Effects of synthetic jet frequency on the separated flow in a diffusing S-duct

Numerical simulations were carried out to investigate the effects of synthetic jet actuation frequency on the separated flow in a diffusing S-duct. The Reynolds number based on the entrance height was 9.78×105. At first, the numerical model was validated with experimental data, and then, the interaction between the separated flow and the synthetic jets at different frequencies was discussed. The results demonstrate that the control effect is significantly dependent on the momentum mixing enhancement between inside of the separated boundary layer and the outer flow. There exists a narrow range of actuation frequency, in which effective separation control can be achieved using synthetic jets. A dimensionless frequency F+=1.0 is identified as the optimal frequency, with a momentum coefficient of 1.62×10-3, the separation area is reduced about 46%, and the aerodynamic performance of the S-duct is also greatly improved compared to uncontrolled case. Further analysis reveals that the choice of actuation frequency is mainly determined by the momentum flux produced by a single ejection and the spacing between adjacent ejections, the optimal frequency case can be understood as a balance between the two factors. In addition, it is found that the synthetic jets can also suppress the secondary flows while decreasing the separation.      

尾缘锯齿降低叶栅噪声的数值模拟

采用大涡模拟与声类比的方法研究了尾缘锯齿对涡轮叶栅噪声的影响.设计了两种不同的尾缘锯齿,对比了Re=3.3×105(基于叶片弦长与叶栅出口速度)下两种不同结构锯齿尾缘叶栅与直尾缘叶栅的声功率.结果表明:尾缘锯齿可以降低叶片吸力面边界层分离噪声约5dB,降低尾缘涡脱落噪声约10dB.进一步的研究表明,尾缘锯齿可以降低叶片尾缘附近表面的压力脉动幅值约50%,将展向相关尺度较大的涡破碎成展向相关尺度较小的涡,并消除尾缘脱落涡,这三者的综合作用使噪声得到降低.      

蜂窝式轴心通风器油气分离性能计算

为对航空发动机蜂窝式轴心通风器油气分离效率进行研究,建立考虑油气双向耦合的流场计算方法及油滴/壁面相互作用模型,在验证通风阻力及油气分离效率可靠性的基础上,对不同转速、通风流量和环境温度下蜂窝式轴心通风器的油气分离效果进行计算和分析.结果表明:转速的增加会使油气分离效率得到提升,而通风流量和环境温度的增加则导致油气分离效率的降低.蜂窝孔结构的加入对通风阻力影响不大,却对通风器的滑油分离过程起主要作用,计算表明其对滑油分离贡献率在80%以上.      

毫秒脉冲等离子体激励改善飞翼的气动性能实验

在来流速度为30m/s时,进行了毫秒脉冲介质阻挡放电等离子体激励改善飞翼气动性能的风洞实验.等离子体激励器布置在飞翼前缘,峰峰值电压为9.5kV时,放电的脉冲能量在0.1mJ/cm量级.通过六分量测力天平测力研究了脉冲激励频率和占空比对升/阻力系数、升阻比和俯仰力矩系数的作用效果.结果表明:等离子体激励可以有效改善飞翼大攻角气动特性;在最佳无量纲脉冲激励频率F+≈1时,临界失速迎角由14°提高到17°,最大升力系数提高10%;占空比对流动控制效果影响较大,减小占空比可以降低能耗,实验中最佳占空比为5%;俯仰力矩系数的变化表明施加等离子体激励改善了飞翼纵向静稳定性.      

引入压力梯度的针对角区分离流动的Spalart-Allmaras模型的改进

针对Spalart-Allmaras（S-A）模型在角区分离计算中的问题,将无量纲的压力梯度引入其涡黏性输运方程的生成项,得到了改进的S-A模型.通过对两套含角区分离的低速压气机叶栅进行验证计算发现:与实验结果相比,原始S-A模型所得的分离区偏大,分离区内壁面压力偏低;而改进模型得到了与实验一致的分离区尺寸以及吸力面、压力面压力系数分布等结果.针对S-A模型涡黏性生成项和耗散项的分析表明:引入的无量纲压力梯度有效的识别了角区分离,在分离区内改变了涡黏性的生成、耗散关系,增大了涡黏性,从而缩小了计算所得分离区,同时在主流区保留了原始S-A模型的计算结果,进而带来了良好的改进效果.      

