燃油离心泵多目标优化设计及仿真分析

针对燃油离心泵高效、高抗汽蚀优化设计问题,进行了基于损失模型和SQP算法下的多目标优化设计并进行了仿真应用。首先,考虑叶轮、蜗壳等通流部件内的水利损失、容积损失以及机械损失,建立表征离心泵效率的综合损失模型；结合基于必须汽蚀余量计算下的汽蚀表征函数以确定离心泵多目标函数。进而,利用SQP算法构造合理的适应度函数,结合约束条件确定离心泵多目标优化设计的数学模型。其次,对某型燃油离心泵进行基于SQP算法的优化设计并与其他常用优化算法进行对比。可以看到：各优化算法的最优结果几乎相似,但SQP算法对多维非线性方程组优化求解所用的迭代步数相对较少。最后,利用CFD技术进行仿真及外特性预测,以验证基于SQP算法下燃油离心泵多目标优化设计的有效性。结果表明：相比传统方法设计的原型离心泵,基于SQP算法优化的离心泵内流场压力分布相对均匀,流动损失更低,且进口流动有利于抗汽蚀性能；从外特性结果来看,基于SQP算法优化的离心泵高效工作区域相对宽广,必须汽蚀余量相对较低,抗汽蚀性能有所改善。     

轻量化红外成像制导镜头设计与仿真

根据红外成像制导系统的轻量化、小型化、低成本发展需求，针对制导系统中的光学镜头进行轻量化设计。通过分析超透镜的波前调控原理和加工工艺，利用传输相位调控原理设计了基于硅和氟化钡材料的中红外波长超透镜，工作波长3 μm,镜头厚度小于1 mm，口径50 mm时重量小于10 g，热膨胀系数较低环境适应性好。利用时域有限差分法对超透镜进行了仿真，通过设置对称边界条件缩短了仿真时间。仿真结果表明，当超透镜数值孔径为0.45时，聚焦效率为85%，焦斑半高宽3.4 μm。     

基于虚拟安全域的多级安全访问控制

虚拟化技术作为云计算的核心技术,相对于传统技术具有节约开销、易于管理、灵活制定等优势,成为业界应用的热点技术。文章研究了传统的BLP多级安全模型,并改进了该模型应用于虚拟化系统访问控制,结合虚拟安全域的概念,设计实现了虚拟化系统访问控制模型,主要结合分级分域原则对虚拟机之间的通信控制和虚拟机对虚拟磁盘的访问控制进行约束。     

基于随机维纳过程的航空发动机性能衰退研究

针对发动机下发间隔预测的问题，研究了发动机性能衰退规律。基于发动机排气温度裕度（EGTM）数据，建立了随机维纳模型，并使用严酷度因子修正模型，表征不同的工作条件对发动机的影响。利用期望最大化（EM）算法结合贝叶斯定理，对模型参数求解，最终得到了基于性能衰退的发动机平均下发间隔。研究结果表明，在严酷度因子为1.2696的使用条件下，某型号航空发动机性能衰退平均下发间隔为8219循环；基于该模型预测的发动机平均下发间隔与厂商建议的下发时间之间的误差仅为1.7%。     

基于幅频响应特性的半球谐振子频率裂解与固有刚度轴方位角测定方法

半球谐振子频率裂解与固有刚度轴方位角是影响陀螺性能指标的核心因素。提出了一种基于幅频响应特性的半球谐振子频率裂解与固有刚度轴方位角测定方法，采用压电激振台扫频激振，多普勒激光测振仪检测谐振子的幅频响应特性，通过幅频响应特性曲线分析实现频率裂解与固有刚度轴方位角的测定。对该方法进行了理论分析，搭建了实验装置，并对半球谐振子进行了测试，结果表明：该方法频率裂解测量精度优于0.01Hz，固有频率主轴方位角确定精度优于±1.17°，具有良好的可行性，在半球谐振陀螺研制方面具有良好的参考意义。     

燃气轮机周向拉杆转子连接刚度对转子振动特性影响的研究

为研究燃气轮机周向分布式拉杆转子轮盘间存在的连接刚度对轴系转子振动特性产生的影响，本文提出一种基于六自由度的弹簧单元等效方法；首先将轮盘接触刚度与拉杆弯曲刚度同时等效进连接界面，便于使用一维梁单元求解其临界转速与振动响应变化，验证其与全三维有限元法吻合度在3％以内；然后改写了非线性动力学方程，采用谐波平衡法对其进行求解，使用经典Newmark方法验证其准确性；最后使用该等效方法计算了某模拟转子连接刚度对其临界转速、响应特性、非线性特性等的影响。计算结果表明：当连接面剪切刚度与弯曲刚度减小3个数量级，均造成了临界转速的降低和振动响应的提高，而其影响程度可由各阶振型大致推测，且响应幅值受剪切刚度影响较大；使用临界转速趋于收敛时的连接刚度与试验值的对比误差小于2％，较连续模型提升显著；在连接刚度各向异性时，每一阶临界转速均出现两个响应峰值，轴心轨迹变成椭圆；考虑刚度随位移变化（非线性刚度）后，转子的响应峰值发生“歪扭”特性，且该峰值特征随不平衡量、无量纲阻尼等因素变化而呈现“波浪形”变化。     

一种基于虚拟页地址映射的NAND Flash管理算法

本文提出了一种基于虚拟页地址映射的NAND Flash管理算法.该算法通过定义坏块表、对应表等结构，以及设计的坏块替换策略和虚拟页地址到实际物理页地址的转换算法，实现上层软件采用虚拟地址对NAND Flash的无坏块连续页地址访问.该算法是一种高效的地址映射算法，能高效地对数据进行索引，占用SRAM空间较少，使系统达到高性能，并使得闪存使用的更加稳定持久.     

Inverse identification of constitutive parameters of Ti2AlNb intermetallic alloys based on cooperative particle swarm optimization

Ti₂AlNb intermetallic alloy is a relatively newly developed high-temperature-resistant structural material, which is expected to replace nickel-based super alloys for thermally and mechanically stressed components in aeronautic and automotive engines due to its excellent mechanical properties and high strength retention at elevated temperature. The aim of this work is to present a fast and reliable methodology of inverse identification of constitutive model parameters directly from cutting experiments. FE-machining simulations implemented with a modified Johnson-Cook (TANH) constitutive model are performed to establish the robust link between observables and constitutive parameters. A series of orthogonal cutting experiments with varied cutting parameters is carried out to allow an exact comparison to the 2D FE-simulations. A cooperative particle swarm optimization algorithm is developed and implemented into the Matlab programs to identify the enormous constitutive parameters. Results show that the simulation observables (i.e., cutting forces, chip morphologies, cutting temperature) implemented with the identified optimal material constants have high consistency with those obtained from experiments, which illustrates that the FE-machining models using the identified parameters obtained from the proposed methodology could be predicted in a close agreement to the experiments. Considering the wide range of the applied unknown parameters number, the proposed inverse methodology of identifying constitutive equations shows excellent prospect, and it can be used for other newly developed metal materials.     

Influence of TiB2 particles on machinability and machining parameter optimization of TiB2/Al MMCs

In situ formed TiB₂ particle reinforced aluminum matrix composites (TiB₂/Al MMCs) have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB₂ particles, the machinability is still a problem which restricts the application of TiB₂/Al MMCs. In order to meet the industrial requirements, the influence of TiB₂ particles on the machinability of TiB₂/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1) the machining force of TiB₂/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2) the residual stress of TiB₂/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3) the surface roughness of TiB₂/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4) a multi-objective optimization model for surface roughness and material removal rate (MRR) was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material.