激光加工气膜孔对定向凝固高温合金薄壁持久性能的影响

采用定向凝固无余量精铸工艺制造的接近于空心涡轮叶片形状和壁厚的管状薄壁（δ＝１．２ｍｍ）试样，研究了激光加工孔对定向凝固高温合金薄壁持久性能的影响。结果表明，在９００℃／３７０ＭＰａ下，与没有孔的薄壁试样相比，有一排孔的试样持久性能没有明显降低，有两排孔的试样持久寿命略有下降。显微分析表明，激光加工孔对组织没有明显的影响，只是稍微减小了承载面积，而且只有在出现两排激光孔时才有所表现。     

Integrity of sulfur concrete subjected to simulated lunar temperature cycles

In view of potential application as a construction material on the lunar surface the mechanical integrity of sulfur concrete was evaluated after being subjected to simulated temperature cycles. Here, small cubes of sulfur concrete were repeatedly cycled between room (20 °C) and liquid nitrogen (−191 °C) temperatures after which they, and non-cycled cubes, were evaluated by compression testing. The compression strength of the non-cycled samples averaged ∼35 MPa (5076 psi) before failing whereas the cycled samples fractured at about 7 MPa (1015 psi). Microscopic examination of the fracture surfaces from the cycled samples showed clear de-bonding of the sulfur from the aggregate whereas it was seen adhering in those non-cycled. Based on a simple analysis it was concluded that the large strength discrepancy between cycled and non-cycled samples is due to differences between the coefficients of thermal expansion of the materials constituting the concrete.     

温度翘曲应力对机场刚性道面寿命的影响

分析了目前中国民航机场刚性道面的设计过程,指出在设计过程中忽视温度应力的影响不合理。参照公路水泥混凝土路面温度应力计算方法并根据Miner定律研究了温度翘曲疲劳损耗对于机场刚性道面影响规律,即温度翘曲疲劳损耗随板厚、地基反应模量的增大而增大,随着混凝土设计强度的增加而降低。然后提出采用设计寿命的影响因子nt/Nt评价温度翘曲疲劳损耗对于机场刚性道面设计寿命影响的方法并提供了相应的机场刚性道面板厚度设计流程图。最后提供了一个考虑温度翘曲应力的刚性道面设计实例,为工程应用提供参考。     

运载火箭尾段防热/承载一体化热防护系统设计及性能分析

先进热防护技术是可重复使用运载火箭研制的关键技术之一,具有高结构效率的防热/承载一体化热防护系统是运载火箭极具潜力的备选热防护方案。本文系统地总结了可重复使用运载火箭尾舱段防热和承载两方面的设计要求,设计了一种全复合材料防隔热/承载一体化热防护系统。开展了运载火箭尾段一体化热防护系统设计,进行了代表性单胞结构的高温环境地面试验,揭示了复合材料一体化热防护系统的防隔热机理。同时施加力学和热流载荷,利用有限元方法对运载火箭尾段进行了热力耦合分析,获得了尾段结构的温度场、应变场和应力场。结果表明:在典型载荷工况下一体化热防护系统内壁温度保持在89.2℃以下,内部最大应力不超过9.53 MPa,安全系数达到1.89。     

点击化学在三唑固化体系及固体推进剂中的研究进展

综述了基于GAP的三唑交联固化体系、基于惰性聚醚和聚酯的三唑交联固化体系,指出三唑交联固化体系在高能低特征信号固体推进剂中具有良好的应用前景。分析认为,GAP主链上承载原子的质量分数偏低,且侧链上三唑环的刚性结构及其在GAP主链上的随意分布是基于GAP的三唑交联弹性体力学性能不佳的原因。指出开发兼具优异力学性能和较高能量的三唑交联固化体系将是今后努力的方向。     

