A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

Modelling ignition probability with pairwise mixing-reaction model for flame particle tracking

Reduced order models for ignition analysis can offer insights into ignition processes and facilitate the combustor optimization. In this study, a Pairwise Mixing-Reaction (PMR) model is formulated to model the interaction between the flame particle and the surrounding cell mixture during Lagrangian flame particle tracking. Specifically, the model accounts for the two-way coupling of mass and energy between the flame particle and the surrounding shell layer by modelling the corresponding turbulent mixing, chemical reaction and evaporation process if present. The state of a flame particle, e.g., burnt, hot gas or extinguished, is determined based on particle temperature. This model can properly describe the ignition process with a spark kernel being initiated in a nonflammable region, which is of practical importance in certain turbine engines and has not been rigorously accounted for by the existing models based on the estimation of local Karlovitz number. The model is integrated into an ignition probability analysis platform and is demonstrated for a methane/air bluff-body flame with the flow and fuel/air mixing characteristics being extracted from a non-reacting simulation. The results show that for the spark location being at the extreme fuel-lean outer shear layer of the recirculation zone, PMR can yield ignition events with a significant number of active flame particles. The mechanisms for the survival of the initial flame particles and the entrainment of the survived flame particles into the recirculation zone are analyzed. The results also show that the ignition probability map from PMR agrees well with the experimental observation: a high ignition probability in the shear layer of the recirculation zone near the mean stoichiometric surface, and low ignition probabilities inside the recirculation zone and the top stagnation region of the recirculation zone. The parametric study shows that the predicted shape of the ignition progress factor and ignition probability is in general insensitive to the model parameters and the model is adequate for quantifying the regions with high ignition probabilities.     

ZL205A合金舱体低压工艺设计及数值仿真应用

针对某ZL205A合金舱体铸件壁薄难充型、壁厚差异大、易产生裂纹等特点,设计了低压底注式浇注工艺。采用立筒缝隙式浇注系统分配充型过程中合金的流量,局部厚大部位放置成形冷铁加快该部位的冷却速度,以控制铸造缺陷的产生。利用ProCast数值仿真软件对工艺进行仿真计算,成功预测了缺陷的产生位置,对工艺方案进行优化,包括倒角过渡、改变型砂使用等,并在优化方案的基础上浇注了舱体铸件,铸件质量良好,没有缩松、缩孔、裂纹等缺陷,符合相关技术要求。     

基于随机维纳过程的航空发动机性能衰退研究

针对发动机下发间隔预测的问题，研究了发动机性能衰退规律。基于发动机排气温度裕度（EGTM）数据，建立了随机维纳模型，并使用严酷度因子修正模型，表征不同的工作条件对发动机的影响。利用期望最大化（EM）算法结合贝叶斯定理，对模型参数求解，最终得到了基于性能衰退的发动机平均下发间隔。研究结果表明，在严酷度因子为1.2696的使用条件下，某型号航空发动机性能衰退平均下发间隔为8219循环；基于该模型预测的发动机平均下发间隔与厂商建议的下发时间之间的误差仅为1.7%。     

基于产品结构的航天器AIT过程多维数据管理系统

文章为解决航天器AIT过程中数据集成度低、数据应用不佳等问题,从数据模型构建、数据集成等方向出发,分析了AIT过程数据在产品结构、时间周期、阶段型号3个维度的演变过程,构建了多维数据模型,并开发基于产品结构的多维数据管理系统。该系统以产品结构为核心,对AIT过程数据进行重新组织,定义不同系统间、不同维度数据之间的关联关系,实现了AIT过程全数据的结构化整合,在此基础上生成了AIT过程数据包。     

