300 MVA脉冲发电机组滑差方式起动过程研究

介绍了300 MVA脉冲发电机组的滑差装置。对机组采取滑差方式的起动过程进行了分析和等效建模。根据机组实际起动过程电气波形,利用非线性规划模型,建立了滑差装置液体电阻等效仿真模型,并代入机组参数对起动过程进行仿真,仿真结果和实际波形吻合,验证了模型的正确性。在此基础上,为了使机组的转速达到额定转速,提出在滑差装置液体电阻低位时并入两级固体金属电阻后短接的方案,给出了两级固体金属电阻的阻值等理论参数,并通过仿真验证了方案的可行性。建立的仿真模型可以作为研究不同参数、不同控制策略下的机组起动过程动态特性的重要工具。     

基于双环滑模控制的直/气复合控制系统设计

直/气复合控制导弹具有强干扰、强非线性以及强耦合等特点，传统的姿态控制器难以适用于该种复杂干扰并存的情况，文章提出了基于双环滑模控制的直/气复合控制器。首先采用有限时间收敛趋近律分别构造内外环滑模控制器，并将角速度回路的滑模变量量化为直接力指令，以解决空气舵与姿控发动机之间的耦合问题。接着使用非线性扩张状态观测器估计综合干扰，从而设计控制器补偿侧向喷流干扰及模型不确定性等综合干扰的影响。然后基于李雅普诺夫方法证明了控制系统闭环稳定，分析了干扰补偿对控制器收敛域的影响。最后仿真结果表明，该方法跟踪速度快，动态过程平稳，具有较强的干扰抑制能力，具有很强的鲁棒性。     

SiC/CVD SiC复合涂层的抗氧化及抗热震性能研究

为了提高C/SiC复合材料耐高温性能,采用泥浆浸渍裂解与真空化学气相沉积(CVD)在材料表面制备了SiC/CVD SiC复合涂层,通过XRD、SEM分析了涂层组成与结构;研究了复合涂层的高温抗氧化(700～1 500℃)和抗热震性能。结果表明,泥浆浸渍法制备的SiC涂层具有一定的封孔效果,可使材料开孔率下降,但高温抗氧化效果并不佳,1 200℃氧化10 min后材料弯曲强度保留率下降明显仅有86%。CVD SiC涂层结构致密,与SiC封孔涂层结合较好,在700～1 500℃具有较好的抗氧化效果,随着氧化温度的升高,氧化后涂层完好,表面O元素逐渐增加,材料失重率缓慢增加但不大于0.5%,且材料性能并未下降。涂层材料在1 200℃-10 min短时热震5次后材料弯曲强度保留率仍有95%以上,且未出现开裂、剥落等热震损伤。在1 200℃-30 min长时热震10次后,涂层材料基本被完全氧化,材料失去保护作用,弯曲强度下降至90%左右。     

基于连续损伤模型的复合材料波纹梁压溃分析

复合材料的耐撞性受到了广泛重视,而波纹梁因其优异的抗屈曲构型被广泛应用于飞机翼梁和直升机底板等经常发生碰撞的结构中。进行了复合材料波纹梁的屈曲分析,研究了高度对波纹梁破坏模式的影响。建立复合材料波纹梁的连续损伤单波模型,层内基于Hashin判据建立含损伤因子的损伤刚度矩阵,层间根据二次名义应力准则和B-K准则模拟损伤演化,并通过典型复合材料波纹梁压溃试验验证了所建立模型的正确性。基于单波分析模型,通过施加周期性边界条件和反对称边界条件,研究了多波结构的吸能特性。     

高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

为了研究高主流湍流度下二次流密度比对涡轮导叶全气膜冷却特性的影响,使用热色液晶测量了在主流湍流度为15%,二次流密度比为1.0和1.5下三维涡轮导叶的气膜冷却效率和换热系数。二次流与主流质量流量比为7.0%和12.5%。结果表明:二次流密度比增大可以降低冷气射流的动量,小流量比工况下,在叶片前缘和压力面前半段,动量较低的二次流在高主流湍流度的影响下更易耗散,增大二次流密度比使冷却效率明显降低;大流量比工况下,二次流动量降低使气膜孔后区域冷气贴附性增强,气膜冷却效率和冷气覆盖效果均得到提升。小流量比工况下,二次流密度比增大对叶片表面换热的影响较小;大流量比工况下,二次流密度比增大使吸力面中弦区域和压力面后半段的平均换热系数比分别降低15%和25%。     

Numerical investigation on flow and heat transfer characteristics of supercritical RP-3 in inclined pipe

Numerical simulations of flow and heat transfer to supercritical RP-3 through the inclined tubes have been performed using LS k–e model embedded in Fluent. The physical properties of RP-3 were obtained using the generalized corresponding state laws based on the fourcomponent surrogate model. Mass flow rate is 0.3 g/s, system pressure is 3 MPa, inlet temperature is 373 K. Inclination of the inclined pipe varied from -90° to 90°, with heat flux varied from 300 k W/m~2 to 400 kW/m~2. Comparison between the calculated result and the experimental data indicates the range of error reasonable. The results of ±45° show that temperature inhomogeneity in inclined pipe produce the secondary flow in its cross section due to the buoyancy force. Depending on the strength of the temperature inhomogeneity, there will be two different forms of secondary flow and both contribute to the convective heat transfer in the pipe. The secondary flow intensity decreases when the inhomogeneity alleviates and thermal acceleration will play a leading role. It will have a greater impact on the turbulent flow to affect the convective heat transfer in the pipe. When changing the inclination, it affects the magnitude of the buoyant component in flow direction. The angle increases, the buoyancy component decreases. And the peak temperature of wall dominated by the secondary flow will move forward and increase in height.     