气动力/热与结构多场耦合试验模型方案初步设计

以多渠道、多机制交叉耦合为热防护结构特点的新一代高超声速飞行器必须采用气动力/热与结构多场耦合计算方法进行研究。目前,国外已建立较完善的耦合分析系统并用于飞行器研制,国内的中国空气动力研究与发展中心(CARDC)也已自主研发了热环境/热响应耦合计算平台(FL-CAPTER)。为验证多场耦合计算平台所用方法的有效性和计算结果的准确性,设计并开展气动力/热与结构耦合的地面试验具有十分重要的意义。本文结合气动力/热与结构多场耦合试验设计需求,以现有材料和设备能力为依托,开展了试验风洞选取、模型尺寸估算、模型材料选择、模型气动设计与模型结构设计工作。初步研究表明,模型支撑结构附近迎风面局部高温热膨胀将有利于模型前体结构产生可观的整体变形量。本文以此设计了带压缩拐角的二级压缩面结构模型,通过短时间不锈钢模型验证试验和计算对比分析初步验证了模型设计的可行性,并以此为基础预测了高温合金模型的试验结果。为下一步开展高温合金长时间风洞试验奠定了技术基础。     

舱段结构热振耦合环境下仿真分析

针对武器装备对环境适应性要求不断提高的现状,以某舱段结构为研究对象,基于高加速应力筛选试验(HASS)条件,研究了结构在温变-振动耦合环境下的失效机理。首先,结合HASS试验剖面,确定了载荷条件,建立有限元模型;其次,采用ANSYS Workbench软件分析得到结构温度场分布及应力响应,确定了结构危险位置,并对其疲劳寿命进行计算分析,为舱段结构的失效分析及HASS试验剖面的合理制定提供依据和指导。     

An equivalent ground thermal test method for single-phase fluid loop space radiator

Thermal vacuum test is widely used for the ground validation of spacecraft thermal control system. However, the conduction and convection can be simulated in normal ground pressure environment completely. By the employment of pumped fluid loops’ thermal control technology on spacecraft, conduction and convection become the main heat transfer behavior between radiator and inside cabin. As long as the heat transfer behavior between radiator and outer space can be equivalently simulated in normal pressure, the thermal vacuum test can be substituted by the normal ground pressure thermal test. In this paper, an equivalent normal pressure thermal test method for the spacecraft single-phase fluid loop radiator is proposed. The heat radiation between radiator and outer space has been equivalently simulated by combination of a group of refrigerators and thermal electrical cooler(TEC) array. By adjusting the heat rejection of each device, the relationship between heat flux and surface temperature of the radiator can be maintained. To verify this method,a validating system has been built up and the experiments have been carried out. The results indicate that the proposed equivalent ground thermal test method can simulate the heat rejection performance of radiator correctly and the temperature error between in-orbit theory value and experiment result of the radiator is less than 0.5 C, except for the equipment startup period. This provides a potential method for the thermal test of space systems especially for extra-large spacecraft which employs single-phase fluid loop radiator as thermal control approach.     

7150铝合金热变形行为及微观组织

采用Gleeble热模拟机进行热压缩实验,研究7150铝合金在变形温度为300~450℃、应变速率为0.01~10s-1条件下的变形行为,采用Zener-Hollomon参数法构建合金高温塑性变形本构方程,并对变形后的微观组织进行分析。研究表明:7150铝合金的流变应力随应变速率增大而增大,随变形温度增大而降低。该合金热压缩变形的流变应力行为可用双曲正弦形式的本构方程描述,其参数A为4.161×1014s-1,α为0.01956 MPa-1,n为5.14336,热变形激活能Q为229.7531k J/mol。随着温度升高和应变速率降低,动态再结晶逐渐取代动态回复成为合金的主要软化机制。     

PP／SCF复合材料的制备和力学性能的研究

本文制备了聚丙烯（PP）／,短炭纤维（SCF）复合材料并研究了其力学性能。结果表明,复合材料的拉伸强度随SCF含量的增加有先增加后趋于稳定的趋势,当SCF含量达到6％时,拉伸强度达到极值。随着SCF的加入,冲击强度呈先增加后略有降低的趋势,复合材料在SCF含量为6％时冲击强度达到极值。由此可知,适量的加入SCF对PP起到了较好的增强增韧效果。