全文获取类型
收费全文 | 210篇 |
免费 | 18篇 |
国内免费 | 53篇 |
专业分类
航空 | 154篇 |
航天技术 | 35篇 |
综合类 | 50篇 |
航天 | 42篇 |
出版年
2024年 | 1篇 |
2023年 | 7篇 |
2022年 | 5篇 |
2021年 | 8篇 |
2020年 | 14篇 |
2019年 | 17篇 |
2018年 | 5篇 |
2017年 | 12篇 |
2016年 | 16篇 |
2015年 | 10篇 |
2014年 | 15篇 |
2013年 | 15篇 |
2012年 | 9篇 |
2011年 | 14篇 |
2010年 | 11篇 |
2009年 | 7篇 |
2008年 | 15篇 |
2007年 | 9篇 |
2006年 | 10篇 |
2005年 | 5篇 |
2004年 | 9篇 |
2003年 | 4篇 |
2002年 | 3篇 |
2001年 | 5篇 |
2000年 | 10篇 |
1999年 | 6篇 |
1998年 | 2篇 |
1997年 | 4篇 |
1996年 | 8篇 |
1995年 | 1篇 |
1994年 | 4篇 |
1993年 | 1篇 |
1992年 | 7篇 |
1991年 | 2篇 |
1990年 | 4篇 |
1989年 | 6篇 |
排序方式: 共有281条查询结果,搜索用时 922 毫秒
71.
72.
This paper seeks to outline the temperature effect on the buckling properties of ultra-thin-walled lenticular collapsible composite tube(LCCT) subjected to axial compression.The buckling tests of the LCCT specimens subjected to axial compression were carried out on INSTRON-500 N servo-hydraulic machine in dry state and at the temperatures of 25 C, 100 C and 80 C. The load–displacement curves and buckling initiation loads were measured and the buckling initiation mechanism was discussed from experimental observations. Experiments show that the buckling initiation load, on average, is only about 2.2% greater at the low temperature of 80 C than at the room temperature of 25 C due to the material hardening, demonstrating an insignificant increase in the buckling initiation load, whereas it is about 19.5% lower at the high temperature of 100 C than at the room temperature owing to the material softening, implying a significant decrease in the buckling initiation load. The failure mode of the LCCT in axial compression tests at three different temperatures can be reckoned to be characteristic of the buckling initiation and propagation around the central region until rupture. The finite element(FE) model is presented to simulate the buckling initiation mechanism based on the eigenvalue-based methodology. Good correlation between experimental and numerical results is achieved. 相似文献
73.
74.
复合材料盒段结构屈曲稳定性分析及优化技术 总被引:1,自引:0,他引:1
随着计算机科学和有限元技术的发展,屈曲稳定性问题有限元数值求解技术已经比较成熟,但是在大型飞机结构工程应用中还是由于计算量大、收敛困难而受到限制.特别是在需要反复迭代计算的优化过程中,更是受到该问题的困扰.针对飞机机翼结构中的典型盒段结构,本文研究了基于ANSYS子模型的考虑线性屈曲稳定性约束的优化方法,以及非线性数值计算技术.研究表明,在相同精度要求的条件下,位移求解模型所需网格尺寸可远大于屈曲稳定性模型.本文利用验证结论,采用网格尺寸100mm建立粗模型进行位移求解并确定危险部位,采用网格尺寸10mm建立子模型进行屈曲稳定性求解,从而完成全结构的优化设计.此方法计算效率高,在非线性屈曲稳定性求解以及优化迭代计算中优势明显. 相似文献
75.
转动壳体外压屈曲的有限元分析 总被引:3,自引:1,他引:3
由于转动离心力的影响,壳体的屈曲临界压力随转速的提高而升高。本文推导了转动壳体线性屈曲的有限元公式,并用DMAP语言编制相应的程序修改MSC/NASTRAN的解题步骤考虑离心力完成了分析。还利用MSC/NASTRAN的几何非线性分析功能完成了有初始几何缺陷转动壳体的有限元分析,计算后屈曲的载荷—变形曲线,得出不同转速下的缺陷敏感度曲线。 相似文献
76.
77.
78.
为了提高CFRP圆柱壳的屈曲载荷,降低缺陷对载荷的影响,提出以铺层纤维方向角为设计变量的基于遗传算法的多目标优化方法。采用圆柱壳屈曲理论计算临界载荷和统计方法计算缺陷敏感度,对由个体组成的群体施加选择、交叉和变异等操作,通过多代进化得到问题的pareto最优解。算例优化结果与采用离散方法得到的目标空间比较吻合,验证了方法的准确性和有效性。 相似文献
79.
成形极限曲线(FLC)的新概念 总被引:1,自引:0,他引:1
失稳理论是FLC的理论基础。文章论述了FLC理论研究中存在的问题。指出:一般出厂板的表面状况不会影响板料的集中失稳;板内损伤平面应变时最严重。双拉时,板内损伤的积累、发展,导致应力状态向平面应变漂移;拉压时,载荷失稳后引起的双拉,也会导致平面应变。因此平面应变状态的出现是板料集中失稳的共同原因。在此基础上提出了建立FLC的统一的模型。 相似文献
80.
基于自动铺丝工艺,为获得良好的蜂窝夹层结构自动铺放成型质量,建立了Nomex蜂窝芯在压辊压力下的屈曲、后屈曲和破坏整个失效过程的数值分析方法。采用线性屈曲分析法(特征值分析法)对蜂窝单元进行屈曲分析,得到一阶屈曲模态、屈曲特征值及屈曲载荷;引入初始结构几何缺陷,采用非线性屈曲分析法(弧长法)对Nomex蜂窝单元后屈曲行为进行分析,输出参考点RP-1的载荷-位移曲线,得到弧长法计算的屈曲载荷以及极限载荷值。通过对比试验结果与两种屈曲分析法得到:对于分析临界屈曲载荷,特征值法较弧长法更精确;而弧长法可以更好模拟结构的后屈曲行为,计算结果与试验数据基本吻合,为Nomex蜂窝夹心结构自动铺放成型过程中铺放压力的选取提供参考。 相似文献