An empirical solar radiation pressure model for satellites moving in the orbit-normal mode

We present a family of empirical solar radiation pressure (SRP) models suited for satellites orbiting the Earth in the orbit normal (ON) mode. The proposed ECOM-TB model describes the SRP accelerations in the so-called terminator coordinate system. The choice of the coordinate system and the SRP parametrization is based on theoretical assumptions and on simulation results with a QZS-1-like box-wing model, where the SRP accelerations acting on the solar panels and on the box are assessed separately. The new SRP model takes into account that in ON-mode the incident angle of the solar radiation on the solar panels is not constant like in the yaw-steering (YS) attitude mode. It depends on the elevation angle of the Sun above the satellite’s orbital plane. The resulting SRP vector acts, therefore, not only in the Sun-satellite direction, but has also a component normal to it. Both components are changing as a function of the incident angle. ECOM-TB has been used for precise orbit determination (POD) for QZS-1 and BeiDou2 (BDS2) satellites in medium (MEO) and inclined geosynchronous Earth orbits (IGSO) based on IGS MGEX data from 2014 and 2015. The resulting orbits have been validated with SLR, long-arc orbit fits, orbit misclosures, and by the satellite clock corrections based on the orbits. The validation results confirm that—compared to ECOM2—ECOM-TB significantly (factor 3–4) improves the POD of QZS-1 in ON-mode for orbits with different arc lengths (one, three, and five days). Moderate orbit improvements are achieved for BDS2 MEO satellites—especially if ECOM-TB is supported by pseudo-stochastic pulses (the model is then called ECOM-TBP). For BDS2 IGSOs, ECOM-TB with its 9 SRP parameters appears to be over-parameterized. For use with BDS2 IGSO spacecraft we therefore developed a minimized model version called ECOM-TBMP, which is based on the same axis decomposition as ECOM-TB, but has only 2 SRP parameters and is supported by pseudo-stochastic parameters, as well. This model shows a similar performance as ECOM-TB with short arcs, but an improved performance with (3-day) long-arcs. The new SRP models have been activated in CODE’s IGS MGEX solution in Summer 2018. Like the other ECOM models the ECOM-TB derivatives might be used together with an a priori model.     

高能(450 kV)X射线参考辐射场附加过滤研究

利用MCNP程序对450kV X光机建立模型，计算各参考辐射质下的原级谱、平均光子能量。对ISO 4037-1中已有范围的管电压与附加过滤片厚度关系曲线进行二次拟合，确定模拟厚度范围。利用MCNP计算各附加过滤组合下的平均光子能量值，并与外推法得出的平均光子能量值进行对比，将相对偏差最小时的附加过滤作为最终确定值。从部分能量点的模拟与测量结果的对比可看出，模拟得出的平均光子能量在2%以内与PTB及中国计量院测量结果保持一致，附加过滤最大相对偏差为18%。     

飞机封闭腔室减重降噪优化方法

噪声水平是现代飞机封闭腔室设计的重要指标,设计中单纯地对壁板进行加肋处理虽能显著降低噪声但会大大增加结构质量,为此对由封闭腔室构成的结构-声耦合系统进行了减重降噪优化研究。基于结构-声耦合有限元模型,利用有限元软件ACTRAN计算了频谱加载时舱内的声压响应。通过试验对简化处理及数值计算进行了验证,并修正了相关模型参数。为了降低结构质量,以加强肋为边界对舱门壁板进行了分区,通过对各个区域壁板厚度及肋条截面积的优化设计,使系统动刚度分配更趋合理,降低了声辐射能量以及结构-声腔的耦合性,从而实现了在满足噪声约束条件下减轻结构质量的目标。本文的工作对实际工程中由加肋壁板所构成的类似结构的减重降噪设计有着较好的工程指导价值。     

S弯二元喷管红外辐射特性实验

基于轴对称排气系统设计了一套S弯二元喷管的实验模型,在实验工况下测量了喷管实验件的部分流场参数和远场红外辐射特性,对S弯二元喷管的红外辐射特性进行了分析和研究,并与基准轴对称喷管的红外辐射实验结果进行了对比。结果表明:上方探测平面是S弯二元喷管的主要辐射方向,其最大辐射角度为15°,在该方向角上固体壁面辐射的贡献最大。下方和侧向探测平面各方向角的红外辐射强度明显小于上方探测平面,主要是由于S弯二元喷管遮挡了大部分的内部高温壁面。与基准轴对称喷管对比,S弯二元喷管有着明显的红外抑制作用,在尾部方向S弯二元喷管的积分辐射强度相比轴对称喷管降低了81%,最大辐射强度相比轴对称喷管降低了47%,燃气辐射降低50%。      

