高超声速边界层转捩特性试验探究

通过在激波风洞中开展转捩试验,选取来流马赫数分别为6和8,单位雷诺数分别为4.1×10 6m -1 、2.6×10 7m -1 和4.4×10 7m -1 的来流条件,研究马赫数、单位雷诺数以及攻角变化对钝锥边界层和平板边界层转捩位置的影响。结果表明,攻角增大使钝锥迎风面和背风面边界层转捩位置均前移,使平板边界层转捩位置也前移;钝锥边界层在低马赫数时更容易转捩,平板边界层转捩受马赫数影响在攻角有差异时有所不同;单位雷诺数的增大促进转捩,但对于钝锥边界层而言,该参数增加到试验选定的上限时,转捩位置的变化并不明显;在转捩过程中平板边界层的脉动压力系数与热流具有相同的变化趋势。试验捕捉到了第二模态扰动。     

An analysis and enhanced proposal of atmospheric boundary layer wind modelling techniques for automation of air traffic management

The air traffic management automation imposes stringent requirements on the weather models, in such a way that they should be able to provide reliable short-time forecasts in digital formats in almost real time. The atmospheric boundary layer is one of the regions where aircraft operation and coordination are critical and therefore atmospheric model performance is also vital. This paper presents conventional and innovative techniques to improve the accuracy in the forecasting of winds in the lower atmospheric layer, proposing mechanisms to develop better models including deterministic and stochastic simulations. Accuracy is improved by optimizing the grid, assimilating observations in cycling simulations and managing a number of ensemble members. An operation-driven post-processing stage helps to incorporate detailed terrain definitions and real-time observations without re-running the model. The improvements are checked against mesoscale weather simulations at different scales and a dedicated flight campaign. The results show good performance of the model without sensitively increasing the required throughput.     

低雷诺数下跨声速转子流动失稳及周向槽处理机匣扩稳

采用数值方法模拟了低雷诺数条件下NASA Rotor 37跨声速压气机转子内部流场。结果表明,附面层径向涡是该压气机转子流动失稳的一个很重要的原因。根据该压气机转子低雷诺数条件下流动失稳的特点,研究了周向槽处理机匣结构对其性能的影响。结果表明,引入处理机匣后,附面层径向涡得到一定程度的抑制,由附面层径向涡所引发的叶顶阻塞区有所减小,提高了压气机转子的失速裕度。     

S-A模型在分离流动模拟中的改进

基于湍流不平衡性的分析,通过修正雷诺应力以及模型系数的计算,提高了S-A模型在二维边界层以及三维叶栅的分离流动上的预估能力。修正后的S-A模型给出了与实验吻合较好的结果,在对于分离流动的预估能力上优于原始模型。     

高压离心压气机导叶流场的附面层抽吸控制研究

通过数值模拟研究了某小型涡扇发动机离心压气机的出口导叶流场特点,结合拓扑分析方法讨论了附面层抽吸对叶栅性能的影响。结果表明:原型叶栅由于展弦比较小,流动空间狭窄,各种形式的附面层分离相互掺混,恶化了整个叶栅的流动。通过附面层抽吸可以改变叶栅内的分离结构,明显减小吸力面的分离,使得流场结构趋于简单,从而减小损失、提高叶栅效率。     

A linear stability analysis of large-Prandtl-number thermocapillary liquid bridges

A linear stability analysis is applied to determine the onset of oscillatory thermocapillary convection in cylindrical liquid bridges of large Prandtl numbers (4  Pr  50). We focus on the relationships between the critical Reynolds number Re_c, the azimuthal wave number m, the aspect ratio Γ and the Prandtl number Pr. A detailed Re_c–Pr stability diagram is given for liquid bridges with various Γ. In the region of Pr > 1, which has been less studied previously and where Re_c has been usually believed to decrease with the increase of Pr, we found Re_c exhibits an early increase for liquid bridges with Γ around one. From the computed surface temperature gradient, it is concluded that the boundary layers developed at both solid ends of liquid bridges strengthen the stability of basic axisymmetric thermocapillary convection at large Prandtl number, and that the stability property of the basic flow is determined by the “effective” part of liquid bridge.     

