(70~100)MeV准单能中子参考辐射场设计

国内基于串列加速器建立了144keV~15MeV的单能中子参考辐射场，解决了20MeV以下能区中子探测器注量、剂量等参数的量值溯源，但尚未建立20MeV以上能区准单能中子参考辐射场。随着航天空间中子探测任务的需要以及地面高能质子加速器的发展，20MeV以上能区准单能中子参考辐射场需求越来越突出。发展20MeV以上能区高能中子参考辐射场对于满足国防需求、推动中子计量学科发展具有重要意义。     

飞机刹车系统防滑功能研究

介绍了某型机防滑刹车系统组成、功能和工作原理,通过某型机机轮、刹车系统不同试验状态性能对比,并与某某飞机机轮、刹车系统进行动力试验数据、防滑性能对比分析,确定防滑刹车系统在通常情况下不工作,是系统的正常工作现象。     

Effects of yaw-roll coupling ratio on lateral-directional aerodynamic characteristics

Experimental investigation of large amplitude yaw-roll coupled oscillations was conducted in a low-speed wind tunnel using an aircraft configuration model. A special test rig was designed and constructed to provide different coupled motions from low to high angles of attack.A parameter ‘‘coupling ratio" was introduced to indicate the extent of yaw-roll coupling. At each pitch angle, seven coupling ratios were designed to study the yaw-roll coupling effects on the lateraldirectional aerodynamic characteristics systematically. At high angles of attack, the damping characteristics of yawing and rolling moments drastically varied with coupling ratios. In the coupled motions with the rotation taking place about the wind axis, the lateral-directional aerodynamic moments exhibited unsteady characteristics and were different from the ‘‘quasi-steady" results of the rotary balance tests. The calculated results of the traditional aerodynamic derivative method were also compared with the experimental data. At low and very high angles of attack, the aerodynamic derivative method was applicative. However, within a wide range of angles of attack, the calculated results of aerodynamic derivative method were inconsistent with the experimental data, due to the drastic changes of damping characteristics of lateral-directional aerodynamic moments with yaw-roll coupling ratios.     

热防护材料高温异型传感器校准技术研究

高温异型传感器广泛应用在热防护材料研究领域，因其测温部分比通用温度传感器尺寸短，现有的校准装置无法满足该类传感器的校准需求。针对高温异型传感器无法校准的问题，提出了一种应用专用高温恒温炉、基于比较法的校准方法，研制了高温异型传感器校准装置，实现了该类温度传感器的量值溯源，并进行了不确定度分析。     

A multi-aircraft conflict detection and resolution method for 4-dimensional trajectory-based operation

Conflict Detection and Resolution(CDR) is the key to ensure aviation safety based on Trajectory Prediction(TP). Uncertainties that affect aircraft motions cause difficulty in an accurate prediction of the trajectory, especially in the context of four-dimensional(4D) Trajectory-Based Operation(4DTBO), which brings the uncertainty of pilot intent. This study draws on the idea of time geography, and turns the research focus of CDR from TP to an analysis of the aircraft reachable space constrained by 4D waypoint constraints. The concepts of space–time reachability of aircraft and space–time potential conflict space are proposed. A novel pre-CDR scheme for multiple aircraft is established. A key advantage of the scheme is that the uncertainty of pilot intent is accounted for via a Space-Time Prism(STP) for aircraft. Conflict detection is performed by verifying whether the STPs of aircraft intersect or not, and conflict resolution is performed by planning a conflict-free space–time trajectory avoiding intersection. Numerical examples are presented to validate the efficiency of the proposed scheme.     

激光冲击强化对钛合金高温微动疲劳寿命的影响

为了解高温工作环境下激光冲击强化工艺(LSP)对钛合金材料微动疲劳寿命的影响,开展了强化前后TC11钛合金在室温、300°C和500°C下的微动疲劳试验并测试了试验件表层的残余应力及硬度。结果表明:随着温度的升高,激光冲击强化对TC11钛合金微动疲劳寿命的提高倍数逐渐减小。在轴向载荷为400MPa,法向载荷为65.5MPa时,经激光冲击强化后TC11钛合金试验件在室温、300°C和500°C下的微动疲劳寿命分别为强化前的5.5倍、3.5倍和1.7倍;强化后试验件表层的残余应力会在高温下发生松弛,且松弛程度会随温度的升高而增大,这是激光冲击强化效果随温度升高而逐渐弱化的主要原因。     

流-固-推进耦合下的机体/推进一体化性能分析

吸气式空天飞行器的一体化性能随扰动变化的敏感性高,在高马赫数飞行条件下,有必要开展流-固-推进耦合性能分析。针对机体/推进一体化布局的吸气式飞行器,明确一体化部件之间的耦合关系和耦合问题,利用CFD、有限元和准一维流方法,结合本征正交分解(Proper Orthogonal Decomposition,POD)降阶手段,建立吸气式空天飞行器流-固-推进多物理场耦合快速分析方法,并开展多场耦合特性分析。结果表明:(1)进气道压缩面的流-固耦合导致出口静压的最大振荡振幅约为平均静压的21.6%,而出口马赫数的最大振幅约为平均马赫数的8.45%。(2)进气道出口性能的振荡会影响发动机的推力性能,导致推力振荡幅值可达平均值的31%,且随着时间的推移,会在进气道外压缩流场产生大量的气动涡,涡结构进入进气道后会导致进气道出口性能的持续下降,进一步削弱了发动机的平均推力性能。     

高长径比银纳米线的制备及其透明导电薄膜性能

为改善产品长径比,本文在经典多元醇法的基础上,经过常压滴注路线和密闭溶剂热路线分别制备银纳米线。详细讨论了反应时间、反应气氛及反应物投料比等相关参数对银纳米线的产率和长径比的影响。发现密闭溶剂热法在缓解环境污染的同时降低了生长过程中的扰动,所得银纳米线平均直径约55 nm,长度约65μm,长径比接近1 200。以之制备的透明导电薄膜的方阻仅6Ω,波长550 nm下透光度为78. 6%,品质因数(FOM)高达246,优于常压滴注路线。     

基于响应曲面法的高速内冷铣削AISI304不锈钢铣削力

针对硬质合金刀具高速内冷铣削AISI304不锈钢时,切削力大、切削温度高及加工表面质量低的问题。基于响应曲面中心复合设计方法进行高速内冷铣削实验,建立了铣削力分量二阶回归预测模型,并进行了实验验证。对比了干式与内冷铣削后的加工表面质量,分析了铣削参数对铣削力分量的影响规律,以铣削力分量最小为目标优化了铣削参数。结果表明:进给力和径向力的预测值与实验值的误差分别为4. 77%和6. 16%;内冷铣削的Ra为0. 193～0. 327μm;对铣削力分量的影响是铣削深度转速进给量,随着铣削深度和转速的增加,进给力先升高后降低,径向力逐步增加,铣削深度与转速的交互作用对进给力和径向力的影响显著;转速11 643. 63 r/min、铣削深度1 mm、进给量0. 08 mm/r为最优铣削参数组合。