Numerical analysis of hypersonic thermochemical non-equilibrium environment for an entry configuration in ionized flow

A theoretical methodology for thermochemical non-equilibrium flow combing with the HLLC (Harten-Lax-van Leer Contact) scheme was applied to study the hypersonic thermochemical non-equilibrium environment of an entry configuration in ionized flow. A two-temperature controlling model was utilized and the Gupta’s 11 species (N₂, O₂, NO, O, N, NO⁺, N₂⁺, O₂⁺, N⁺, O⁺, e^?) thermochemical non-equilibrium model was taken. Firstly, numerical calculations of hypersonic thermochemical non-equilibrium environments for different aerodynamic shapes were carried out to verify the reliability of the method above. Then, the method was used to research the effects of ionization and wall catalysis on the hypersonic thermochemical non-equilibrium environment of the entry configuration in ionized flow. The shock stand-off distance can be reduced by thermochemical reactions but doesn’t continue to decrease significantly when ionization occurs. The shock stand-off distance calculated by the 11 species model is 4.2% smaller than that calculated by the 5 species (N₂, O₂, NO, O, N) thermochemical non-equilibrium model without considering ionization. Ionization reduces wall heat flux but increases wall pressure a little. The effect of ionization on aerothermal loads is greater than that of aerodynamic loads. The thermochemical reactions of electrons and ions catalyzed at the wall increase wall heat flux significantly but make a small change in wall pressure. The maximum wall heat flux obtained by only considering the electrons and ions catalyzed at the partially catalytic wall condition is 11.8% less than that calculated at the super-catalytic wall condition.     

一种针对局部结构的有限元模型修正方法

针对实际结构有限元模型（FEM）的建模误差通常仅存在于局部区域，提出了一种对局部结构单独进行模型修正的方法。首先，根据频响函数（FRF）解耦理论得到由残余结构频响函数与包含待修正参数的局部结构动刚度所重构的整体结构频响函数的拟合值，然后通过迭代优化使其与测量值的残差最小化，从而得到参数的极大似然估计。在此基础上，将残差关于参数的灵敏度以局部结构动力学矩阵表示，建立了模型修正的基本方程，利用整体结构的测试数据即可直接对分离出来的局部结构进行模型修正。最后，对喷气式飞机和三角机翼飞机分别进行了数值模拟和实验研究，验证了所提方法的可行性和有效性。结果表明，所提方法可以成功地用于仅局部区域含有建模误差的实际结构有限元模型的修正，修正后的有限元模型的动态特性与实际结构有较好的一致性。     

Modeling the effects of green alternative on heat island mitigation of a meso level town,West Bengal,India

Urban heat island (UHI) is emerged as a ubiquitous phenomenon that affects the outdoor thermal comfort. Hence urban microclimatic studies using numeric simulation software to find out adaption strategies are attracting the great attention of researchers and policymaker. Number of scientists carried out their research on this topic using different tools and technique whereas ENVI-met model is the most widely used simulation tools. The present study intended to examine the implication of green infrastructure of the town on enhanced microclimatic condition and to evaluate the best suitable mitigation strategy modelling cool city with ENVI-met software (V4). Five greening condition such as existing UHI condition (C1), 100% greening of roof (C2), 100% greening of roof and walls (C3), 50% greening of roof and walls (C4) and: Plantation at suitable area with 50% greening of roof and walls (C5) have been taken into consideration for the microclimate simulation for all three selected sites. Among these five conditions, C3 for the open mid-rise and compact low-rise, C5 for the open low-rise are identified as one of the most suitable strategies which can reduce the air temperature of peak hours by 2.6 °C, 1.33 °C and 1.87 °C respectively. These models are validated by simple linear regression between simulated and existing air temperature in case of existing UHI condition (C1) and in all the cases coefficient of determination value is high such as for open mid-rise, compact low-rise and open low-rise, it is 0.92, 0.92 and 0.75 respectively. Therefore it can be concluded that the application of those strategies can improve the urban thermal environment as well as the outdoor thermal comfort of English bazaar Town and its surroundings.     

场协同原理在高超声速化学非平衡流动中的推广

应用理论分析与数值模拟方法，将对流传热的场协同原理从不可压缩流动推广至高超声速化学非平衡流动中。结果表明，高超声速化学非平衡层流与湍流的热流密度取决于流动的当地单位体积的动量与单位质量总焓梯度的协同。用当地单位体积的动量与单位质量总焓梯度的协同研究高超声速化学非平衡流动的壁面传热问题，对层流流动下的对流传热，不但计及了高超声速化学非平衡流的密度变化对热流密度的影响，而且包括了静焓梯度、压力梯度、边界层内的分子黏性剪切效应对热流密度的作用；对湍流问题，除了上述层流流动各项对热流密度的影响外，还计及了雷诺剪切应力对热流密度的作用。考虑到高超声速化学非平衡流静焓的定义，高超声速化学非平衡层流及湍流的场协同同时计及所有组分的平动能、转动能、振动能及电子能等梯度的贡献。