膨胀效应对激波/湍流边界层干扰的影响

采用直接数值模拟方法对来流马赫数2.9,30°激波角的入射激波与膨胀角湍流边界层干扰问题进行了数值研究。入射激波在壁面上的名义入射点固定在膨胀角角点,膨胀角角度分别取为0°、2°、5°和10°。通过改变膨胀角角度,考察了膨胀效应对干扰区内复杂流动现象的影响规律和作用机制,如分离泡、物面压力脉动特性、膨胀区湍流边界层和物面剪切应力脉动场等。研究发现,膨胀角角度的增大使得分离区流向长度和法向高度急剧降低,尤其是在强膨胀效应下分离泡形态呈现整体往下游偏移的双峰结构。物面压力脉动功率谱结果表明,膨胀角为2°和5°时,分离激波的非定常运动仍表征为大尺度低频振荡,而膨胀角为10°,强膨胀效应极大地抑制了分离激波的低频振荡,加速了下游再附边界层物面压力脉动的恢复过程。膨胀区湍流边界层雷诺剪切应力各象限事件贡献和出现概率呈现逐步恢复到上游湍流边界层的趋势,Görtler-like流向涡结构展向和法向尺度变化剧烈,同时在近壁区将诱导生成大量小尺度流向涡。此外,物面剪切应力脉动场的本征正交分解分析指出,膨胀效应的影响体现在低阶模态能量的急剧降低从而使得高阶模态的总体贡献相对升高。     

风洞T型冲击三通管道流场特性数值模拟

在24 m跨声速风洞进气管路T型冲击三通连接处和隔板位置,每隔一定时间会出现裂纹,影响了风洞的安全稳定运行。为了解裂纹出现的原因,同时为改进设计提供依据,采用CFD(computational fluid dynamics)对风洞现有三通和优化方案进行了对比。控制方程为三维黏性不可压缩Navier-Stokes方程。结果表明：无隔板时,三通内的流动为最常见的类型,支管内存在3个分离区,在转向过程中形成第1分离区,即马蹄涡;随后是第2分离区,一对反向旋转的旋涡,即Dean涡,及三通顶部壁面形成第3分离区。流场沿y=0 mm和z=0 mm平面基本呈对称分布。有隔板时,流场的左右和上下结构均不对称;在隔板和外侧壁面间的角点形成范围较小的驻涡,在支管内形成不稳定的螺旋状分离涡,致使气流振荡,从而使得三通连接和隔板处管壁出现裂纹。根据上述流态设计了管路优化方案和整流装置,优化后能有效减小或消除分离;其中去掉隔板最简单易行,可以解决裂纹的问题。     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

双脉冲固体火箭发动机隔舱打开与破片运动过程模拟

相比传统固体火箭发动机,具有能量管理特性的双脉冲固体火箭发动机结构更为复杂,为了提高其工作可靠性,针对核心部件金属隔舱的破片运动过程开展了数值仿真与试验研究。首先基于LS-DYNA软件,分析中引入监测函数、逻辑开关函数和加载驱动函数,模拟燃气流对破片的连续作用力,计算得到了在不同时刻破片的空间分布规律、撞击点位置及发动机内部损伤情况,保证了破片运动过程的高保真还原。其次,为了验证仿真结果的准确性,进行了模拟二脉冲初始工况的热流试验,发现破片撞击位置及损伤程度的仿真结果与试验数据一致性较高,其中撞击位置的预示误差小于9%,试验结果充分验证了有限元模型的准确性。由此,建立了适用于双脉冲固体火箭发动机金属隔舱破片运动过程的分析模型,实现了破片撞击位置及损伤程度的高精度预示。     

基于气压高度辅助的机载自主完好性监测算法

卫星接收机自主完好性监测是指根据用户接收机的多余观测值监测用户定位结果的完好性,其目的是在导航过程中检测出发生故障的卫星,并保障导航定位精度。针对卫星接收机自主完好性监测算法可用性不足的问题,结合机载实际导航系统配置,提出了一种基于气压高度表辅助的机载自主完好性监测算法。综合利用卫星导航系统及气压高度表观测信息,建立联合系统的观测模型,推导了基于多解分离的完好性监测及保护级别计算方法。仿真结果表明,相比于传统的接收机自主完好性监测算法,该算法在可见星为5颗时仍能识别故障卫星。该算法具有更好的故障检测能力及可用性,能有效提高卫星导航系统的完好性监测性能,从而保证卫星导航系统的精度和可靠性。