排序方式: 共有33条查询结果,搜索用时 15 毫秒
1.
2.
以三颗非共轨的Walker星座卫星为研究对象,对航天器无需变轨与其接近的可能性进行研究.将Lambert方法得到的航天器轨道作为初始轨道,利用遗传算法对初始轨道进行优化.对初始轨道在参考时刻位置和速度的改变量进行编码,形成对应的种群.以航天器与星座卫星之间的最近距离为适应度函数,通过种群的繁殖得到优化结果.结合仿真算例,分析了最小二乘算法和遗传算法在轨道优化中的优劣以及接近过程中轨道摄动的影响.结果表明,遗传算法适用于所提出的轨道改进问题.研究结果可为单航天器无需变轨对星座多星接近问题提供理论依据. 相似文献
3.
杨俊 《中国民航飞行学院学报》2013,(1):12-15
大气紊流和风切变对飞行活动影响较大,尤以低空风切变危害最大,严重威胁着民航飞行的安全。鉴于飞行器对抗大气扰动的实际能力有限,正确的飞行对策是回避或改出危险的大气扰动区。本文对某训练飞机着陆进近遭遇风切变时飞机轨迹的变化进行了模拟仿真计算。结果表明,采用恒定迎角策略,即采用最大允许迎角(抖动迎角)和最大油门时,改出效果最佳。同时计算出了某训练飞机在水平风为0时,所能抵抗的最大垂直阵风强度;以及在垂直阵风为0时,所能抵抗的最大水平风强度。 相似文献
4.
Chan-oh Min Dae-woo Lee Kyeum-rae Cho Sung-jin Jo Jang-sik Yang Won-boo Lee 《Aerospace Science and Technology》2011,15(4):269-282
The reentry vehicle is affected by various disturbances such as a wind gust, atmospheric condition or aerodynamic problems in the approach and landing phase. Therefore it is necessary to design a robust control scheme. This paper presents a control scheme using Mamdani fuzzy PD controller. In this paper, the reference trajectories are generated using geometric parameters for disturbed circumstances with 4 cases: nominal, headwind and tailwind, drag increased case. Then, a Mamdani fuzzy PD controller was designed in this study. Twenty-five rules were applied in the knowledge-based system. The max–min method for a fuzzy inference system and the center-of-mass method in defuzzification were used. Finally, guidance and control simulations are performed for verification of proposed controller using generated reference trajectories. In addition, the Monte Carlo simulation is performed considering various disturbances. The results show that proposed Mamdani fuzzy PD controller has reliability and robustness for control of reentry vehicle with wind disturbance in the approach and landing phases. 相似文献
5.
建构主义教学模式对大学生学习方式有重要影响,通过实证研究方法,研究了课堂环境下建构主义教学模式与大学生学习方式之间的内在关系。研究结果表明:以互动性、自主性为特征的建构主义教学模式与深层学习方式显著正相关,教学模式中的自主性对深层动机和策略的影响均显著高于互动性,且自主性可以更为有效地促使学生采用深层学习方式。 相似文献
6.
B样条方法是数据插值、拟合与平滑的重要方法。通过对de Boor-Cox算法计算路径的分析,给出了一种基于向量扩展的B样条基函数求值运算方法。分析表明,该方法具有并行计算结构和递推计算结构,利于计算机实现。同de Boor-Cox递推运算方法比,它能够同步计算出k次B样条的所有k+1个非零函数值,运算效率提高了2k+1倍。在最小二乘法B样条曲线拟合算法中的应用验证了本文算法的有效性。 相似文献
7.
基于磁层粒子动力学理论,根据单粒子方法和偶极磁场模型,在近地球区(L<10),详细讨论了带电粒子的运动特征以及适合不同能量的带电粒子的计算方法,定量分析了磁层中的电场和磁场对各种能量的带电粒子漂移运动的影响.结果表明,对于能量低于10~5eV的电子和10~2eV的质子,宜采用引导中心近似方法;对于能量介于10~5~10~8eV之间的电子和10~2~10~8eV之间的质子,可在部分区域内采用引导中心近似方法,若运动区在10R_e内,则只能采用变步长的轨道法;而对于引导中心方法,粒子能量高于10~8eV时可以忽略电场漂移的影响,粒子能量低于10~3eV时不必考虑磁场漂移的影响,从而简化了引导中心方程组,提高了数值计算效率. 相似文献
8.
张惠玲 《西安航空技术高等专科学校学报》2007,25(1):61-63
通过用一组非线性方程组来逼近线性规划的Kuhn-mcker条件方程,从而将求解线性规划问题转化为一个用Newton迭代法来求解非线性方程组的问题。经数值计算表明,该算法在一般情况下能实现快速收敛。 相似文献
9.
New Cutting Force Modeling Approach for Flat End Mill 总被引:1,自引:1,他引:0
WAN Min ZHANG Wei-hong TAN Gang QIN Guo-hua 《中国航空学报》2007,20(3):282-288
A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions. 相似文献
10.
导弹姿态控制伺服系统的变结构控制 总被引:2,自引:0,他引:2
为消除导弹姿态控制伺服系统变结构控制中的抖振,在状态轨迹与滑动平面夹角变结构控制律的基础上,将原来的二阶系统扩展为n阶。所设计的控制律兼具连续控制律与非连续控制律的优点,动态品质优良。仿真结果验证了理论分析的有效性。 相似文献