纳米碳粉掺杂对激光烧蚀GAP的推进性能影响

实验以含能聚合物聚叠氮缩水甘油醚(Glycidyl azide polymer,GAP）作为激光烧蚀微推力器的靶材。通过对不同浓度纳米碳粉掺杂和靶材厚度下激光烧蚀GAP的比冲、冲量耦合系数和能量转化效率测量，结合靶材喷射羽流图像，分析了纳米碳粉掺杂提高激光烧蚀聚合物靶材推进性能的机理，给出纳米碳粉掺杂的适用方式。实验结果表明：透射式下，掺杂纳米碳粉之后，聚合物对激光的吸收大幅增强，但激光烧蚀推进性能不随掺杂浓度增加而显著提升；纳米碳粉吸收激光能量形成温度极高的局部热区促进聚合物中化学能的释放，是推进性能提升的主要原因；掺杂纳米碳粉之后的GAP烧蚀深度降低，表现出面吸收特性；随着靶材厚度的增加，未完全烧蚀的工质质量增加，使得靶材的利用率大大降低，导致聚合物推进性能下降。实验中掺杂3%纳米碳粉、厚度为54 μm的GAP靶材最优能量转化效率超过250%，适合作为透射式激光烧蚀微推力器的靶材。     

小型回流燃烧室多工况碳黑分布预测

为了研究小型回流燃烧室不同条件下的工作状态,并分析其产生积碳现象的原因,采用k-ε湍流模型、EDC湍流燃烧等模型对该燃烧室多个工况进行数值计算。结果表明,燃烧室性能参数计算值与台架数据较吻合,各个状态下参数相对误差均小于1.37%。根据各工况的温度分布的变化,发现燃烧室火焰随工况降低逐渐向火焰筒头部收缩。计算了各工况蒸发管内的燃油蒸发率,发现蒸发率在低工况时明显降低。根据出口温度分布情况,计算出口温度分布系数OTDF为0.35。分析碳黑粒子的分布,发现积碳现象主要在火焰筒头部,其原因主要是燃烧不充分和冷却气膜的缺失。     

碳纤维复合壳体用基体环氧树脂研究进展

介绍了固体火箭发动机碳纤维缠绕用基体环氧树脂的种类、选择原则及适于碳纤维缠绕用基体树脂的研究进展.     

三种纳米碳材料吸波涂层设计及性能

对纳米炭黑(UC)、特导纳米炭黑(L6)、碳纳米管(CNT)三种材料在8～18 GHz波段吸波涂层进行了优化设计及吸波性能分析.结果表明,三种材料的复介电常数随着纳米碳材料质量分数的增加,其实部和虚部均以不同的速度增大.利用理论计算的Cole-Cole图,结合实验测得的复介电常数,求解出这三种材料理想的介电常数,材料的质量分数和吸波涂层的匹配厚度.结果表明,CNT的吸波效果最好,当CNT质量分数为20％涂层、厚度为1.6mm时,反射衰减率在11.2～ 15 GHz均优于-10 dB吸收峰最大值,达到29.6 dB.     

复合材料泡沫夹芯结构低速冲击损伤研究

随着复合材料夹芯结构在航空领域的广泛应用,对其抗冲击性能的研究变得越来越重要。本文对泡沫夹芯结构的低速冲击问题采用试验及数值分析的手段进行研究,比较了不同冲击能量下泡沫夹芯结构的冲击响应特点,并利用数值分析手段揭示了冲击损伤的破坏机理,同时计算得到了该夹芯结构的临界冲击能量,模拟结果与试验吻合较好,可为工程设计提供一定...     

Low-dose carbon ion irradiation effects on DNA damage and oxidative stress in the mouse testis

To investigate the effects of low-dose carbon ion irradiation on reproductive system of mice, the testes of outbred Kunming strain mice were whole-body irradiated with 0, 0.05, 0.1, 0.5 and 1 Gy, respectively. We measured DNA double-strand breaks (DNA DSBs) and oxidative stress parameters including malondialdehyde (MDA) content, superoxide dismutase (SOD) activity, and testis weight and sperm count at 12 h, 21 d and 35 d after irradiation in mouse testis. At 12 h postirradiation, a significant increase in DNA DSB level but no pronounced alterations in MDA content or SOD activity were observed in 0.5 and 1 Gy groups compared with the control group. At 21 d postirradiation, there was a significant reduction in sperm count and distinct enhancements of DSB level and MDA content in 0.5 and 1 Gy groups in comparison with control. At 35 d postirradiation, the levels of DNA DSBs and MDA, and SOD activity returned to the baseline except for the MDA content in 1 Gy (P < 0.05), while extreme falls of sperm count were still observed in 0.5 (P < 0.01) and 1 Gy (P < 0.01) groups. For the 0.05 or 0.1 Gy group, no differences were found in DNA DSB level and MDA content between control and at 12 h, 21 d and 35 d after irradiation, indicating that lower doses of carbon ion irradiation have no significant influence on spermatogenesis processes. In this study, male germ cells irradiated with over 0.5 Gy of carbon ions are difficult to repair completely marked by the sperm count. Furthermore, these data suggest that the deleterious effects may be chronic or delayed in reproductive system after whole-body exposure to acute high-dose carbon ions.     

复合材料薄壁加筋抛物面天线仿真与优化

采用Patran/Nastran有限元软件对复合材料薄壁加筋抛物面天线进行了建模和仿真分析。重点分析了反射面铺层方式、加筋结构形式以及加强筋铺层对抛物面天线基频的影响。分析结果表明:采用[0/45/-45/90]s铺层形式的反射面基频最高;增加径向和环向筋可大幅提高天线基频,其中加筋结构采用[0/30/90/-30]s铺层可进一步提高天线基频。通过有限元分析确定了基频最佳的复合材料抛物面天线结构,为制备薄壁加筋抛物面天线提供了指导。     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

填加造孔剂法制备泡沫铝及其吸能性能

以尿素为造孔剂,采用填加造孔剂法制备泡沫铝,系统研究了成型烧结温度、孔隙率和孔径大小对泡沫铝吸能性能的影响,在此过程中采用电子万能试验机和数字图像相关(DIC)技术同步测试分析。结果表明:填加造孔剂法可以良好的控制泡沫铝的孔隙率和孔径;泡沫铝的最佳成型烧结温度为650℃,在此温度下,泡沫铝的压缩屈服强度达到10.7 MPa;随着孔隙率的降低,泡沫铝的屈服强度和平台应力逐渐提高,材料吸能性能有显著增强;当孔径小于2.0 mm时,随着孔径的增大,材料的吸能性能小幅提高。DIC技术可以直观的表征泡沫材料力学行为,具有良好的工程应用前景。     

分散方法对碳纳米管/环氧树脂性能的影响

使用超声波振荡法和超声波破碎法两种方法制备了不同含量的碳纳米管/环氧树脂,分析了分散前后碳纳米管的形态,对比了分散方法对环氧树脂固化特性、流变性能、热性能、力学性能的影响,并研究了产生这种现象的机理。研究结果表明:超声破碎分散的CNTs形貌发生一定的变化,分散方法对树脂的固化特性、流变性能影响不明显,但是对树脂的玻璃化转变温度、力学性能影响较为明显。