NiCrAl/Diatomite可磨耗封严涂层制备及性能

分别利用大气等离子喷涂技术制备了Ni/Al粘结底层、火焰喷涂技术制备了NiCrAl/Diatomite可磨耗封严涂层，研究了喷涂距离、送粉速率、火焰气体总流量、喷涂角度和氧燃比等喷涂参数对生长速率和涂层硬度的影响。结果表明，在较低的氧燃比条件下（O₂∶C₂H₂<1.6），随着喷涂距离的增大，涂层生长速率逐渐下降，硬度先保持不变后逐渐上升；当O₂∶C₂H₂>1.6时，涂层的生长速率会随着喷涂距离的增大先增大后减小，硬度随之逐渐下降。随着喷枪对基体相对移动速度的增大，涂层生长速率略微下降，硬度略有上升。气体总流量的增大使得涂层的生长速率明显上升，硬度明显下降。随着送粉量的增大，涂层生长速率明显提高，硬度随之先上升后下降。     

钛合金表面抗激光涂层损伤特性及热效应影响研究

实验研究了钛合金和高反射型陶瓷涂层材料抗连续型激光烧蚀的损伤及温度分布特性，并从热效应影响角度对比分析了二者在抗激光损伤效果方面的差异性。研究结果表明：相比于钛合金，高反射型陶瓷涂层材料能有效增强钛合金基底抗激光损伤的能力；在同等激光功率密度辐照下，陶瓷涂层材料能有效提升钛合金基底耐受激光辐照的时间长度。实验结果表明该陶瓷涂层材料的激光损伤阈值比钛合金高约5.8倍。实验发现陶瓷涂层温升速率高于钛合金，但由于陶瓷材料具有较高的反射特性，以及良好的热吸收和热传导特性，因此能使由激光辐照产生的热量在其表面较快地扩散，而降低向基底方向传导的程度，最终提升陶瓷涂层的抗激光损伤阈值。     

可重复使用热防护材料应用与研究进展

可重复使用热防护系统是为高速重复使用飞行器而发展的关键性技术,涵盖了地球大气环境及非地球大气环境下的弹道式再入、高马赫数巡航等应用场景。根据现有高马赫数飞行器热防护现状,对高马赫数飞行器的主要热防护系统类型、特点和使用场景进行了简要介绍。在此基础上,结合国外里程碑式可重复使用飞行器（X-15、SR-71、航天飞机、X-33、X-37B、Spaceliner等）,梳理了可重复使用热防护材料的应用与研究进展,论述了代表性可重复使用热防护材料的发展、性能、研制进度、特点及应用前景。对国外在可重复使用热防护材料研制中的设计及发展思路,以及所存在的主要问题进行了总结归纳,为可重复使用热防护材料未来的发展提供了思路。     

TGO非均匀增长对热障涂层应力演化和破坏机理的影响

采用内聚力模型和热生长氧化层(TGO)非均匀增长子程序,数值模拟了在热循环载荷作用下热障涂层(TBC)内部应力演化规律和开裂行为。涂层失效过程首先是源自陶瓷层(TC)内近波峰位置的拉伸和切应力共同主导的陶瓷层Ⅰ、陶瓷层Ⅱ混合型裂纹;随着循环数增加,则转向由TC内近波峰位置的切应力主导的Ⅱ型裂纹和波峰波谷中间的涂层厚度方向拉伸应力主导的Ⅰ型裂纹。整体非均匀增长和波谷均匀增长模式下的最大拉伸应力经过一定循环数后几乎不再随循环数而增加;而在波峰均匀增长和整体均匀增长模式下,最大拉伸应力则会随着循环数增加持续增长。整体非均匀增长、波谷非均匀增长模式下,20个循环后最大切应力出现在近波峰位置,分别为-16241 MPa和-15428 MPa;而整体波峰均匀增长和整体均匀增长模式下,最大切应力为-11382 MPa和-11198 MPa。对于波谷均匀增长和整体非均匀增长模式,在9个循环后出现界面裂纹。而对于波峰均匀增长和整体非均匀增长模式,在第17个循环出现界面裂纹。     

Corrosion mechanism investigation of TiN/Ti coating and TC4 alloy for aircraft compressor application

It is imperative to develop multifunctional erosion and corrosion resistant coatings for compressor blades of aircraft engines in harsh environment. PVD (Physical Vapor Deposition) technology has the advances in processing erosion-resistant coatings; however, the performance of PVD coatings to combat corrosion depends on various coating defects. Determining and comparing the corrosion performances of PVD TiN/Ti coating and uncoated TC4 alloy was the main objective of present work. The 960 h salt spray corrosion and 116 h hot corrosion tests were conducted to simulate the grounding and working environments of the aircraft compressors. The corrosion mechanisms due to the coating defects such as pinhole, columnar boundary and large grain were analyzed based on the OM, Confocal microscope, electrochemical measurements, SEM, XRD and EDS results. Owing to the disordered state associated with the columnar boundary and the coating defect, nitrogen could be easily replaced by oxygen in the hot corrosion process, these structures were channels for fast diffusion of oxygen. Moreover, the Gibbs energy changes of Ti oxidation and TiN oxidation were thermodynamically calculated according to the working condition of aircraft compressors, and considerable research effort was focused on mapping out the phase diagram of Ti, TiN and high pressure gases. The findings of this research can provide insights into developing multifunctional coatings for future aircraft engines.     

