推力矢量和二元喷管

推力矢量是第四代战斗机获得过失速机动性的必要条件,而二元喷管又是推力矢量控制中性能较为优越的一类喷管。本文较全面地阐述了目前世界上推力矢量和二元喷管的发展和现况、二元喷管的构造和性能、二元喷管对改进飞机升阻特性和机动的作用。推力矢量能显著提高飞机在空战中的作战效率以及推力矢量控制所需的效能也在文中作了介绍。     

Modeling novel methodologies for unmanned aerial systems–Applications to the UAS-S4 Ehecatl and the UAS-S45 Bálaam

The rising demand for Unmanned Aerial Systems(UASs) to perform tasks in hostile environments has emphasized the need for their simulation models for the preliminary evaluations of their missions. The efficiency of the UAS model is directly related to its capacity to estimate its flight dynamics with minimum computational resources. The literature describes several techniques to estimate accurate aircraft flight dynamics. Most of them are based on system identification. This paper presents an alternative methodology to obtain complete model of the S4 and S45 unmanned aerial systems. The UAS-S4 and the UAS-S45 models were divided into four sub-models, each corresponding to a specific discipline: aerodynamics, propulsion, mass and inertia, and actuator. The‘‘aerodynamic" sub-model was built using the Fderivatives in-house code, which is an improvement of the classical DATCOM procedure. The ‘‘propulsion" sub-model was obtained by coupling a two-stroke engine model based on the ideal Otto cycle and a Blade Element Theory(BET) analysis of the propeller. The ‘‘mass and the inertia" sub-model was designed utilizing the Raymer and DATCOM methodologies. A sub-model of an actuator using servomotor characteristics was employed to complete the model. The total model was then checked by validation of each submodel with numerical and experimental data. The results indicate that the obtained model was accurate and could be used to design a flight simulator.     

对空间碎片近距随遇悬停的控制方法及悬停燃耗分析

对空间碎片检视或抓捕操控中的悬停控制及燃耗问题进行了研究。通过C W方程，建立任务星近距随遇定点悬停控制模型，通过设计状态反馈控制器分析定点悬停的可控性以及推控要求，结果表明近距悬停需要与悬停位置相关的两个正交方向上的常值连续推力控制量，以及用于抵抗扰动的三轴向上的反馈变推力控制量。分析了近距随遇悬停的推控分系统配置，建立了长时近距随遇悬停的燃耗及燃耗速率的数学模型，最后分析了既满足安全距离需求、又满足悬停方位需求的最小悬停燃耗模型。     

低速大转矩永磁游标电机在发酵罐中的应用

采用秸秆生产丁醇时,为了达到高效率发酵,需要使发酵液中菌体分布均匀,所加物料需要及时搅拌。工业化生产丁醇的发酵罐尺寸较大,搅拌过程对驱动电机的输出转矩要求较高,因此高效率、小体积、低速大转矩的秸秆发酵搅拌电机对工业化发酵生产丁醇意义重大。设计了一种定转子永磁游标电机用于发酵液搅拌,并对电机的槽极数、电磁性能进行了具体的研究。制造样机并采用滞环控制实现了对液态发酵对象的快速响应,且实现了低能耗、高效率的发酵过程。     

镁合金绿色高效焊接技术研究进展

镁合金是航空航天领域应用最为广泛的轻合金之一.随着镁合金应用的不断深入,对具有高精度、低能耗、高效率特征的绿色焊接技术提出了迫切需求,并成为镁合金焊接制造发展的重要方向.针对上述需求,围绕镁合金激光诱导电弧复合焊接技术,镁合金活性高效焊接技术以及镁合金与异种金属的连接技术展开系统研究.采用激光诱导电弧复合焊接技术成功实现了镁合金低能耗高效焊接制造,与传统电弧焊接相比显著提高了焊接制造效率,降低了焊接制造能耗.采用激光胶焊技术及激光-电弧复合焊接技术实现了镁合金与铝合金及镁合金和钢铁的高性能焊接制造.上述绿色焊接制造技术研究成果为实现航空镁合金轻量化结构件的设计和制造提供了有力支撑.     

供热系统集约化运行的能耗监测及节能调节问题探讨

对我校供热系统的现状进行了分析；指出了锅炉热效率及能耗监控方面的不足，并针对锅炉热效率提高和二次网循环泵变频调节进行了节能分析计算；同时根据我校实际情况对循环泵设备配置及控制进行了分析，提出了要加强技术指标量化考核和能耗监测，提高效率、节能降耗，实现供热系统的科学化、集约化运行。     

卫星AIT阶段推进系统压力参数处理方法

在双组元推进系统管路中,高压气路、氧路、燃路分别装有一个压力传感器,通过压力传感器的遥测参数获取相应管路中压力情况。文章以某双组元卫星为例给出整星装配、总装与测试（AIT）阶段卫星推进系统压力参数处理方法,为卫星压力参数的纵向数据比对提供判读依据。通过该方法可以间接检查相应管路的气密性。     

某型APU主机滑油消耗量大故障排除

针对某型辅助动力装置修理后试车中多次出现主机滑油消耗量大的故障,分析了辅助动力装置滑油系统工作原理,查找故障原因,并制订了相应的控制措施,解决了因主机修理原因造成的辅助动力装置滑油消耗量大故障。     

柴油发动机热管理系统的高度特性

基于空中和高原环境的特点,研究了柴油发动机散热器传热性能的高度特性;进一步建立了发动机热管理系统的流动和传热模型,研究了热管理系统的高度特性;给出了基于最小功耗原则的热管理系统运行参数匹配方法.在固定系统热负荷条件下的计算结果表明:随着海拔高度的增加,在空中环境下,散热器的散热性能先上升后下降,热管理系统中冷却液和润滑油温度先下降后上升,热管理系统所需的最小功耗先减小后增加;在高原环境下,散热器的散热性能随高度增加大幅下降,热管理系统中冷却液和润滑油温度大幅上升,发动机出现过热问题,为了给发动机提供足够的散热能力,热管理系统所需要的最小功耗随着海拔高度的增加而大幅增加.      

Streamwise-body-force-model for rapid simulation combining internal and external flow fields

A streamwise-body-force-model (SBFM) is developed and applied in the overall flow simulation for the distributed propulsion system, combining internal and external flow fields. In view of axial stage effects, fan or compressor effects could be simplified as body forces along the streamline. These body forces which are functions of local parameters could be added as source terms in Navier-Stokes equations to replace solid boundary conditions of blades and hubs. The val-idation of SBFM with uniform inlet and distortion inlet of compressors shows that pressure perfor-mance characteristics agree well with experimental data. A three-dimensional simulation of the integration configuration, via a blended wing body aircraft with a distributed propulsion system using the SBFM, has been completed. Lift coefficient and drag coefficient agree well with wind tun-nel test results. Results show that to reach the goal of rapid integrated simulation combining inter-nal and external flow fields, the computational fluid dynamics method based on SBFM is reasonable.