绕圆头回转体通气空化流型的实验研究

为了深入了解通气空化流动现象,利用高速全流场显示技术,对绕圆头回转体通气空化流型进行实验研究。结果表明,重力效应和通气量对通气空化的多相流流型起主要作用。定义了弗洛德数和通气率两个无量纲数,将绕圆头回转体通气空化分为5种多相流流型,即透明空泡、透明气弹、透明分层、水气混合以及半透明水气混合。流动参数对流型的影响分为2个阶段,即重力起主要作用阶段和重力效应不明显阶段。在重力起主要作用阶段,通气率一定时,随着弗洛德数的增大,附着弹体的空泡倾斜程度变小,弹体上表面的断裂空泡转变为贴着弹体壁面的稳定空泡;弗洛德数一定时,随着通气率的增大弹体上表面断裂空泡的尺度不断增大。在重力效应不明显阶段,通气率一定时,随着弗洛德数的增大,雷诺数变大,流场的湍流强度增大,空泡尾流区域水气交换的程度加剧;弗洛德数一定时,随着通气率的增大,通气空化数减小,绕弹体的云雾状空泡逐渐转变为透明空泡。最后,进一步分析了重力影响下透明空泡脱落的非定常过程,以及反向射流作用下云雾状空泡交替脱落的非定常过程。     

翼型尾缘低频大功率合成射流的动态载荷特性研究——B：动态气动载荷特性分析

针对NACA0015翼型,设计了适用于风洞研究的尾缘低频大功率合成射流致动器,对翼型尾缘合成射流作用下的非定常气动特性进行了风洞实验研究。研究表明：尾缘合成射流与横流的相互作用能够有效改变作用在翼型上的气动载荷;单侧喷口喷/吸时,喷冲程气动力系数响应幅值约为吸冲程幅值的3倍;双侧喷口同时工作时,升力和力矩系数的幅值并不是单侧喷口单独工作时喷气幅值的简单叠加,而是处于单侧喷气幅值和喷吸幅值和之间;升力和力矩响应的幅值与喷流动量系数的平方根之间存在近似的线性关系;在动量系数不变时,升力和力矩系数响应的幅值会随减缩频率的增加而减小;给定合成射流器行程,升力和力矩响应幅值与合成射流频率之间近似呈线性关系。     

冲击射流的彩虹纹影实验研究

超声速冲击射流在短距、垂直起降飞行器（S/VTOL）以及火箭发射等方面应用广泛,但是伴随着流场与噪声等诸多方面的问题。要研究这一类问题,必先研究这一类超声速流动的波系结构。文章利用彩虹纹影测量系统,对不同距离不同压比的冲击射流进行实验研究,得到了清晰的彩虹纹影实验结果,细致地呈现了冲击射流的波系结构。基于实验结果,对三种不同结构的冲击射流的波系结构进行了详细分析。发现喷嘴与挡板距离较大时,形成的射流结构与自由射流相似,壁面附近的射流区域不明显。随着距离减小,冲击射流出现壁面冲击区附近射流比较剧烈的现象。距离进一步减小时,出现滞止泡等结构,滞止泡的形状与压比相关。此外,实验表明冲击射流形成的马赫盘大小、形状与来流压比相关。     

基于PIV的凝胶模拟液撞击雾化速度场实验研究

为了更好研究凝胶推进剂的雾化,采用时间分辨粒子图像测速(TR-PIV),研究了不同撞击角度(45°,60°,75°,90°和120°)和射流压差(0.4MPa~0.8MPa)对凝胶推进剂雾化速度的影响。实验结果表明:雾化液滴速度对于撞击轴线呈单峰对称分布,距离撞击点越远,雾化液滴速度越小且分布越均匀;增大撞击角和增大射流压差都可提高凝胶推进剂有效撞击速度,即增加撞击后液体动能转换液体破碎所需的能量,雾化质量提高;当有效撞击速度大于27.9m/s时,实验室配置的凝胶推进剂可充分雾化。     

镁合金在空空导弹导引头上应用可行性研究

对空空导弹导引头上镁合金材料的选用、加工、表面处理、结构装配、盐雾试验等方面进行了研究。首先在目前应用较为广泛的镁合金材料牌号中选取了适合导引头结构应用的MB15来代替目前应用的铝合金材料,并选取导引头中具有代表性的薄壁、高精度试验件进行了加工试制;其次对试制试验件选取不同的表面处理方法进行表面处理,通过装配、盐雾试验来验证其表面处理的防腐蚀能力;最后给出了在空空导弹导引头上应用镁合金的合理建议。     

自由射流中飞机进气道前方亚声速流场数值仿真研究

为了预测航空发动机高空模拟自由射流试验中飞机进气道-发动机组合体前方的亚声速流场特性,优化试验舱的气动设计,采用 CFD 方法在亚声速自由射流和真实大气飞行条件下对某战斗机进气道的外流场进行数值模拟。分析了进气道对前方气流压缩作用与飞行马赫数关系,对比和分析了分别在自由射流与真实大气中进气道前和进气道入口处的马赫数分布,确定了3种马赫数下进气道在自由射流中的最佳安装位置。比较发现,亚声速自由射流对真实高空大气飞行进行模拟,可以得到马赫数相似的流场。     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.     

Coupled Lagrangian impingement spray model for doublet impinging injectors under liquid rocket engine operating conditions

To predict the effect of the liquid rocket engine combustion chamber conditions on the impingement spray, the conventional uncoupled spray model for impinging injectors is extended by considering the coupling of the jet impingement process and the ambient gas field. The new coupled model consists of the plain-orifice sub-model, the jet-jet impingement sub-model and the droplet collision sub-model. The parameters of the child droplet are determined with the jet-jet impingement sub-model using correlations about the liquid jet parameters and the chamber conditions.The overall model is benchmarked under various impingement angles, jet momentum and offcenter ratios. Agreement with the published experimental data validates the ability of the model to predict the key spray characteristics, such as the mass flux and mixture ratio distributions in quiescent air. Besides, impinging sprays under changing ambient pressure and non-uniform gas flow are investigated to explore the effect of liquid rocket engine chamber conditions. First, a transient impingement spray during engine start-up phase is simulated with prescribed pressure profile. The minimum average droplet diameter is achieved when the orifices work in cavitation state, and is about 30% smaller than the steady single phase state. Second, the effect of non-uniform gas flow produces off-center impingement and the rotated spray fan by 38°. The proposed model suggests more reasonable impingement spray characteristics than the uncoupled one and can be used as the first step in the complex simulation of coupling impingement spray and combustion in liquid rocket engines.     

EXPERIMENTAL STUDY OF FLOW FIELDS IN THE VICINITY OF A FILM COOLING HOLE EXIT

Sofar,filmcoolingisextensivelyadoptedforprotectinghightemperaturepartsingasturbine.Manyresearchworksarefocusedonflow[1~3Jandheattransfer[4'5jinthedownstreamofthecircularhole,buttheflowcharacteristicsattheholeexit,especiallyforflaredholeexit,arenotreportedatpresent.Inordertodesignasuitab1eholeshapeforpracticalcoolingandprovideplentyexperimentaldataforverificationofcomputercodes,adetai1edexperimentalin-vestigationabout3-Dflowfieldsattheexitofasinglecircularandfan-shapedholehasbeencompleted.1Exp…     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。