扩散连接界面缺陷对Ti-6Al-4V合金力学性能的影响

研究了φ4mm与φ2mm的扩散连接界面缺陷对Ti-6Al-4V合金力学性能的影响。当拉伸载荷方向与缺陷平面平行时,材料的强度与塑性与无缺陷材料相当,这是由于此类缺陷对样品受力截面的面积几乎没有影响。含有φ4mm缺陷试样的拉压疲劳寿命展现出很大的分散性,界面缺陷并未成为裂纹萌生的唯一位置。从表面起裂的样品均处于高寿命区域,而绝大部分从缺陷处起裂的样品均落于低寿命区域。有限元分析表明,当缺陷位于中心位置时其引起的应力集中较小,应力分布梯度较小;缺陷位于边缘位置时,应力集中效应增大。     

不同冶炼工艺对1Cr18Ni10Ti钢夹杂物的影响

通过试验研究了1Cr18Ni10Ti不锈钢的4种冶炼工艺:真空感应+电渣重熔、真空感应(陶瓷过滤器)、真空感应(陶瓷过滤器)+电渣重熔、真空感应+真空自耗,得到钢锭中夹杂物的种类、大小以及数量的变化.对比试验结果可知,采用真空感应(陶瓷过滤器)冶炼工艺与真空感应+真空自耗之后的钢锭的夹杂物水平相当,D类夹杂物数量最少,大颗粒夹杂物占比也最小.     

基于三维裂纹尖端应力场的应力强度因子计算方法

提出一种基于无限大体裂纹尖端弹性应力场理论解的前几项多项式函数,对实际裂纹体弹性应力场有限元解进行拟合来计算应力强度因子的方法.该方法在计算应力强度因子时不需要预先假设裂纹尖端的应力应变状态,应力强度因子计算结果更符合三维裂纹体裂纹尖端实际的应力应变状态.首先基于二维无限大板中心穿透裂纹应力场理论解验证了方法的有效性,探讨了拟合确定应力强度因子需要的多项式应力函数的项数.然后分别以二维大板中心穿透裂纹、三维大体内埋圆裂纹和三维有限厚板中心穿透裂纹的应力强度因子计算为例,通过与无限大板和无限大体应力强度因子理论解以及基于位移外推法和1/4节点张开位移法的应力强度因子有限元解的对比分析,验证了该方法的有效性和合理性.研究表明该方法能够合理反映三维裂纹体裂纹尖端的实际应力应变状态,计算得到的应力强度因子数值更合理.      

嫦娥一号卫星星地时差校正量计算方法研究

影响月球探测卫星星地时差的因素较多，文章介绍了其计算模型，并对其中的模糊距离进行了详细分析。通过对试验数据的分析，运用最小二乘法，分别建立了集中校时量和均匀校时量计算模型。实际结果表明：运用此两种校时模型和方法可以方便有效地控制嫦娥一号卫星的星地时差，并使其在一段时期内保持在5ms范围以内。     

环境减灾-1A、1B卫星光学载荷在轨运行情况分析

环境减灾-1A、1B卫星于2008年9月6日发射升空,至2013年7月20日,2颗卫星的4台宽覆盖多光谱CCD相机、1台超光谱成像仪(HSI)和1台红外相机(IRS)已在轨稳定工作近5年,共获取超过61万景2级地面遥感图像数据。文章对在轨运行的光学载荷遥测参数进行了统计和分析,结果表明:DC/DC电压遥测变化量不超过5%,关键光机部位温度遥测变化量小于2.25℃,转动部件电压和电流遥测变化量小于1%,遥测参数均在设计范围内,显示光学载荷在轨稳定正常工作。最后,综合分析了光学载荷图像数据应用情况,分析表明:光学载荷图像数据具有较强的地物影像分类、提取和分辨能力,与国外同类卫星比较,水体识别符合度达到90%以上,旱情分级符合度大于66%,光谱分辨率达到5nm,积雪范围提取精度达到90%以上,在各类应用领域发挥了较大的效能。     

嫦娥一号卫星数据高可靠性保护设计

针对我国第一个月球探测器的特点，对星载网络数据保护做了专门的设计。文章着重介绍了嫦蛾一号卫星星载数据高可靠性保护的设计方案与具体实现情况。     

Effects of TADs on the F region of the mid-latitude ionosphere during an intense geomagnetic storm

Based on observations of two ionosondes at Wuhan and Kokubunji, this paper presents effects of TADs on the daytime mid-latitude ionosphere during the intense geomagnetic storm on March 31, 2001. During a positive ionospheric storm, the start of the enhancement of the foF2 (F2 peak plasma frequency) at Wuhan lags that at Kokubunji by 15 min, which corresponds to the time interval of traveling atmospheric disturbances (TADs’) propagation from Kokubunji to Wuhan. Associated with the uplifting of the hmF2 (height of F2 peak) caused by TADs, it is observed by the two ionosondes that the F1 cusp becomes better developed. Therefore, during a geomagnetic storm, TADs originating from the auroral oval may have a strong influence on the shape of the electron density profile in the F1 region ionosphere at middle latitudes. It is highly likely that TADs are responsible for the evolution of the F1 cusp.     

Attitude control system design and on-orbit performance analysis of nano-satellite––‘‘Tian Tuo 1’’

‘‘Tian Tuo 1'(TT-1) nano-satellite is the first single-board nano-satellite that was successfully launched in China. The main objective of TT-1 is technology demonstration and scientific measurements. The satellite carries out the significant exploration of single-board architecture feasibility validation, and it is tailored to the low-cost philosophy by adopting numerous commercialoff-the-shelf(COTS) components. The satellite is featured with three-axis stabilization control capability. A pitch bias momentum wheel and three magnetic coils are adopted as control actuators.The sun sensors, magnetometers and a three-axis gyro are employed as the measurement sensors.The quaternion estimator(QUEST) and unscented Kalman filter(UKF) method are adopted for the nano-satellite attitude determination. On-orbit data received by ground station is conducted to analysis the performance of attitude determination and control system(ADCS). The results show that the design of ADCS for TT-1 is suitable, robust and feasible.