A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

火星表面热环境对航天器热控影响分析

火星大气对太阳辐射产生吸收和散射作用，同时还将与火星表面航天器发生对流换热。热设计时难以直接评估对流、辐射和导热三种换热对航天器的影响，从而确定主要的控温途径。在调研火星表面辐射、大气等热环境的基础上，从线性化传热系数和对流辐射比的角度对比分析了辐射、对流和导热对航天器的影响。器表辐射传热系数随光学属性和温度的变化范围为0.3～1.4W/(m2·℃)，对流传热系数随风速变化为0.2～1.5W/(m2·℃)，器内导热传热系数可控制在0.25W/(m2·℃)以下。结果表明，太阳辐射较火星表面和天空辐射而言是主要外热源，航天器表面的辐射和对流换热为两条并联换热途径，两者均可成为主要换热途径，器内导热传热是控制航天器内外隔热的主要可控因素。     

Solar sailing in realistic mode,based on a locally-optimal control laws

Ballistic design of solar sailing missions in the solar system is composed of defining the design parameters, the control programs, and the trajectories that provide performance goals of a flight. The use of a solar sail spacecraft imposes specific restrictions on mission parameters that include the degradation limit on the flight duration, the maximum temperature of solar sail's surface, the minimum distance from the Sun, the maximum angular velocity of the spacecraft's rotation and others.Many authors considered the impact of these restrictions on the design of the mission separately, but they used a sophisticated method of finding the exact optimal motion control or applied the most straightforward laws of motion control. This paper uses local-optimal control laws at the complete mathematical models of motion and functioning of solar sail spacecraft to describe a technique of designing interplanetary missions. The described method avoids the need to obtain an accurate optimal solution to the control problem and does not cause significant computational difficulties.     

涡轮基组合循环发动机分布式控制系统通信网络混合拓扑结构优化方法

涡轮机组合循环(Turbine based combined cycle,TBCC)发动机控制系统通信网络拓扑结构是其分布式控制系统方案设计的重要部分,优化网络拓扑结构可提高发动机推重比和控制系统可靠性。本文基于智能优化算法提出TBCC分布式控制系统网络拓扑结构优化方法。基于图论建立TBCC几何模型和网格模型,以重量和可靠性为优化性能指标,同时考虑发动机表面高温区域以及控制节点的工作可靠性,分别采用粒子群算法和遗传算法优化星形结构中智能中央节点位置、中央节点的环形拓扑结构,获得星形-环形混合拓扑结构。仿真实例表明,基于本文方法优化所得的混合拓扑结构相较于星形集中式控制结构,系统重量降低了51.9%。     

多臂空间机器人的视觉伺服与协调控制

针对多臂空间机器人自主目标抓捕任务，首先建立多臂空间机器人的运动模型和其与目标的相对运动模型，采用Kane方法建立多臂空间机器人的动力学模型；其次，研究基于视觉伺服的机械臂在线轨迹规划算法，并引入零反作用机动，消除机械臂运动对平台姿态的扰动；再次，在不使用零反作用机动功能时，分别使用基于角动量前馈补偿的协调控制算法和逆动力学方法设计了协调控制器，在机械臂运动时保持平台姿态和相对目标的位置。最后，开发了基于Matlab的仿真软件MASS（多臂空间机器人仿真），仿真结果校验了上述方法的有效性。     

轨控大干扰下的系统角动量管理

摘要： 针对利用角动量交换装置系统实现轨控期间姿态维持的情况，研究当轨控推力器存在大力矩扰动时系统角动量管理方法.结合对地运行航天器轨道运动特性，分析轨控干扰力矩的积累角动量变化规律；考虑角动量管理装置系统的角动量存贮容量，基于角动量积累规律提出了一种结合偏置角动量建立与对称分布轨控位置选择的系统角动量管理方法，实现了对称轨控位置积累角动量互相抵消的自平衡效果，极大程度地提高轨控效率且避免系统角动量饱和现象.所提出的方法适用于喷气欠驱动控制系统，方法的有效性通过了数学仿真验证及在轨型号应用.     

空间载荷机柜热控设计的仿真研究

空间站主动热控系统的作用是提供和保持航天员、仪器设备和结构部件所要求的温度、湿度和风速等热环境。本文以空间载荷机柜为热控系统的基本单元，建立了以单相流体循环回路为基础、采用液冷结合风冷的冷却方式的载荷机柜数学模型；介绍了模糊增量控制算法的工作原理；提出了采用模糊增量控制算法，以液冷支路进出口温差和风冷支路冷却量占总冷却量的比值为控制目标的反馈控制策略。同时文章采用数值模拟方法研究了控制系统的动态响应效果。仿真结果显示，模糊增量控制算法具有响应迅速、超调量小、无静态误差的特点，控制策略满足有效性、稳定性和高精确度的要求。     

Sliding mode control design for oblique wing aircraft in wing skewing process

When the wing of Oblique Wing Aircraft (OWA) is skewed, the center of gravity, inertia and aerodynamic characteristics of the aircraft all significantly change, causing an undesirable flight dynamic response, affecting the flying qualities, and even endangering the flight safety. In this study, the dynamic response of an OWA in the wing skewing process is simulated, showing that the three-axis movements of the OWA are highly coupled and present nonlinear characteristics during the wing skewing. As the roll control efficiency of the aileron decreases due to the shortened control arm in an oblique configuration, the all-moving horizontal tail is used for additional roll and the control allocation is performed based on minimum control energy. Given the properties of pitch-roll-yaw coupling and control input and state coupling, and the difficulty of establishing an accurate aerodynamic model in the wing skewing process due to unsteady aerodynamic force, a multi-loop sliding mode controller is formulated by the time-scale separation method. The closed-loop simulation results show that the asymmetric aerodynamics can be balanced and that the velocity and altitude of the aircraft maintain stable, which means that a smooth transition is obtained during the OWA’s wing skewing.     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

一种未来大型天地往返运输系统平台气动方案

针对未来低运行成本、可直接水平起降、重复使用的大型天地往返运输系统平台飞行器研制所需重点解决的全速域气动力性能需求与气动热防护匹配等难题，分析了典型航天飞机方案所存在的能量运行缺陷等主要问题及可能的改善方案。基于放宽气动热防护设计、涡轮/冲压/火箭发动机三动力组合、嵌套式旋转机翼全速域变体、在爬升阶段将飞行动能转化为高度势能以及再入阶段“跳跃式”盘旋减速飞行轨迹控制等设计思想，从能量损失速率控制和回收利用等角度出发，开展了一种新型大型天地往返运输系统平台气动布局概念设计研究。全速域气动力/热性能工程估算以及内/外流整体气动效能初步分析结果表明，该方案可有效满足整个飞行包线内的升重平衡需求，相比航天飞机方案具有显著的整体气动效能优势，值得进一步开展深入研究。