受均匀内压作用的偏置孔边径向裂纹的应力强度因子的一种求解方法

本文利用一种新的混合法——光弹性实验与权函数解法相结合求解了孔壁受均匀内压作用偏置圆孔边径向裂纹的应力强度因子,该方法具有简单、经济、精度高等优点,对分析复杂应力场中圆孔边穿透裂纹问题,该方法同样适用,且优点更为突出.     

钻孔法测量残余应力时释放系数的标定与计算

 <正> 用钻孔法测量残余应力时,使用的释放系数将对构件的残余应力测量精变产生影响。计算释放系数的理论方法有多种。其中普遍应用的公式,是由弹性力学通孔公式推导的应变片中心点处计算式。     

VARIABLE STRUCTURE CONTROL OF AIRCRAFTFOR ATMOSPHERIC DISTURBANCE

ＶＡＲＩＡＢＬＥＳＴＲＵＣＴＵＲＥＣＯＮＴＲＯＬＯＦＡＩＲＣＲＡＦＴＦＯＲＡＴＭＯＳＰＨＥＲＩＣＤＩＳＴＵＲＢＡＮＣＥＺｈｕＸｉａｏｐｉｎｇ；ＺｈｏｕＺｈｏｕ（ＮａｎｊｉｎｇＵｎｉｖｅｒｓｉｔｙｏｆＡｅｒｏｎａｕｔｉｃｓａｎｄＡｓｔｒｏｎａｕｔｉｃｓ...     

TC4钛合金紧固件孔E-I强化研究

 介绍TC4(Ti-6Al-4V)钛合金螺栓孔无衬套冷胀孔干涉配合综合强化的研究结果。实验证明,在给定的条件下,冷胀孔强化的TC4板状空孔试件的疲劳寿命增益系数(LIF)为13,干涉配合螺栓连接的LIF=3,而E-l强化件的疲劳寿命比单纯干涉配合又有成倍提高。电镜断口分析表明TC4合金强化件的疲劳裂纹的形成和扩展与LY12CZ及30CrMnSiA相似,它们不表现为典型的角裂纹,即沿板平面和厚向扩展速率有明显差异。对于TC4合金,在改善疲劳品质上,带衬套冷胀孔强化比无衬套冷胀孔强化好得多。     

异型孔空心叶片壁厚检测的试验研究

发动机叶片的结构型式和制造误差，直接影响发动机的性能和使用寿命。运用超声波法和电涡流法，对两种不同材料和形式的试件进行了试验。电涡流法受到探头直径和试件几何尺寸的影响，测量误差大，超声波法由于存在测量盲区，测量厚度的下限受到限制。但测量值与实际值相关，若对探头加以改进，用于异型孔空心叶片壁厚检测是可行的。     

Spectra and time variability of black-hole binaries in the low/hard state

We propose a jet model for the low/hard state of galactic black-hole X-ray sources which explains the energy spectra from radio to X-rays and a number of timing properties in the X-ray domain such as the time lag spectra, the hardening of the power density spectra and the narrowing of the autocorrelation function with increasing photon energy. The model assumes that (i) there is a magnetic field along the axis of the jet, (ii) the electron density in the jet drops inversely proportional to distance, (iii) the jet is “hotter” near its center than at its periphery, and (iv) the electrons in the jet follow a power-law distribution function. We have performed Monte Carlo simulations of Compton upscattering of soft photons from the accretion disk and have found power-law high-energy spectra with photon-number index in the range 1.5–2 and cutoff at a few hundred keV, power-law time lags versus Fourier frequency with index 0.8, and an increase of the rms amplitude of variability and a narrowing of the autocorrelation function with increasing photon energy as they have been observed in Cygnus X-1. The spectrum at long wavelengths (radio, infrared, optical) is modeled to come from synchrotron radiation of the energetic electrons in the jet. We find flat to inverted radio spectra that extend from the radio up to about the optical band. For magnetic field strengths of the order 10⁵–10⁶ G at the base of the jet, the calculated spectra agree well in slope and flux with the observations.     

二元曲面可调进气道流量系数精确预测方法

为了满足二元曲面可调进气道模态转换马赫数范围(来流马赫数为2.2~3.2)的流量要求,针对唇口平移、转动和转动+平移三种调节方案,基于理论分析和基准进气道的流场,提出了一种流量系数精确预测方法,并通过数值计算进行验证且获得了进气道的总体性能。结果表明:调节后的进气道流量系数与预测值完全相等,而且无需多次试算,符合设计预期,可拓展应用于轴对称进气道。相对基准进气道,唇口前移时流量系数和压缩效率同时增加,来流马赫数为2.5时出口总压恢复系数相等而增压比增加了14.6%;在降低相同流量系数条件下,后移唇口使得增压比和压缩效率均降低,来流马赫数为2.5时出口总压恢复系数基本相等而增压比减小了12.9%,转动唇口使增压比进一步减小了9.1%,唇口后移方案性能更优。      

飞机数字化装配系统中机身交点孔加工方法研究

针对传统交点孔加工方法加工精度低且存在回弹变形的问题,设计了一种满足飞机大部件数字化装配要求的机身交点孔精加工方法,根据交点孔的加工特性完成了机身定位与固持、数控加工中心定位以及加工工艺的总体设计,确定了交点孔加工程序原点的计算方法和编程原则,最后通过交点孔试切加工试验验证了加工方法的可行性。     

内孔结构对旋转空化发生器水力特性的影响

空化普遍存在于工业生产、舰船推进、航空航天等领域.使用高速相机对闭式循环试验台的旋转空化发生器内部流动进行试验观测，然后基于RNG k ε湍流模型和Zwart Gerber Belamri空化模型开展了旋转空化发生器流场的数值模拟.结果表明数值模拟结果与试验观测数据吻合较好，验证了本文数值模拟方法的准确性和可靠性.受离心力作用，转子孔内的压力从内径到外径逐渐增大.内孔底部由于轴向旋涡的作用，产生较大旋涡并耗散能量.内孔顶部流体与腔体区主流相互作用，在内孔顶侧产生碰撞并形成较小漩涡.不同内孔结构对旋转空化发生器的空化效果具有重要影响，在相同工况下椭圆形内孔的空化率小于圆锥形和圆柱形，说明型线光滑的内孔结构局部损失小，产生的空化较弱.不同内孔结构下，旋转空化发生器内部压力脉动的主频为转频fi或24fi(对应圆周方向开孔排数)，压力脉动最大幅值出现在进口管侧和出口管侧，主要原因是受动静干涉作用影响.     

An equilibrium multi-objective optimum design for non-circular clearance hole of disk with discrete variables

An Equilibrium Multi-objective Optimization Model(EMOM) with self-regulated weighting factors has been proposed for the optimum design of non-circular clearance hole on the front flange of turbine disk. In the ‘‘equilibrium design", both the stress decrease around the hole and the least hole's profile variation are considered, which balances two ambivalent design goals. Specific discrete variables are applied to realize the standardization design in the optimization process, in which a Surrogate Genetic Coding Algorithm(SGCA) is introduced, and a special check module is used to get rid of repeated fitness evaluation of the samples. The method offers an equilibrium design for the non-circular clearance hole of the turbine disk with great accuracy and efficiency.