失以及机械损失,建立表征离心泵效率的综合损失模型；结合基于必须汽蚀余量计算下的汽蚀表征函数以确定离心泵多目标函数。进而,利用SQP算法构造合理的适应度函数,结合约束条件确定离心泵多目标优化设计的数学模型。其次,对某型燃油离心泵进行基于SQP算法的优化设计并与其他常用优化算法进行对比。可以看到：各优化算法的最优结果几乎相似,但SQP算法对多维非线性方程组优化求解所用的迭代步数相对较少。最后,利用CFD技术进行仿真及外特性预测,以验证基于SQP算法下燃油离心泵多目标优化设计的有效性。结果表明：相比传统方法设计的原型离心泵,基于SQP算法优化的离心泵内流场压力分布相对均匀,流动损失更低,且进口流动有利于抗汽蚀性能；从外特性结果来看,基于SQP算法优化的离心泵高效工作区域相对宽广,必须汽蚀余量相对较低,抗汽蚀性能有所改善。     

晶体取向对第四代单晶高温合金DD15高周疲劳性能的影响

在定向炉中分别采用籽晶法制备了[001]、[011]和[111]3种不同取向的第四代单晶高温合金DD15,在800℃研究了不同取向的高周疲劳性能,分析了合金不同取向的显微组织、疲劳断口形貌和疲劳断裂组织。结果表明:在凝固方向横截面上不同取向合金的铸态枝晶和热处理γ′相组织明显不同。合金800℃的高周疲劳性能存在各向异性,疲劳极限按[111]、[001]、[011]取向的顺序降低。不同取向合金的高周疲劳都是沿平面断裂,断裂平面与试样中心应力轴线的角度不同,角度按[011]、[001]、[111]取向的顺序逐渐减小。不同取向高周疲劳断口特征基本相同,可见疲劳源区、疲劳扩展区和瞬断区。疲劳裂纹起源于试样表面或亚表面并沿{111}平面扩展。扩展区上可见河流状花样和疲劳条带。瞬断区可见撕裂棱和解理台阶特征,其断裂机制都为类解理断裂。由于试验温度较低,不同取向疲劳断裂后的γ′相仍保持立方形状。     

Time delay compensation in lateral-directional flight control systems at high angles of attack

The previous studies of time delay compensation in flight control systems are all based on the conventional aerodynamic derivative model and conducted in longitudinal motions at low angles of attack. In this investigation, the effects of time delay on the lateral-directional stability augmentation system in high-α regime are discussed based on the $\dot{\beta }$ model, which is proposed in our previous work and proved as a more accurate aerodynamic model to reveal the lateral-directional unsteady aerodynamic characteristics at high angles of attack. Both the $\dot{\beta }$ model and the quasi-steady model are used for simulating the effects of time delay on the flying qualities in high-α maneuvers. The comparison between the simulation results shows that the flying qualities are much more sensitive to the mismatch of feedback gains than the state errors caused by time delay. Then a typical adaptive controller based on the conventional dynamic derivative model and a gain-prediction compensator based on $\dot{\beta }$ model are designed to address the time delay in different maneuvers. The simulation results show that the gain-prediction compensator is much simpler and more efficient at high angles of attack. Finally, the gain-prediction compensator is combined with a linearized $\dot{\beta }$ model reference adaptive controller to compensate the adverse effects of very large time delay, which exhibits excellent performance when addressing the extreme conditions at high angles of attack.     

铝颗粒云燃烧研究进展

为探究铝颗粒云燃烧特性，把握其研究进展，并为后续研究工作提供参考，本文首先简述了铝颗粒点火、燃烧过程，总结了铝颗粒燃烧机理；其次，综述了铝颗粒云燃烧的实验、理论和模拟研究进展，从不同维度分析了影响颗粒云火焰速度的关键参数，并提出颗粒云燃烧的研究方向，包括提升颗粒云燃烧实验颗粒分散均匀性与表征精度、降低火焰传播速度等实验结果散差、改善颗粒云燃烧理论预测模型精度及构建实用的颗粒云燃烧模拟CFD模型。     

基于惯性定位定向的高铁轨检仪研究

根据高铁轨道静态检测的测量需求，设计了一种利用定位定向技术的0级轨检仪，详细阐述了其构成和工作原理，介绍了其特点。通过对比性分析论证，优选了一种测量精度高、操作方法简单且可大幅度提高测量效率的设计方案。理论仿真表明，本系统测量精度能够达到优于13mm/km水平。根据理论仿真结果搭建了原理简易验证设备，结合高铁测控网的测量基准，在一段高铁的弯道铁轨上进行了验证测试。从测试结果看，样机测量精度的重复性可以到达1mm/500m（1σ）的水平，10次测量效率优于500m/2h，表明采用定位定向技术的0级轨检仪具备实际工程化的潜力，以及提高测量效率和精度的能力。     

