Parameter studies and evaluation principles of delamination damage in laminated composites

Delamination represents one of the most severe failure modes in composite laminates, especially when they are subjected to uniaxial compression loads. The evaluation of the delamination damage has always been an essential issue of composite laminates for durability and damage tolerance in engineering practice. Focusing on the most typical and representative elliptical delamination issue, an analytical model simultaneously considering the conservative buckling process and non-conservative delamination propagation process is implemented. Various computational cases considering different delamination depths, directions, aspect ratios, and areas are established, and the predicted results based on the analytical model are carefully compared. Effects of these geometrical delamination parameters on the buckling, delamination propagation, and failure behaviors of composite laminates are thoroughly analyzed, and innovative evaluation principles of the delamination damage have been concluded. It is found that the delamination area is the key factor that truly affecting the failure behaviors of delaminated composites, and the local / global buckling and failure loads show clear linearity with the delamination area, whilst the delamination depth and direction only have slight effects.     

A novel virtual material layer model for predicting natural frequencies of composite bolted joints

A novel virtual material layer model based on the fractal theory was proposed to predict the natural frequencies of carbon fiber reinforced plastic composite bolted joints. Rough contact surfaces of composite bolted joints are modeled with this new proposed approach. Numerical and experimental modal analyses were conducted to validate the effectiveness of the proposed model. A good consistence is noted between the numerical and experimental results. To demonstrate the necessity of accurately modeling the rough contact surfaces in the prediction of natural frequencies, virtual material layer model was compared with the widely used traditional model based on the Master-Slave contact algorithm and experiments, respectively. Results show that the proposed model has a better agreement with experiments than the widely used traditional model (the prediction accuracy is raised by 8.77% when the pre-tightening torque is 0.5 N∙m). Real contact area ratio A* of three different virtual material layers were calculated. Value of A* were discussed with dimensionless load P*, fractal dimension D and fractal roughness G. This work provides a new efficient way for accurately modeling the rough contact surfaces and predicting the natural frequencies of composite bolted joints, which can be used to help engineers in the dynamic design of composite materials.     

基于双滤波器的高精度目标跟踪估计方法

针对连续推力的合作航天器，采用双重无迹卡尔曼滤波(DUKF)算法估计其状态和加速度。通过状态滤波器和参数滤波器的配合，提升滤波精度，完成运动状态和参数的估计，从而实现合作目标的运动轨迹跟踪。与合作航天器相比，非合作航天器存在大小未知、发生时刻未知的机动，无法获得加速度，且信息获取和运动状态的估计难度大。针对非合作航天器，基于简化的相对运动方程，结合天基平台获得目标的观测信息，采用两个扩展卡尔曼滤波(EKF)及基于半正焦弦的机动检测策略实现多未知脉冲机动的运动状态的估计。仿真结果表明：相比于无迹卡尔曼滤波（UKF），DUKF在对合作航天器的状态和加速度估计方面具有更快的收敛速度和更高的滤波精度；对于存在未知机动的非合作航天器，通过对比验证机动检测策略与滤波器切换策略相结合的方法的有效性，该方法能够检测到多次机动并且减少误判。     

流量调节器管路系统自激振荡特性研究

流量调节器管路系统在小流量大压降工况下会出现低频自激振荡现象。为了深入认识自激振荡产生机理，结合某稳流型流量调节器及管路系统，基于流量调节器弹簧振子动力学模型开展数值仿真研究。数值仿真得出自激振荡频率为94Hz，与发动机试验结果一致。分析了流量调节器结构参数对系统稳定性的影响作用，三角形滑阀节流口能够抑制管路系统自激振荡。自激振荡产生机理是液动力随滑阀节流口型面振荡，并对管路系统形成正反馈作用，当流量调节器综合刚度系数<0时，管路系统就失稳产生振荡。某流量调节器的负载特性试验表明，随着流量调节器压降升高，管路系统稳定性变差。仿真获得的幅频特性，稳定边界与试验结果一致。     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

Modelling ignition probability with pairwise mixing-reaction model for flame particle tracking

