Multi-faults diagnosis of rolling bearings via adaptive customization of flexible analytical wavelet bases

Multi-faults detection is a challenge for rolling bearings due to the mode mixture and coupling of multiple fault features, as well as its easy burying in the complex, non-stationary structural vibrations and strong background noises. In this paper, a method based on the flexible analytical wavelet transform (FAWT) possessing fractional scaling and translation factors is proposed to identify multiple faults occurred in different components of rolling bearings. During the route of the proposed method, the proper FAWT bases are constructed via genetic optimization algorithm (GA) based on maximizing the spectral correlated kurtosis (SCK) which is firstly presented and proved to be efficient and effective in indicating interested fault mode. Via using the customized FAWT bases for each interested fault mode, the original vibration measurements are decomposed into fine frequency subbands, and the sensitive subband which enhances the signal-to-noise ratio (SNR) is selected to exhibit the fault signature on its envelope spectrum. The proposed method is tested via simulated signals, and applied to analyze the experimental vibration measurements from the running roller bearings subjected to outrace, inner-race and roller defects. The analysis results validate the effectiveness of the proposed method in identifying multi-faults occurred in different components of rolling bearings.     

超静超稳卫星碰振动力学建模

针对分离式卫星载荷模块(PM)受到扰动时可能与服务模块(SM)发生碰撞的问题，综合音圈电机反电动势(back-EMF)和柔性线缆动力学的效应，基于牛顿欧拉法建立了分离式卫星(DFP)载荷模块动力学模型。基于Hertz接触理论，推导了分离式卫星碰撞过程中连续接触力模型，并分析了碰撞过程中产生的接触力对载荷模块指向精度和指向稳定度的影响。数值仿真结果表明，碰撞使得载荷模块指向精度和指向稳定度下降5个数量级，碰撞后载荷模块可再次恢复到超静超稳工作状态，恢复时间超过1400 s。本文建立的碰撞模型对研究分离式卫星碰撞规避和碰撞控制具有重要意义。     

新型柔索式杆束结构压紧释放装置

针对空间机械臂、空间可展开天线等空间机构在收拢状态的杆束结构压紧与释放问题，提出一种基于柔性索捆绑压紧与热刀释放的新型压紧释放装置。建立了柔索式压紧释放装置锁紧状态的力学模型，分析了静态压紧和考虑惯性载荷情况下的绳索预紧力变化情况，得到了满足可靠压紧的绳索预紧力设计值。基于质量和刚度等效，设计了机械臂杆束结构力学等效件，并进行了正弦与随机振动力学试验。试验结果验证了所设计的柔索式杆束结构压紧释放装置的可行性，并可以推广到具有复杂包络的杆束结构压紧释放中。     

不同重力环境下间隙铰链关节磨损分析

为研究不同重力环境对空间机构间隙铰链关节磨损的影响，将机械系统摩擦学行为和动力学行为相耦合，建立了磨损与动力学耦合分析模型和数值计算框架。首先采用非线性弹簧阻尼模型作为间隙处接触碰撞力的计算模型，同时采用Coulomb 法来计算运动副间隙处的摩擦力，进而建立了含间隙的机构动力学模型；然后通过基于Archard磨损模型二次开发的ANSYS程序来计算磨损，其中运用节点位移的方法来描述磨损过程。结果表明：当间隙关节转速较低时，重力对于关节轴承的磨损分布和磨损程度的影响很大，轴承出现集中磨损现象，磨损间隙急剧增加，严重影响机构的性能和精度；随着关节转速升高，重力对间隙关节磨损的影响逐渐减弱，轴承的磨损分布、磨损程度和关节最大磨损间隙的增长率将逐渐与微重力环境下趋同。     