一种未来大型天地往返运输系统平台气动方案

针对未来低运行成本、可直接水平起降、重复使用的大型天地往返运输系统平台飞行器研制所需重点解决的全速域气动力性能需求与气动热防护匹配等难题，分析了典型航天飞机方案所存在的能量运行缺陷等主要问题及可能的改善方案。基于放宽气动热防护设计、涡轮/冲压/火箭发动机三动力组合、嵌套式旋转机翼全速域变体、在爬升阶段将飞行动能转化为高度势能以及再入阶段“跳跃式”盘旋减速飞行轨迹控制等设计思想，从能量损失速率控制和回收利用等角度出发，开展了一种新型大型天地往返运输系统平台气动布局概念设计研究。全速域气动力/热性能工程估算以及内/外流整体气动效能初步分析结果表明，该方案可有效满足整个飞行包线内的升重平衡需求，相比航天飞机方案具有显著的整体气动效能优势，值得进一步开展深入研究。     

(70~100)MeV准单能中子参考辐射场设计

国内基于串列加速器建立了144keV~15MeV的单能中子参考辐射场，解决了20MeV以下能区中子探测器注量、剂量等参数的量值溯源，但尚未建立20MeV以上能区准单能中子参考辐射场。随着航天空间中子探测任务的需要以及地面高能质子加速器的发展，20MeV以上能区准单能中子参考辐射场需求越来越突出。发展20MeV以上能区高能中子参考辐射场对于满足国防需求、推动中子计量学科发展具有重要意义。     

基于动态补偿的多电机控制算法

多电机协调控制达到转速一致是电机控制中的一个关键难题，外加负载变动和电机参数变化时会引起电机性能的下降，达不到良好的控制效果。为使电机间保持转速同步，建立了永磁同步电机d-q坐标系下的矢量控制数学模型，基于转速跟随控制，提出一种基于单神经元PID的变增益速度补偿器进行偏差耦合控制。在MATLAB/Simulink建立了3台永磁同步电机的仿真模型。仿真结果表明，与传统PID固定增益速度补偿器算法相比，单神经元PID的变增益速度补偿器具有更强的鲁棒性以及更快的收敛性。     

弹载变转速定量泵高动态压力控制特性分析

传统弹载电液伺服系统的液压能源采用有刷直流电机驱动恒压变量泵的方式，泵源压力在导弹飞行过程中设定值恒定，但在平飞段过程长、负载小，对能源压力需求低，造成弹上能源总利用率不高的问题，提出无刷直流电机驱动小排量液压泵的压力控制泵源的设计，在低气动负载阶段适当降低系统压力，进而降低节流损失与泄漏量，提高能量利用率。分析了变转速定量泵的流量压力特性曲线，通过建立基于变转速压力控制泵源的位置电液伺服系统数学模型与仿真模型，分析了变转速定量泵压力控制系统在典型工况下的位置跟踪、系统压力变化与能量利用效率，验证了压力控制系统能够在导弹平飞段保证位置伺服系统跟踪正常的前提下，能有效提高系统效率，证明了变转速定量泵压力控制系统的有效性与可行性。     

Laser-induced oxidation assisted micro milling of high aspect ratio microgroove on WC-Co cemented carbide

Severe tool wear and poor surface quality are the main problems during micro machining of cemented carbide. In this work, an innovative hybrid process of laser-induced oxidation assisted micro milling (LOMM) was proposed to solve the problems. A nanosecond laser was utilized to induce oxidation of the WC-20%Co material, producing loose oxide which was easy to remove. The micro machinability of the material was improved by laser-induced oxidation. The oxidation mechanisms of cemented carbide were studied. A microgroove with a depth of 2.5 mm and aspect ratio of 5 was fabricated successfully. The milling force, surface quality and tool wear mechanisms were investigated. For comparison, a microgroove was also fabricated with conventional micro milling (COMM) using identical milling parameters. Results revealed that in LOMM the milling force and tool wear rate were extremely low during removing the oxide. The machined surface quality and dimensional accuracy achieved by LOMM were superior to those obtained by COMM. The surface roughness S_a of the microgroove bottom reached 88 nm in LOMM, while the cross-sectional geometry of the microgroove was a trapezoid. Perpendicularity of the microgroove sidewall machined by LOMM was better than that by COMM. The tool wear forms in LOMM were coating spalling and slight tool nose breakage. Compared with COMM, the tool life in LOMM was prolonged significantly. It indicates that the proposed hybrid process is an effective and efficient way to fabricate high aspect ratio micro-features with high dimensional accuracy.