低温磨料气射流加工PDMS实验研究

通过自研的低温磨料气射流加工装置进行低温磨料气射流加工聚二甲基硅氧烷(polydimethylsiloxane,PDMS)实验研究,分析了加工时间、加工距离、冲蚀角度和磨料粒径对冲蚀率、孔深和孔横截面形貌的影响。结果表明:随着加工时间的增加,冲蚀率先增大后减小,在第1阶段加工过程中,孔深与加工时间大致呈线性关系,增加加工时间还可使孔底部变平整;存在一个最佳加工距离使孔深最大,当加工距离大于最大加工距离时,孔深将随着加工距离的增加而急剧下降,孔的锥度随着加工距离的增大而增大;当冲蚀角度处于30°～60°之间时,冲蚀率最大,随着冲蚀角度的增加,孔的形状逐步由椭圆形变成圆形;存在一个最佳磨料粒径,使冲蚀率和孔深达到最大;当冲蚀角度小于90°时,低温磨料气射流加工PDMS材料去除机理为塑性去除和脆性去除的结合。     

热塑性定型剂对干铺丝-RTM工艺及力学性能影响

为了研究热塑性定型剂的添加对干铺丝-树脂传递模塑（RTM）工艺的影响，采用PA-6作为热塑性定型剂，通过T-剥离确定定型剂的质量分数，结合试验和工艺仿真，研究了定型剂对预制体面内渗透率的影响，并对其充模过程进行工艺仿真和分析，在此基础上研究了定型剂对环氧复合材料制品层间性能及韧性的影响。渗透率试验和仿真结果表明:加入定型剂后，纤维预制体的沿纤维和垂直纤维的面内渗透率分别降低了55.5%和52.0%；工艺仿真结果与试验结果一致，不同渗透长度下的注胶时间偏差均小于10%。力学性能试验结果表明:加入热塑性定型剂可显著提升环氧树脂复合材料的韧性，Ⅰ型和Ⅱ型层间断裂韧性分别提高了89.3%和54.1%，冲击韧性提高了18.7%，复合材料的层间剪切强度降低了23.6%。      

Sliding mode control design for oblique wing aircraft in wing skewing process

When the wing of Oblique Wing Aircraft (OWA) is skewed, the center of gravity, inertia and aerodynamic characteristics of the aircraft all significantly change, causing an undesirable flight dynamic response, affecting the flying qualities, and even endangering the flight safety. In this study, the dynamic response of an OWA in the wing skewing process is simulated, showing that the three-axis movements of the OWA are highly coupled and present nonlinear characteristics during the wing skewing. As the roll control efficiency of the aileron decreases due to the shortened control arm in an oblique configuration, the all-moving horizontal tail is used for additional roll and the control allocation is performed based on minimum control energy. Given the properties of pitch-roll-yaw coupling and control input and state coupling, and the difficulty of establishing an accurate aerodynamic model in the wing skewing process due to unsteady aerodynamic force, a multi-loop sliding mode controller is formulated by the time-scale separation method. The closed-loop simulation results show that the asymmetric aerodynamics can be balanced and that the velocity and altitude of the aircraft maintain stable, which means that a smooth transition is obtained during the OWA’s wing skewing.     

基于层次分析法的综合射频架构选取技术研究

综合射频系统是作战飞机航空电子系统的重要组成部分，它们是作战飞机通过无线电方式感知外界信息的重要系统。系统架构的选取直接影响了飞机的作战性能，针对以往架构选取依赖大量定性分析而缺乏定量对比问题，提出了基于层次分析法的综合射频架构选取技术，该技术能够有效地根据不同的任务需求和平台需求，综合考虑定量和定性因素，给出更为合理对比分析结果，为综合射频系统的系统设计提供技术支撑。该技术也可推广到航空领域其他多目标决策问题的应用。     

基于成本控制的机队优化配置方法

为了控制航空公司运营成本,实现燃油成本和机组时间成本最小,建立多目标整数规划模型,分析各成本因素所占比例,考虑旅客市场需求、航线频率限制、机队飞机寿命限制及飞机适航限制等因素,并采用层次分析法对模型进行求解。通过算例分析和评价,实现航线资源与机队的最优配置,为航空公司降低可变成本提供理论依据。