三轴承矢量喷管红外辐射特性

针对涡扇发动机用三轴承矢量喷管（3BSN）,通过数值模拟的方法研究了在巡航和垂直起降（VTOL）状态即非矢量和90°矢量状态下三轴承矢量喷管的红外辐射空间分布特征,并分析了其影响机理。结果表明,在非矢量状态下由于特殊的几何型面使得喷管下壁面出现了局部高温区,喷流形状也变成椭圆锥形,造成垂直探测面上正探测角壁面红外辐射较负探测角最大增加44.6%,水平探测面上的燃气红外辐射大于垂直探测面;90°矢量状态下,由于偏转的喷管结构对前端高温部件的遮挡,总辐射峰值仅为非矢量状态的43.3%;喷管90°矢量偏转使得远离曲率中心一侧的气流速度降低温度升高,喷管外侧出现了大范围的局部高温区,导致垂直探测面负探测角范围的壁面辐射大于正探测角范围,最大相对差值达到71.9%。喷管偏转也遮挡了部分喷管内部的高温燃气,垂直探测面负探测角的仅能覆盖喷管出口处的高温燃气区域,明显小于正探测角,造成燃气辐射出现了20%的最大相对差值。     

Convex optimization of asteroid landing trajectories driven by solar radiation pressure

High-area/mass ratio landers driven by Solar Radiation Pressure (SRP) have potential applications for future asteroid landing missions. This paper develops a new convex optimization-based method for planning trajectories driven by SRP. A Minimum Landing Error (MLE) control problem is formulated to enable planning SRP-controlled trajectories with different flight times. It is transformed into Second Order Cone Programming (SOCP) successfully by a series of different convexification technologies. A trust region constraint and a modified MLE objective function are used to guarantee the convergence performance of the optimization algorithm. Thereafter, the SRP-driven trajectory optimal control problem is converted equivalently into a sequence of convex optimal control problems that can be solved effectively. A set of numerical simulation results has verified the effectiveness and feasibility of the proposed optimization method.     

高频噪声场中薄壁结构响应的预估

本文用统计能量分析(StatisticalEnergyAnalysis简称SEA)法研究了在高频宽带随机噪声场中板及加筋板(航空航天器用蒙皮)的加速度响应。发现,在高频段同样外场激励情况下,加筋板的响应大于光板的。本文解释了这一用质量定理无法解释的现象,并用叠加法确定了复杂结构加筋板的模态密度、辐射阻抗和输入功率。     

非地球同步卫星相对于太阳的几何关系

给出确定非地球同步卫星轨道的日照边界点在天球上投影的位置、太阳光在卫星及其携带仪器各个平面上的投射角以及星载红外分光计内部冷黑体被太阳照射到的轨道部份和概率的计算公式。最后以极轨气象卫星上的红外分光计为例进行了计算。其结果可以提供给分光计某些部份的设计以及极轨气象卫星发射时间的选择作参考。     

空间辐射器热分析

在航天飞机温控系统中,空间辐射器是最主要部件。对以航天飞机蒙皮为辐射表面的,单面翼—管式空间辐射器进行了详细的热分析,把平均翼效率代替局部翼效率,利用有限差分的方法对单面翼—管式辐射器进行了性能计算。     

组合光学太阳反射镜的热辐射性能测量

用量热计法测量了通信广播卫星上用的光学太阳反射镜（ＯＳＲ）的太阳吸收比αｓ和半球发射率εＨ。为了准确计算卫星的温度分布,测量的是组合ＯＳＲ样品的热辐射性能。作为对比,同时还用量热计法和光谱法测量了单片ＯＳＲ的太阳吸收比,并且对各个测量结果及其差异进行了分析。分析表明,不应当将单片ＯＳＲ的法向太阳吸收比αｓ作为设计参数,否则将在温度计算中引起较大误差。