AR与ARMA有色噪声的生成方法

基于自回归与自回归滑动平均模型。讨论了两种有色噪声的软件生成方法，可使输出序列无起始瞬为现象，给定功率谱函数结构时采用递推算法。给定滤波器系数时采用步降法。分别给出了滤波器的两种设计流程。通过设置滤波器的初始状态，使得在白噪声激励下滤波器的输出序列稳定，无起始瞬变现象。     

模拟地球同步轨道辐照环境对光学太阳反射镜性能的影响

研究了模拟地球同步轨道辐照环境对卫星用温控涂层-光学太阳反射镜(OSR)性能的影响。对所研制的两类OSR 片进行的辐照试验项目有,真空紫外辐照、低能电子和两种能量的质子辐照。此外还进行了等离子体环境条件下的表面充/放电效应试验。经过相当于安装在地球同步轨道卫星南北极位置处,在空间七年所受到的电子、质子和紫外辐照总剂量的辐照后,导电型OSR 的太阳光谱吸收率α_s 由0.068增加到0.078,法向发射率ε_n 由0.83降低到0.72;而非导电型OSR的α_s 由0.066增加到0.085,ε_n 由0.82降低到0.76。表面充/放电试验的结果表明:导电型OSR 的充电电位仅在15～40V 之间,而非导电型OSR 的充电电位则可高达13kV。因此导电型OSR能有效地控制表面的充/放电现象。     

微重力场中对流—辐射—传质系统的地面模拟技术

研究了微重力条件下对流－辐射－传质稳态系统的地面相似模拟技术，进一步发 温度－材料综合保护技术。通过采取补偿热流，调整壁面热流密度分布的方法，保持了原型与尺寸适当缩小后的模型的Ｎｕ数，Ｓｈ数，材料，温度，湿度不变，从而实现模型与原型流动，换热和传质相似。     

相位噪声测量技术的发展

随着相位噪声参数广泛的应用,其测量技术得到不断的发展,除了传统模式的相位噪声测量系统外,一些采用新技术的测量系统不断的被开发出来,包括应用互相关原理的信号源分析仪和应用高速数字信号处理的直接数字化相位噪声分析仪,它们各具优势,也将会得到广泛应用。     

防静电白色热控涂层的空间环境性能试验

通过在氧化锌晶格中掺入重金属离子，得到具有防静电功能的白色颜料，再以丙烯酸树脂为粘合剂制备出空间飞行器外表面用的ACR－1防静电白色热控涂层；研究了空间环境效应（包括紫外辐照，电子和质子辐照）对该热控涂层太阳吸收率的影响并与有机硅白色热控涂层进行了比较，地面模拟空间环境试验研究结果证明，ACR－1防静电白色热控涂层具有良好的空间稳定性。     

喷流噪声特性与控制研究

本文着重研究喷流噪声机理及工程计算方法。通过实验研究了声功率与喷流速度的关系,表明在Mα>0.4时Lighthill方程和Lilley方程均与实验数据吻合,可分别使用。而Mα<0.4时,均偏差较大,通过本文实验表明,若改为6次方关系较为恰当。文章同时对喷流噪声指向性、谱特性进行了分析。最后对一种引射消声器进行了发展性研究,获得在135dB噪声条件下,降噪17dB的效果。     

Noise in wireless systems from solar radio bursts

Solar radio bursts were first discovered as result of their interference in early defensive radar systems during the Second World War (1942). Such bursts can still affect radar systems, as well as new wireless technologies. We have investigated a forty-year record of solar radio burst data (1960–1999) as well as several individual radio events in the 23rd solar cycle. This paper reviews the results of a portion of this research. Statistically, for frequencies f  1 GHz (near current wireless bands), there can be a burst with amplitudes >10³ solar flux units (SFU; 1 SFU = 10⁻²² W/m²) every few days during solar maximum conditions, and such burst levels can produce problems in contemporary wireless systems.     

微重力下管肋式空间辐射器的整体优化分析

建立了向一重力环境下管肋式空间辐射器传热过程的数学模型，并以单质量散热量最大和热载体驱动功率最小为优化目标，对管式空间辐射器进行了优化分析。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.