M46J高模量碳纤维预浸QY8911纤维束性能研究

以航空发动机应用为背景，研究了M46J／QY8911缠绕复合材料的预浸纱制备方法及性能，根据M46J特性，对现有的GB3326中纤维束力学性能测试试样的加强方式进行了改进，制作了M46J浸渍QY8911树脂的纤维束试样并测试其力学性能，同时与M46J浸渍环氧树脂的纤维束的力学性能进行比较，研究表明，不同树脂特性，不同固化工艺以及制造中所施加的张力都会影响到纤维束的纤维利用率。     

低频电连接器检测方法研究CSCD

本文主要阐述了低频电连接器外观检测和电性能测试中的接触电阻、绝缘电阻和介质耐电压的检测方法及其注意事项,提出为满足武器系统对低频电连接器耐恶劣环境、高可靠的特殊需求,有效保证武器型号系统中电连接器的质量,必须规范低频电连接器外观及电性能指标检测标准。本文可为从事低频电连接器检测工作的人员提供参考。     

A novel surrogate modeling strategy of the mechanical properties of 3D braided composites

In this paper, a surrogate-based modeling methodology is developed and presented to predict the elastic properties of three dimensional (3D) four-directional braided composites. Using this approach, the prediction process becomes feasible with only a limited number of training points. The surrogate models constructed using Finite Element (FE) method and Diffuse Approximation, reduce the computational time and cost for preparing experimental samples. In the FE model, multiscale method is applied to couple the computations of elastic properties at microscale and mesoscale. Subsequently, a parametric study is performed to analyze the effects of the three design parameters on the elastic properties. Satisfactory results are obtained via the surrogate-based modeling predictions, which are compared with the experimental measurements. Moreover, the predictions obtained from surrogate models concur well with the FE predictions. This study orients a new direction for predicting the mechanical properties based on surrogate models which can effectively reduce the sample preparation cost and computational efforts.     

Effects of process parameters on mechanical properties of abrasive-assisted electroformed nickel

A cathode mandrel with translational and rotational motion, which was supposed to obtain uniform friction effect on surface, was employed in abrasive-assisted electroforming for revolving parts with complex profile. The effects of current density, translational speed and rotational speed on the deposit properties were studied by orthogonal test. The tensile strength, elongation and micro hardness value were measured to find out how the factors affected the properties. The optimized results show that changes of current density affect the tensile strength of nickel layer most, while translational speed has the most remarkable influences on both elonga-tion and micro hardness. The low rotational speed affects the properties least. In this experiment, a smooth nickel layer with tensile strength 581 MPa, elongation 17%and micro hardness 248HV is obtained by the orthogonal test.     

PIP工艺制备SiC晶须增强SiCf/SiC复合材料的性能

以不同界面层厚度的SiC纤维为增强相,采用先驱体浸渍裂解工艺(PIP)制备SiC_f(PyC)/SiC复合材料,并在复合材料基体中引入SiC晶须,对其性能进行研究。结果表明:热解碳(PyC)界面层厚度约为230 nm时,SiC纤维拔出明显,SiC_f/SiC复合材料拉伸强度、弯曲强度和断裂韧度分别达到192.3 MPa、446.9 MPa和11.4 MPa?m^1/2;在SiC_f/SiC复合材料基体中引入SiC晶须后,晶须的拔出、桥连及裂纹偏转等增韧机制增加了裂纹在基体中传递时的能量消耗,使复合材料的断裂韧度和弯曲强度分别提高了22.9%和9.1%。     

MD-130 胶黏剂固化工艺及空间适用性研究

为满足航天电子产品的工艺实施和空间服役要求,本文详细开展了MD-130胶黏剂的固化工艺及空间适应性研究。结果表明,在150℃等温固化60 min后其拉伸剪切强度达到18 MPa,表明其为优选的固化工艺。高低温环境冲击和低剂量的粒子辐照后胶黏剂固化反应更加充分,其芯片剪切强度提高,而大剂量辐照致使高分子降解现象明显,造成了胶接强度的降低。经环境试验后,MD-130胶黏剂仍具有良好的力学性能,满足设计使用要求。     

热处理对FeCo-2V-0.5Cr软磁合金力学与磁学性能的影响

针对FeCo-2V-0.5Cr软磁合金,研究了真空热处理时间对其微观组织结构、力学与磁学性能的影响规律,发现在800℃下热处理时间为2h左右时,合金的抗拉强度和延伸率达到最佳,同时仍保持良好的软磁性能,抗拉强度、延伸率以及矫顽力分别为867.8MPa、10.4%以及2.0Oe。进一步对该合金进行附加磁场下的真空热处理,重点研究了合金的交流损耗与矫顽力随附加磁场方式包括磁场撤除温度与磁场下保温时间的变化规律,发现适当的磁场热处理对合金相关力学性能影响不大,但由于合金中产生了单轴各向异性而使合金矫顽力进一步降至1.6Oe。     

WC/C复合涂层海水环境的耐蚀性与摩擦性能

采用非平衡磁控溅射技术在304L不锈钢和单晶硅基底上沉积WC/C多层复合涂层,利用扫描电镜、Raman光谱仪、X射线衍射仪等研究WC/C复合涂层的微观结构,采用纳米压痕仪、划痕测试系统测试涂层的力学性能,利用电化学测试系统和摩擦磨损试验机分别研究涂层在人工配置的海水环境的耐蚀性能和摩擦性能。结果表明:WC/C复合涂层内含有较多类石墨sp2键结构,存在WC1-x相并镶嵌在非晶碳基质中。较之于304L不锈钢基底,WC/C复合涂层在海水环境中表现出更好的耐蚀性与更优异的摩擦适应性。     

基于labview的冷弯型钢机组力学性能测量系统

根据冷弯型钢机组的实际条件,利用传感器电测法来测量冷弯型钢机组的力能参数系统,以建立对机组的轧制力、主轴扭矩及转速的实时状态监控.同时实现机组运行时轧制力、主轴扭矩及转速这三部分力能信息的显示和存储,以供调出分析系统性能之用,甚至可以用来进行机械的故障诊断.将物理信号转化为电信号利于传输和数据处理,与虚拟仪器的软件部分...     

冷坩埚定向凝固TiAl基合金高温持久性能研究

采用电磁冷坩埚定向凝固技术制备了成分为Ti-47A1-2Cr-2Nb的合金铸锭,定向凝固后的显微组织为α2+γ全片层结构.在0.4～1.2mm/min的抽拉速率范围内,随着抽拉速率的增加,片层间距减小,柱状晶与生长方向的夹角增大.随着温度升高,合金的拉伸强度有所下降,但由于细化片层界面对切变应力变形的阻碍作用,合金的高温拉伸强度会随着抽拉速率的增加而提高.通过对抽拉速率为1.0mm/min试样的拉伸强度与温度的拟合,得到了拉伸强度和温度之间的函数关系.随着抽拉速率的增加,Ti-47A1-2Cr-2Nb合金的持久寿命明显升高,对于抽拉速率为1.2mm/min试样的持久性能测试表明,其持久寿命最长,达到了48h.持久试样的断口形貌表明,其断裂的主要方式是伴随着少量延性断裂的脆性解理断裂.最后根据时间-温度模型,分别采用Larson-Miller和Manson-Haferd参数法建立了定向凝固Ti-47Al-2Cr-2Nb合金的持久强度预测函数模型,预测的理论值与试验结果吻合度较高.