A compliant polymorphing wing for small UAVs

This paper presents the development of a novel compliant polymorphing wing capable of chord and camber morphing for small UAVs. The morphing wing can achieve up to 10% chord extension and ±20° camber changes. The design, modeling, sizing, manufacturing and mechanical testing of the wing are detailed. The polymorphing wing consists of one continuous front spar fixed to the fuselage and a rear spar on each side of the wing. Each rear spar can translate in the chordwise direction (chord morphing) and rotate around itself (camber morphing). A flexible elastomeric latex sheet is used as the skin to cover the wing and maintain its aerodynamic shape whilst allowing morphing. The loads from the skin are transferred to the spars using the compliant cellular ribs that support the flexible skin and facilitate morphing. Pre-tensioning is applied to the skin to minimize wrinkling when subject to aerodynamic and actuation loads. A rack and pinion actuation system, powered by stepper motors, is used for morphing. Aero-structural design, analysis and sizing are conducted. Performance comparison between the polymorphing wing and the baseline wing (non-morphing) shows that chord morphing improves aerodynamic efficiency at low angles of attack while camber morphing improves efficiency at high angles of attack.     

含多部位损伤搭接结构应力强度因子三维有限元分析

应力强度因子(Stress intensity factor,SIF)分析是含多部位损伤(Multiple site damage,MSD)结构剩余强度和裂纹扩展寿命预测的基础和关键。考虑接触与摩擦,建立了含MSD搭接结构的三维有限元模型,研究了不同裂纹长度、铆钉类型以及损伤模式下裂纹尖端SIF分布情况和变化规律。结果表明,搭接件孔边裂纹Ⅰ型SIF起主导作用,Ⅱ型和Ⅲ型SIF可忽略不计。由于次弯曲、铆钉变形和板厚度等因素,SIF在外表面最小,接触面一侧较大,最大值多位于蒙皮内部。MSD会使裂纹间的干涉作用增强,SIF增大,且裂纹间距离越近干涉作用越强。裂纹长度相同时,埋头铆钉的孔边裂纹SIF积分均值大于平头铆钉,且接触面的SIF埋头铆钉大于平头铆钉,外表面则相反。     

某型飞机机体机翼接头裂纹分析及维修

针对某型飞机机体机翼左接头部位存在裂纹的现象．对裂纹产生原因进行了分析,并利用有限元软件,对接口部位的简化模型进行两种危险情况加载计算,结果表明此裂纹为疲劳裂纹．在修理中采用加强件代替原垫圈提高了疲劳强度。     

基于子模型方法的钉群连接结构强度分析研究

为了准确高效的进行飞机复合材料钉群连接结构的损伤分析和强度预测,研究了子模型方法在复杂连接结构分析中的应用技术,构造了包括总体模型和两级子模型的钉群连接结构分析模型体系,提出了子模型中螺栓连接结构的建模策略和复合材料结构损伤模拟的方法,确立了对应于损伤模式的结构破坏判据。采用本文提出的方法对波音787复合材料壁板进行接...     

携带晃动燃料柔性航天器姿态机动中的同宿环分叉研究

本文研究了带液体晃动和柔性附件的耦合航天器系统在液体燃料耗散和柔性附件扭转振动的作用下,经历从最小惯量轴到最大惯量轴姿态机动中的混沌动力学行为.将液体晃动等效为球摆模型并由此建立了带柔性附件充液航天器多体耦合系统动力学模型.首先推导出耦合系统动力学方程并采用Melnikov积分预测受扰系统稳定与不稳定流形是否横截相交,得到了参数形式表达的混沌运动解析判据,这对航天器的设计有重要的指导意义.研究发现,混沌的发生依赖于刚体形状,阻尼比,充液比和扭转振动频率.此外,在经过被动再定向姿态机动后,由于液体晃动的本质非线性特性,充液航天器最终将进行大章动角的周期极限环运动而非绕着最大惯量轴自旋.     

多层波纹管焊接接头设计与焊接工艺研究

介绍了多层波纹管焊接接头结构形式,分析了多层波纹管的焊接工艺性及工艺难点。采用滚焊+熔焊的焊接工艺,解决了焊接后焊缝气孔缺陷、熔深浅的问题。改进后的批产试验件焊缝一次交检全部达到I级标准,并通过地面单元试验考核。