Ca的掺入对复合氧化物LaFeO3和LaMnO3的结构及电性的影响

用柠檬酸法、固相法制备了替代的复合氧化物Ｌａ１－ｘＣａｘＦｅＯ３及Ｌａ１－ｘＣａｘＭｎＯ３。对样品进行了ＸＲＤ及导电能力测试。结果表明：Ｘ≤０．５，复合氧化物为单相的钙钛矿结构；Ｃａ的掺入，改善了ＬａＦｅＯ３导电性能，使其室温电阻率从６×１０＾４Ω·ｃｍ降低到１０Ω·ｃｍ左右；而对ＬａＭｎＯ３的影响不大，其室温电阻率在１０＾－１Ω·ｃｍ左右。     

体表电位标测系统中关键技术——心电信号数据高速采集

心电信号的数据采集是体表标测系统中关键技术之一。文中提出了128通道高性能体表标测系统中心电信号数据采集的VxD算法，在Wind9x系统下利用VxD技术、锁定内存和临界资源互斥访问算法相结合，实现了心电数据高速实时采集。该软件充分利用了硬件的等待时间，具有实时性高，运行速度快占内存少的特点。该软件在VtoolsD开发平台上用VisualC＋＋开发。     

Morphology and Frictional Characteristics Under Electrical Currents of Al203/Cu Composites Prepared by Internal Oxidation

Two AhO3/Cu composites containing 0.24 wt.% A1203 and 0.60 wt.% A1203 separately are prepared by internal oxidation.Effectsof sliding speed and pressure on the fi-ictional characteristics of the composites and copper against brass are investigated and compared.The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope (SEM) and energy dispersive X-ray spectrum (EDS).The results show that the wear resistance of the AI203/Cu composites is superior to that of copperunder the same conditions.Under a given electrical current,the wear rate of AI203/Cu composites decreases as the AleO3-content increases.However,the wear rates of the Al203/Cu composites and copper increase as the sliding speed and pressure increase under drysliding condition.The main wear mechanisms for AleO3/Cu composites are of abrasion and adhesion;for copper,it is adhesion,although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.     

基于结构健康监测的飞机结构 MSG-3 分析

结构健康监测(SHM)技术被广泛引入到了飞机设计与维护,本文依据现阶段SHM技术的发展现状,将SHM技术与MSG-3分析思想融合,制定了一种针对采用SHM技术飞机结构的计划维修分析流程。     

三维数模随动下的机翼结构重量优化

目前,基于快速建模下的重量重心估算系统得到了快速发展。为了进一步提高结构重量估算精度,研究了如何在重量重心快速分析(WCGA)系统环境中构建优化模块。以机翼结构重量优化为例,提出优化流程,对优化模块功能进行分解,给出模型简化要求。以A320飞机机翼为例,对梁和长桁进行优化,结果显示,经过优化,有效减轻了结构重量,且相比于传统的减重优化设计方法,极大提高了计算效率。     

Two years of INTEGRAL result on X-ray binaries

INTEGRAL is the ESA lead International Gamma-Ray Astrophysical Laboratory, successfully launched the 17th October 2002 from Baikonur with a Proton vehicle. In view of the high sensitivity of the two γ-ray instruments IBIS and SPI and their capability to provide at the same time image, spectra and time profiles of all the sources in their wide field of view, a key project was approved as “Core Programme” to obtain deep observations of the Galactic Centre (GCDE) and to exploit regular scan of the whole Galaxy Plane since the beginning of the mission. This paper will briefly review the main astrophysical results obtained in the field of high energy Galactic sources with the INTEGRAL/IBIS γ-ray Imager onboard INTEGRAL, and make a comparison with the previous scenario depicted by the BeppoSAX and RXTE results.     

试论科技论文的语言特点

阐述了科技论文在现代社会中的重要地位和作用，着重探讨科技论文的语言特点。在科技论文中使用多语系语言，且除了使用自然语言符号系统以外，同时大量使用超自然语言符号系统。科技论文要求语言简明、精确，逻辑性强，并严格遵守有关的规范和标准；在语法上则多采用存在句、泛指句和析使句，常用第三人称。     

Ni3Al金属间化合物中空位团稳定构型的计算机模拟研究

本文采用分子动力学方法,对金属间化合物Ni3Al中的点缺陷进行了计算机模拟研究,其中原子间相互作用势采用F-S多体势.通过计算Ni3Al中各种构型的空位团的形成能及结合能,进而分析比较各种构型的空位团的稳定性以及热平衡时的数量,总结了Ni3Al中空位的聚集规律.     

时分式平面—立体电视图像转换器

时分式平面－立体电视图像转换器是由视频图像信号处理电路、控制信号产生电路和液晶眼镜驱动电路三部分构成，根据其构成和工作原理，可采用多种具体电路来实现。     

嵌补式网格技术在三维增升装置绕流数值模拟中的应用

基于Jameson的有限体积方法，采用多块网格技术求解Reynolds平均N－S方程组，对三维增升装置绕流进行数值模拟。提出了新颖的嵌补式多块网格技术，使得网格生成和流场计算得到了明显的简化。计算结果与实验数据吻合良好。