Reduced order models for ignition analysis can offer insights into ignition processes and facilitate the combustor optimization. In this study, a Pairwise Mixing-Reaction (PMR) model is formulated to model the interaction between the flame particle and the surrounding cell mixture during Lagrangian flame particle tracking. Specifically, the model accounts for the two-way coupling of mass and energy between the flame particle and the surrounding shell layer by modelling the corresponding turbulent mixing, chemical reaction and evaporation process if present. The state of a flame particle, e.g., burnt, hot gas or extinguished, is determined based on particle temperature. This model can properly describe the ignition process with a spark kernel being initiated in a nonflammable region, which is of practical importance in certain turbine engines and has not been rigorously accounted for by the existing models based on the estimation of local Karlovitz number. The model is integrated into an ignition probability analysis platform and is demonstrated for a methane/air bluff-body flame with the flow and fuel/air mixing characteristics being extracted from a non-reacting simulation. The results show that for the spark location being at the extreme fuel-lean outer shear layer of the recirculation zone, PMR can yield ignition events with a significant number of active flame particles. The mechanisms for the survival of the initial flame particles and the entrainment of the survived flame particles into the recirculation zone are analyzed. The results also show that the ignition probability map from PMR agrees well with the experimental observation: a high ignition probability in the shear layer of the recirculation zone near the mean stoichiometric surface, and low ignition probabilities inside the recirculation zone and the top stagnation region of the recirculation zone. The parametric study shows that the predicted shape of the ignition progress factor and ignition probability is in general insensitive to the model parameters and the model is adequate for quantifying the regions with high ignition probabilities.     

基于工业物联网的混流车间机器人自适应调度

随着工业物联网技术与人工智能技术深度融合,物料机器人已广泛应用于物联网车间中。针对车间存在实时动态变化和状况不确定等诸多复杂因素,本文提出以组分层建树和以实时状态为根节点的SP–MCTS(Singleplayermonte-carlotreesearchalgorithm)搜索方法实现车间自适应调度决策。该方法将机器人调度问题转化为马尔科夫决策过程(Markov decision process,MDP),并详细描述车间状态、动作、奖励和策略的表示方法。在实时调度过程中,该搜索方法依据工件组分层建树,搜索中只考虑相邻两组间的状态关系,从而简化计算难度。在子树搜索中,应用SP–MCTS以实时状态为根节点进行搜索,同时应用扩展方法和剪支方法进行策略探索和信息累积,使得在子树内实时状态节点越深,就越能够快速精准获取最优策略。最后,通过实际案例模拟分析,验证了该方法的有效性和优越性。     

火星车转移坡道柔顺性优化设计及动力学分析

对一种抽展式火星车转移坡道开展柔顺性优化设计和动力学分析。首先，分析火星车与存在异面角的坡道的挤压几何原理。然后，设计坡道的间隙机构和限位机构，并计算出机构关键设计参数的最优值，以自适应调整两侧坡道的距离，〖JP2〗减小火星车与坡道护栏之间的相互作用力。最后，对坡道下落过程和火星车在坡道上的行驶过程进行动力学仿真，验证坡道柔顺性优化设计的效果。结果表明：优化后的坡道柔顺性大幅提高，坡道可以自适应调整两侧的距离；使用优化后的坡道，可以有效降低火星车与坡道护栏的作用力，实现火星车在坡道上的安全行驶。     

复杂动态环境下无人飞行器动态避障近似最优轨迹规划

针对复杂动态环境下无人飞行器的动态障碍规避问题，基于合理假设建立了无人飞行器和动态障碍的运动学模型，并综合考虑无人飞行器飞行过程中的终端约束、控制输入约束、安全避障约束等，以能量最少为性能指标构建动态避障问题数学描述。之后，针对终端约束和控制输入约束，依据优化模型预测静态规划算法(OMPSP)生成初始轨迹；针对动态避障问题的不等式约束，引入松弛变量并结合滑模变结构控制方法设计松弛变量动力学，实现对一个、多个或同时多个动态障碍的安全规避；最后，依据有限时间微分动态规划(RHDDP)算法进行轨迹优化，获得满足上述各种约束并能规避动态障碍的近似最优轨迹。