非设计状态下尾迹输运对高负荷低压涡轮附面层的影响

为了研究非设计状态下的上游尾迹在叶栅通道内的形态演化与发展,分析尾迹与叶片吸力面附面层的相互作用,基于高负荷低压涡轮(LPT)叶型Packb对非设计状态下尾迹输运进行了研究。研究主要通过数值模拟的方法进行,使用CFX软件,利用LES模型耦合Smagorinsky亚格子模型。讨论了非定常来流0°和+10°攻角工况下,尾迹与吸力面附面层相互作用的差异。分析发现,+10°攻角工况时,尾迹对附面层转捩的促进作用较0°攻角工况时更为显著;+10°攻角工况时,尾迹与附面层的相互作用时间更长,尾迹诱导转捩的起始位置更靠上游。     

碳氢燃料热声不稳定流动特性和边界实验分析

为保障空-油换热器安全稳定运行,对竖直上升圆管内超临界压力航空燃料的热声不稳定流动进行了实验研究。阐述了管壁温度的振荡特征和热声不稳定流动的诱发原因。考察了运行参数对流动稳定工况和流动不稳定工况界限的影响。取相邻流动稳定工况和流动不稳定工况的热流密度平均值作为边界,分析了该边界随进口拟过冷度的变化情况。通过临界拟相变数和拟过冷度数的比值表征,建立了热声不稳定流动边界与进口雷诺数和相对压力关联的预测准则。结果表明:拟沸腾效应导致了热声不稳定流动现象。进口温度和运行压力越低,热声不稳定流动越容易出现。提出的边界预测准则具有较高的精度,与实验结果的相对偏差在±15%以内。     

Experimental characteristics of oblique shock train upstream propagation

The structure and dynamics of an oblique shock train in a duct model are investigated experimentally in a hypersonic wind tunnel. Measurements of the pressure distribution in front of and across the oblique shock train have been taken and the dynamics of upstream propagation of the oblique shock train have been analyzed from the synchronized schlieren imaging with the dynamic pressure measurements. The formation and propagation of the oblique shock train are ini-tiated by the throttling device at the downstream end of the duct model. Multiple reflected shocks, expansion fans and separated flow bubbles exist in the unthrottled flow, causing three adverse-pressure-gradient phases and three favorable-pressure-gradient phases upstream the oblique shock train. The leading edge of the oblique shock train propagates upstream, and translates to be asym-metric with the increase of backpressure. The upstream propagation rate of the oblique shock train increases rapidly when the leading edge of the oblique shock train encounters the separation bubble near the shock reflection point and the adverse-pressure-gradient phase, while the oblique shock train slow movement when the leading edge of the oblique shock train is in the favorable-pressure-gradient phase for unthrottled flow. The asymmetric flow pattern and oscillatory nature of the oblique shock train are observed throughout the whole upstream propagation process.     

Influence of coupled boundary layer suction and bowed blade on flow field and performance of a diffusion cascade

Based on the investigation of mid-span local boundary layer suction and positive bowed cascade, a coupled local tailored boundary layer suction and positive bowed blade method is developed to improve the performance of a highly loaded diffusion cascade with less suction slot. The effectiveness of the coupled method under different inlet boundary layers is also investigated.Results show that mid-span local boundary layer suction can effectively remove trailing edge separation, but deteriorate the flow fields near the endwall. The positive bowed cascade is beneficial for reducing open corner separation, but is detrimental to mid-span flow fields. The coupled method can further improve the performance and flow field of the cascade. The mid-span trailing edge separation and open corner separation are eliminated. Compared with linear cascade with suction, the coupled method reduces overall loss of the cascade by 31.4% at most. The mid-span loss of the cascade decreases as the suction coefficient increases, but increases as bow angle increases. The endwall loss increases as the suction coefficient increases. By contrast, the endwall loss decreases significantly as the bow angle increases. The endwall loss of coupled controlled cascade is higher than that of bowed cascade with the same bow angle because of the spanwise inverse ‘‘C" shaped static pressure distribution. Under different inlet boundary layer conditions, the coupled method can also improve the cascade effectively.