硅橡胶基防热涂层高温压缩行为

为研究硅橡胶基防热涂层高温下的力学性能,针对两种硅橡胶基防热涂层开展高温压缩试验,对其截面的宏观及微观形貌进行分析,并结合高温下的热失重分析,探讨了其高温压缩强度变化规律及机理。研究结果表明:甲基苯基硅橡胶涂层高温热解温度区间主要为500～650℃,最终质量残余率为67.61%,其高温压缩强度在25～800℃呈增加趋势,由于玻璃小球的软化及树脂基体的热解,导致在400及700℃两个温度点的压缩强度降低,但在800℃由于玻璃小球与涂层中填料、烧蚀产物等发生共融,使涂层力学性能显著增加。甲基乙烯基硅橡胶涂层的高温热解温度区间主要为450～800℃,最终质量残余率为89.95%,由于甲基乙烯基硅橡胶涂层在高温热解后产生的陶瓷相,弥补了树脂裂解所带来的强度下降,因此在25～800℃其高温压缩强度较为稳定,并未产生明显衰减。影响硅橡胶基防热涂层高温力学性能的因素主要包括树脂基体的热解以及填料在高温下发生的物理-化学变化。     

Advances in fabrication of ceramic corundum abrasives based on sol–gel process

Corundum abrasives with good chemical stability can be fabricated into various free abrasives and bonded abrasive tools that are widely used in the precision machining of various parts. However, these abrasives cannot satisfy the machining requirements of difficult-to-machine materials with high hardness, high strength, and strong wearing resistance. Although superhard abrasives can machine the above-mentioned materials, their dressing and manufacturing costs are high. By contrast, ceramic corundum abrasives fabricated by sol–gel method is a cost-effective product between conventional and superhard abrasives. Ceramic corundum abrasives exhibit self-sharpening and high toughness. In this review, the optimization methods of ceramic corundum abrasive properties are introduced from three aspects: precursor synthesis, particle shaping, and sintering. Firstly, the functional mechanism of seeds and additives on the microstructural and mechanical properties of abrasives is analyzed. Specifically, seeds can reduce the phase transition temperature and improve fracture toughness. The grain size and uniformly dense structure can be controlled by applying an appropriate amount of multicomponent additives. Then, the urgent need of engineering application and machinability of special shape ceramic corundum abrasives is reviewed, and three methods of abrasive shaping are summarized. The micromold replication technique is highly advanced and can be used to prepare functional abrasives. Additionally, the influence of a new sintering method, namely, two-step sintering technique, on the microstructural and mechanical performance of ceramic corundum abrasives is summarized. Finally, the challenge and developmental trend of the optimization of ceramic corundum abrasives are prospected.     

含氢 WC/ C 复合涂层在不同润滑油环境的摩擦性能

利用非平衡磁控溅射技术,通过同时离化乙炔气体和共溅射石墨靶与碳化钨靶,在304不锈钢和单晶硅基底上沉积具有Cr过渡层和WC过渡层的含氢WC/C复合涂层。采用扫描电镜、Raman光谱仪、X射线衍射仪、纳米压痕仪等对涂层的微观结构、力学性能进行分析。利用Rtec摩擦磨损试验机对WC/C复合涂层与304不锈钢基底在PAO基础润滑油环境、发动机润滑油环境以及腐蚀性发动机润滑油环境进行摩擦性能测试。结果表明:涂层内含有较多类石墨sp2键,WC1-x相镶嵌在非晶碳基质中构成多相复合结构;涂层的硬度和弹性模量明显高于304不锈钢基底,且其H/E值远高于基底;与304不锈钢基底相比,在三种润滑油环境下涂层均具有较低的摩擦因数和磨损率。     

扩压叶栅剪敏液晶试验与图像处理

基于剪敏液晶涂层(SSLCC)材料的光学特性,发展了适合于内流场狭小空间环境下的SSLCC边界层流动显示技术:设计并加工了微型摄像头-发光二极管(LED)组合式图像采集设备解决拍摄光路问题;基于二维SSLCC图像与三维模型的空间映射关系,建立了真实模型的三维重构方法;通过SSLCC图像光谱Hue色相值转化,实现了液晶图像信息的定量分析。以西北工业大学高亚声速平面叶栅风洞为平台,开展了某扩压叶栅吸力面边界层流态的剪敏液晶流动显示试验。结果表明:所发展的剪敏液晶显示技术可进行叶栅内流场边界层的流态测量;所建立的图像处理方法可为边界层流动特征的辨识及其特征位置确定提供技术支撑;在来流马赫数为0.12、攻角为0°的条件下,叶片吸力面边界层沿流向依次经历了层流边界层分离、再附着及转捩为湍流状态的过程,且边界层的发展受叶栅角区分离流动影响,造成其前缘分离区减小,再附着点和边界层转捩位置向前缘移动。     

WC/C复合涂层海水环境的耐蚀性与摩擦性能

采用非平衡磁控溅射技术在304L不锈钢和单晶硅基底上沉积WC/C多层复合涂层,利用扫描电镜、Raman光谱仪、X射线衍射仪等研究WC/C复合涂层的微观结构,采用纳米压痕仪、划痕测试系统测试涂层的力学性能,利用电化学测试系统和摩擦磨损试验机分别研究涂层在人工配置的海水环境的耐蚀性能和摩擦性能。结果表明:WC/C复合涂层内含有较多类石墨sp2键结构,存在WC1-x相并镶嵌在非晶碳基质中。较之于304L不锈钢基底,WC/C复合涂层在海水环境中表现出更好的耐蚀性与更优异的摩擦适应性。